Singer Futura XL-400 Support Question
Singer Futura XL-400 Support Question
Find answers below for this question about Singer Futura XL-400.Need a Singer Futura XL-400 manual? We have 1 online manual for this item!
Question posted by sherylchampy on December 28th, 2013
Where Is The Connector Cap I Am Suppose To Turn To The Right
Where is the connector cap that I need to turn to the right before adding embroid. unit on.
Current Answers
Related Singer Futura XL-400 Manual Pages
Instruction Manual - Page 2
... attachments recommended by the manufacturer as a toy. Keep ventilation openings of the sewing machine and foot control free from all instructions before
operating
"SAVE THESE INSTRUCTIONS" "...relating to the nearest authorized dealer or service center for their safety. "To disconnect, turn switch to the off
before carrying out any adjustments in the needle area, such ...rights reserved.
Instruction Manual - Page 5
... messages 108 - 109
For European version
Sewing machine Dimensions: 567 mm × 240 mm × 317 mm Mass of the equipment: 10.8 kg
Embroidery unit Dimensions: 504 mm × 411 mm... patterns 50 - 51 Sewing on a button 50 - 51 Buttonholes 52 - 57
Using buttonhole foot, Procedure, Corded buttonholes Buttonholing with Futura Multi hoop 88 - 95 Helpful messages when embroidering 96 - 97
4.
Instruction Manual - Page 8
...Presser foot screw
17
23. Needle bar
26. Needle clamp screw
25
29. Needle plate 32. Embroidery unit 34 Hoop release lever 35. Connector 41. Large hoop
36 35 37
34 40 20 21 22 23 24
38 39
27 28 29 30...Hand wheel
14. Hoop bracket 39. Carriage 36. Presser foot lifter
19. GETTING TO KNOW YOUR MACHINE
MACHINE IDENTIFICATION
2
1
8
1. Bobbin cover release button 33.
Instruction Manual - Page 10
...
Embroidery software CD
19
FUTURA embroidery is "system" of your
7
Sewing machine is another
12
very ...machine and the software providing powerful option and capabilities. Embroidery presser foot 23. Screwdriver (small)
12. Button sewing foot
1
16. Thread spool net (short)
The Foot that comes on your
sewing. Spool pin cap (large)
8. Bobbins 21. Spool pin cap...
Instruction Manual - Page 12
...by removing the plug from needle plate area before using sewing machine only.
NOTE: In sewing mode, the machine can be disconnected from the power supply. The same switch...Your machine will not operate until the power/light switch is turned on the spool pin. When servicing the machine, or when changing needles or lights, etc., the machine must be operated either
with a spool cap to...
Instruction Manual - Page 18
... check:
1.) With the presser foot raised, pull the thread towards the the back of the needle. Always be obtained.)
B. Turn the hand wheel counter clockwise (toward you have mis-threaded the machine and need to raise the presser foot lifter before threading the top thread. (If the presser foot lifter is in the...
Instruction Manual - Page 24
... needle is recommended for buttonholes to adjust the tension control. Lower the presser foot lifter so that the machine is irregular, you find that for straight stitch sewing.
If, when you start to sew, you will need to adjust it. Make all adjustments with the foot holder. 3. Helpful Hint: A slight adjustment to remove the...
Instruction Manual - Page 26
...pattern will be lit. At this point you may sew Straight Stitch. To select other patterns, push the pattern selection button to the right of length and width.
*REMARQUE: les é... y ancho.
CONTROL PANEL FUNCTIONS
Pattern selection buttons
Turn on the length and width controls are for reference only and do not represent actual sewing parameters of the row that contains your pattern is...
Instruction Manual - Page 28
... position, slide the control knob left or right to locate each manual adjustment point, the ...turns on when twin needle sewing is activated.
26 The LED Indicator next to move the control knobs while sewing slowly. At each of the potential adjustments. The LED turns on when twin needle sewing...Auto/Default settings Your sewing machine will produce most of your preference.
When a ...
Instruction Manual - Page 30
...
3
When the machine is turned on all patterns. However, when foot control is set at its up -stop
position with lower LED lamp lit. When foot control is pushed once more, the machine stops. LED INDICATOR
Green light indicates machine is set at its up -stop position with LED lit. The sewing machine makes 4 tiny...
Instruction Manual - Page 34
... below.
1. Thread tension control B. Reverse stitch button E. Start/stop the sewing machine. Stitch width control J. Pull both Metric and Inch Markings as shown.
Stitch... the rear and cut off excess
thread with your fabric when sewing a seam.
6. Power/light switch
F G
2
H I . First turn the handwheel counter clockwise (toward the back of the
face cover, as ...
Instruction Manual - Page 40
... the guide on the right side of the fabric. First finish the raw edge. Now fold the fabric as illustrated. Turn the handwheel counter
3
clockwise (toward you) by turning it under the foot...under on fine fabrics or overcasting it does
A
not, adjust the guide (B) on medium to sew blind hem. Then turn the hem up the required depth, press and pin in place.
2. BLIND STITCH
SETTINGS :...
Instruction Manual - Page 52
... :Feed dog control -
Sew 10 stitches across. SEWING ON A BUTTON
SETTINGS :Presser foot - Helpful Hint: To secure thread, pull both the left and right openings of the fabric and tie together.
50 Adjust width if required. Satin foot :Thread tension control - CONTINUOUS DECORATIVE PATTERNS
SETTINGS :Presser foot - Turn the hand wheel counter clockwise (toward...
Instruction Manual - Page 60
...SEWING
BEFORE ATTACHING EMBROIDERY UNIT ATTACHING EMBROIDERY FOOT
Foot holder Support du pied Sujetador prensatelas
Always be sure to move needle up and down , and check that the drive lever is required for embroidering, so
be sure to turn... de accionamiento
Be careful not to machine CAUTION before changing presser foot.
* Raise presser foot lifter. Turn hand wheel toward you to use ...
Instruction Manual - Page 64
... distorted.
Turn connector cap to the right to the embroidery unit.
To make sure that the embroidery unit is not securely installed, the finished embroidery may cause CAUTION damage to open. Don't push the carriage or put strong pressure on the machine and embroidery unit. Doing so may be sure to turn off power to close for general sewing.
3
Handle...
Instruction Manual - Page 76
... hoop. IMPORTANT: If you have embroidered using the small hoop, and you are now ready to your embroidery unit.
3. Pressing the "Next" button will finally start -up the Futura Software.
4. Please wait for proper start the copy and installation of available space on your computer.
Turn on your computer and sewing machine.
1. You can always abort...
Instruction Manual - Page 90
...sews them precisely, matching one section to the other . The vertical and horizontal lines must be at precise right.... Multi-Hoop
Multi-Hooping is a special feature in the Futura software that will allow embroidery data which is larger than a... three alignment points (A, B, and C) are input, they inform the machine exactly as the design data requires.
Intersección de las lí...
Instruction Manual - Page 102
... 22 - 23). * Needle is not threaded correctly. (see page 10 - 11). * Buttonhole lever is turned off.- Bobbin thread breaks. * Bobbin case is bent. -
PERFORMANCE CHECKLIST
GENERAL PROBLEMS Machine does not sew. * Power switch is not raised when sewing stitch patterns.
- Turn on the switch. (see page 14 - 15). * Lint accumulates in hook. - Lower buttonhole lever...
Instruction Manual - Page 104
... the needle plate toward you as indicated by removing the plug from the sewing machine and footcontroller.
NOTE: U se dry rags to its highest position and ...and hook area with the projection (3) positioned
5
against the spring (4).
(2)
(A) (B)
6. Cleaning the sewing machine and footcontroller
After using, keep the essential parts clean at its highest position.
2
2. Make sure ...
Instruction Manual - Page 106
... Vis Guia
104 OILING INSIDE THE FACE COVER
1. Put one drop of oil other than Sewing Machine Oil will cause damage to the points indicated
by arrows.
1 Face cover Plaque frontale Cubierta frontal
Helpful Hints : For the machine used after a long interval : It should be oiled before oiling.
For best results always use...
Similar Questions
What Is The Part Number For Face Cover Screw For Futura Xl420?
I have lost the screw that holds the face cover in place. It is the one on the side that is under th...
I have lost the screw that holds the face cover in place. It is the one on the side that is under th...
(Posted by barbara27028 3 years ago)
Replacement Part For Singer Futura Xl 400
I am looking for the embroidery arm unit for a Singer Futura Xl 400. Can you assist me in locating t...
I am looking for the embroidery arm unit for a Singer Futura Xl 400. Can you assist me in locating t...
(Posted by sjh4ba 3 years ago)
Singer Futura Xl-400
I am in need of a Singer Futura XL-400 Startup disc. Any idea where I can get one
I am in need of a Singer Futura XL-400 Startup disc. Any idea where I can get one
(Posted by fayevb 4 years ago)
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)