Sharp XR-30X Support Question
Sharp XR-30X Support Question
Find answers below for this question about Sharp XR-30X - XGA DLP Projector.Need a Sharp XR-30X manual? We have 1 online manual for this item!
Question posted by tracynewman on March 13th, 2010
Lamp Won't Light
After replacing the Lamp in my Sharp XR30X projector, the power light is green and steady, but the lamp light is green and blinks in the following sequence: 1 long, 14 short. The fan runs but the lamp is not lighting. What is wrong?
Current Answers
Related Sharp XR-30X Manual Pages
Operation Manual - Page 5
... PARTS EXCEPT LAMP UNIT. The lightning flash with the projector.
1. ONLY
1 Be especially careful that any safety notification of your purchase.
2. WARNING: To reduce the risk of light.
Introduction
Before...benefit of the parts, service and labor warranty applicable to your new SHARP Projector, using the projector, please read this equipment. Do not stare into the
beam of ...
Operation Manual - Page 6
... equipment generates, uses, and can
be regulated due to environmental considerations. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL XR-40X/XR-30X/XR-30S This device complies with Part 15 of mercury. ONLY
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of the FCC rules. For disposal or recycling information, please contact...
Operation Manual - Page 7
However, you can also be performed by using the projector.
ADJ
Picture Mode
Contrast Bright Red Blue
CLR Temp Bright Boost Lamp Setting
Reset
PRJ - ADJ
Standard 0 0 0 0 0 1...using the buttons on the model. Example: "Picture" screen menu for setting up and operating the
projector. ENTER
END
Useful Features
Button used in the same manner.
• In this operation
Menu ...
Operation Manual - Page 8
...14 Usable Range 15
Quick Start
Quick Start 16
Setup
Setting up the Projector 18 Setting up the Projector...Projector to Other Equipment 21
Controlling the Projector by a Computer 24
Connecting the Power Cord 24
Using
Basic Operation
Turning the Projector On/Off 25 Turning the Projector on 25 Turning the Power off (Putting the Projector...232C 44 Fan Mode Setting 44 Checking the Lamp Life ...
Operation Manual - Page 12
.... Caution concerning the lamp unit ■ Potential hazard of the lens. Do not set "Fan Mode" to hard impact and/or vibration. ■ Protect the lens so as mountains (at least 10 minutes. Close the curtains and dim the lights when setting up your nearest Sharp Authorized Projector Dealer or Service Center for replacement. Do not...
Operation Manual - Page 13
... wall outlet, and disconnect any other cables connected to it. ■ If the power cord is unplugged while the cooling fan is automatically controlled. Info
• The cooling fan regulates the internal temperature, and its performance is running, some parts of the projector may still be hot. How to "Maintenance In- Note
• If the...
Operation Manual - Page 14
... to the wall outlet in your nearest Sharp Authorized Projector Dealer or Service Center.
10 Please check with your country. • Operation manual (this manual and CD-ROM )
Note • Codes in "< >" are Replacement parts codes.
and
For Australia, New
Singapore
Zealand and Oceania
(6' (1.8 m))
(6' (1.8 m))
* Use the power cord that corresponds to mini D-sub 15...
Operation Manual - Page 15
... setting
37
items selected
or adjusted on and putting the projector into standby mode.
Push both sides of the cooling fan and extending the lamp life.
29
VOL (Volume) buttons (-O/Q+)
For adjusting the... in Z refer to attach or remove.
11 Projector
Top View
Power indicator
25, 48
STANDBY/ON 25
button For turning the power on
the menu.
Introduction
Part Names and Functions
...
Operation Manual - Page 17
...ECO+QUIET button 32
For lowering the noise of the cooling fan and extending the lamp life.
25 ON button
For turning the power on.
33 FREEZE button
For freezing images.
29 AV ... automatically adjusting images when connected to the respective input modes. STANDBY button
25
For putting the
projector into the
standby mode.
MOUSE/Adjustment 34 buttons (P/R/O/Q) 37
• For moving the computer...
Operation Manual - Page 19
ever, the effective distance of the signal may malfunction under a fluorescent lamp. In this case, move the projector away from the remote control can be re- Introduction
Usable Range
The remote ...• Ensure that you do not drop it or expose it to control the projector within the ranges shown in the illustration. Remote control sensor
Note
• The signal from the fluorescent...
Operation Manual - Page 29
... shut down abnormally or the lamp should be turned on . Green: The lamp is turned off (Putting the Projector into standby mode.
• The projector cannot be replaced.
• When switching on the projector, a slight flickering of the lamp. On-screen display (confirmation message)
Info
• Direct Power Off function: You can unplug the power cord from the outlet or...
Operation Manual - Page 36
... disappear.
1 Press BREAK TIMER. • The timer starts to count down , the power consumption will decrease, and the lamp life will extend.
jector is set in units of one minute (up to "Lamp Setting" on page 40 for details of the cooling fan will turn down from 5 minutes. Operating with O or R 4 minutes s 3 minutes s1...
Operation Manual - Page 39
...XR-40X/XR-30X. *6 Adjustment range for XR-30S. ENTER
END
COMPUTER (Component), DVI (Component), S-VIDEO, VIDEO input
Picture
SCR - ADJ
Help
Standard 0 0 0 0 0 0 1
3D Progressive Bright
Sharp
-30 +30 *2
Page 40
CLR Temp
-2 2
Page 40
Bright Boost [0/1/2]
Page 40
Progressive
Page 40
Lamp... the projector. ADJ
Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset...
Operation Manual - Page 40
Menu Items (Continued)
"Projector adjustment (PRJ-ADJ)" menu... items vary depending on the input signal and the selected input mode. ADJ
Page 43
Auto Power Off [On/Off]
Page 43
Auto Restart [On/Off]
Page 43
STANDBY Mode
Page 43...[On/Off]
Page 43
Audio Input
Page 43
RS-232C
Page 44
Fan Mode
Page 44
System Lock [Enable/Disable]
Page 44
Lamp Timer(Life)
Page 44
Sub menu
Standard Eco
Audio 1 Audio 2 ...
Operation Manual - Page 52
...is abnormally high. (See page 49.)
48
Indicators on the Projector Power indicator
Lamp indicator
Temperature warning indicator
Red on Green on Red blinks Green blinks Green on Green blinks Red on
Off Red on
Normal (Standby) Normal (Power on the screen. Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on
page 49. About...
Operation Manual - Page 53
... connect it again.
• Carefully replace the lamp. (See page 51.)
• Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for repair.
• Please exercise care when replacing the lamp.
• Securely install the cover.
• If the power indicator blinks in red when the projector is on (Standby)
Problem
The internal...
Operation Manual - Page 54
... may cause burns or injury.
• Wait at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not light after the power cord is disconnected to allow the surface of the projector. IMPORTANT NOTE TO U.S. All service of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO...
Operation Manual - Page 60
... High 0:Off, 4:Lamp Error
3:Waiting, 4:Lamp Error
T P O W _ _ _ 1 1:On, 2:Cooling
0:Standby
T L PN_ _ _11 T L T T _ _ _ 1 0 - 9999(Integer) T L T M _ _ _ 1 0, 15, 30, 45 T L T L _ _ _ 1 0% - 100%(Integer) T N A M _ _ _ 1 XR40X / XR30X / XR30S M N R D _ _ _ 1 XR-40X / XR-30X / XR-30S
P J N 1 * * * * OK or ERR
P J N 2 * * * * OK or ERR
P J N 3 * * * * OK or ERR
P J N 0 _ _ _ 1 Projector Name...
Operation Manual - Page 65
... incorrectly connected to the projector.
• "Bright" is set when connecting notebook computer.
• The lamp unit cover is not ...run out.
• External output has not been set to minimum position.
• Depending on the lens. This will become blurred. Check
• Projector power cord is not plugged into a warm room, or if it is fog on the computer you turn up the projector...
Operation Manual - Page 66
... in red.
If this happens frequently, replace the lamp. the projector illuminates
or blinks in the "Help" menu, after selecting an item other than 5 minutes.
62
Picture is dark. The cooling fan becomes • When temperature inside the projector increases, the cooling fan
noisy. runs faster.
The lamp needs much • The lamp will not be affected by incorrect operation...
Similar Questions
Sharp Xr 10s - Notevision Svga Dlp Projector.
Main board needed. Where can I get? Used is fine. Budget $20
Main board needed. Where can I get? Used is fine. Budget $20
(Posted by sanoorvishwa 8 years ago)
What Does Green Blinking Lamp Light Mean? What Does Red Lamp Light Mean?
(Posted by cwrightoh 11 years ago)
Sahrp Pg-f317x Power Green E Lamp Blinking Green And Return Standy By Lamp New
INPUT THE POWER CORD IN PROJECTOR AND POWER GREEN AND LAMP BLINKING GREEN BACK SOON TO STANDY BY MOD...
INPUT THE POWER CORD IN PROJECTOR AND POWER GREEN AND LAMP BLINKING GREEN BACK SOON TO STANDY BY MOD...
(Posted by projetecrs 12 years ago)
Using Multimedia Xr-30x W/o Remote
how do I use xr 30x projector w/o remote
how do I use xr 30x projector w/o remote
(Posted by Anonymous-32881 12 years ago)
After Replacing The Lamp In My Sharp Xr30x Projector, The Power Light Is Green A
After replacing the Lamp in my Sharp XR30X projector, the power light is green and steady, but the l...
After replacing the Lamp in my Sharp XR30X projector, the power light is green and steady, but the l...
(Posted by tracynewman 14 years ago)