Ryobi TSS101L Support Question
Ryobi TSS101L Support Question
Find answers below for this question about Ryobi TSS101L.Need a Ryobi TSS101L manual? We have 4 online manuals for this item!
Question posted by tparrisparris on March 5th, 2020
Aligning Laser
How do I align the laser better? The laser shines just off the cutting line. I want it more exact.
Current Answers
Answer #1: Posted by Troubleshooter101 on March 5th, 2020 9:20 AM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,030
Member since:
September 30th, 2015 Points: 2,927,030
Use hidden adjustments to fine tune the laser alignment for Ryobi miter saws. Adjust pivot, angle and position.
Please check this link for video tutorial
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related Ryobi TSS101L Manual Pages
English Manual - Page 1
SLIDING COMPOUND MITER SAW with Laser
TSS100L
Your miter saw has been engineered and manufactured to our high standard for , it will give you for purchase.
SAVE THIS MANUAL FOR FUTURE ...
English Manual - Page 3
...PROPER Extension Cord. Wear a face or dust mask if the cutting operation is tipped.
CHECK DAMAGED PARTS. Make sure your...Failure to do the job better and safer at least 14 is off .
3 Do not let visitors contact tool or extension cord while ... DRESS PROPERLY. Follow instructions for alignment of moving parts, binding of operation.
DO NOT ...
English Manual - Page 5
...before raising the blade out of workpiece.
THIS TOOL should any cutting angle while the saw blade to come to avoid serious ...this saw to a work using the laser guide.
This saw can result in or near the cutting path of saw blade. ALWAYS REMEMBER...any way, or should have any part of the body in line with safe operation BEFORE performing any use of the workpiece.
...
English Manual - Page 6
..., avoid contact with side shields and, as necessary, a full face shield when operating this tool. To reduce the risk of injury, user must read and understand operator's manual before using ...Surface
Precautions that involve your hands away from the blade will allow you to operate the tool better and safer. Proper interpretation of the following symbols may be used on this product.
SYMBOLS...
English Manual - Page 9
... Workpiece or Material The item on which a blade or cutting tool is bent (or set) outward from being guided by the blade. Chamfer A cut without the workpiece being kicked back toward operator.
FPM or ...blade binds or stalls, throwing the workpiece back toward the front of the blade. Heel Alignment of turns completed by guiding it applies to the workpiece, that area which helps keep...
English Manual - Page 11
...your compound miter saw has a powerful 13 amp motor with the miter saw .
LASER GUIDE
For more accurate cuts, a laser guide is made with all operating features and safety rules.
10 in this operator's... BRAKE
An electric brake has been provided to another, a carrying handle has been provided on the tool and in . MITER FENCE
The miter fence on both the left side is released.
thick or ...
English Manual - Page 17
... blade guard
Blade BOLT cover
Flat(S) on the spindle. The blade teeth point downward at the front of the saw. Double "D" flats on blade washers align with the flats on Spindle
To LOOSEN
Blade BOLT
flat To washer Tighten
Inner Blade Washer WITH DOUBLE "D"
FLATS
Blade
Outer Blade Washer
WITH DOUBLE...
English Manual - Page 18
... in order to leave the mark. Avoid direct eye contact with using the laser guide: Removing Your Mark: Position the laser line near or over your mark. Make several practice cuts on the work surface in lining up the mark for aligning the laser line with your mark on the work surface.
ASSEMBLY
WARNING:
Make sure the spindle...
English Manual - Page 19
...the saw .
ASSEMBLY
removing / replacing the throat plate
See Figure 17. When making sliding cuts, turn the support foot clockwise or counterclockwise depending on the uneven edges resulting in binding ...can catch on the amount of the throat plate. To reinstall the throat plate, align the holes in the throat
plate with the holes in serious personal injury.
Never operate the...
English Manual - Page 20
... left or right until the pointer on the control arm
is parallel with the square. Retighten the screws securely and recheck the blade-tofence alignment. The saw has two scale indicators, one on the bevel scale and one
leg of the saw blade angles away from the square as shown...
English Manual - Page 21
...not the blade teeth.
Rotate the blade by hand and check the blade-to-table alignment at 0°. Also loosen bevel lock lever.
Adjust positive stop adjustment screw to bring ...it may be necessary to loosen the indicator screws and reset them to zero. Recheck bladeto-table alignment.
See Positive Stop Adjustment in figures 24 and 25, adjustments are needed.
Loosen the...
English Manual - Page 23
... . Grasp the saw blade. Grasp the stock firmly with the
desired angle on the blade at the 0° position. See Figure 32. Align cutting line on the miter table with the edge of a board is placed against the fence. Securely tighten the miter lock handle. Place the workpiece flat...
English Manual - Page 24
...and secure it against the fence. See Figure 32.
Align the cutting line on the blade at the end of the cut is placed against the fence, the board could collapse on the ...cutting across the grain of workpiece. OPERATION
TO Bevel Cut
See Figures 28 - 29. See Figures 38 - 39.
When cutting long pieces of lumber or molding, support the opposite end of the cutting operation just...
English Manual - Page 25
... the bevel lock lever.
Recheck miter angle setting.
Compound Miter Cut
C-CLAMP
Fig. 30
Align the cutting line on the miter scale.
Tighten the miter lock handle securely.
... When cutting long pieces of lumber or molding, support the opposite end of the cutting operation just to Compound Miter Cut
See Figures 30 - 31.
Make a test cut the control arm...
English Manual - Page 27
...saw stopping when the full rear position has been reached after each cut. thick. See Figure 32.
Align the cutting line on the workpiece with the edge of the saw handle away from...is running (turned on the saw, perform a dry run of the saw arm forward. Miter cross cuts are made by 3-1/2 in serious personal injury. Failure to secure the workpiece when possible.
...
English Manual - Page 30
...angle changes the other tool made. Also most walls do a better job of a room are interdependent; When cutting crown molding by this method for accurately cutting crown molding for correct... molding that , when added together, equal exactly 90°.
therefore, you will need to fit properly, crown molding must be used for cutting All Standard (U.S.) crown molding with extreme accuracy...
English Manual - Page 32
..." and the saw has been adjusted at the factory for making accurate cuts. Make any adjustment, make a slight cut to score the wood.
Release the switch trigger and allow the...tool is required.
Unplug the saw blade to relock the bevel. A "grating" sound indicates that are necessary and periodically check the parts alignment to wear. NOTE: When properly aligned, the laser...
English Manual - Page 33
from fence where blade enters) to -table alignment.
Also, when a new blade is installed, it is necessary to check the ... 42. Next, retighten lock nut securing the positive stop limits the blade's downward travel.
Check blade clearance and maximum cutting distance (distance from the miter table s upport. The depth stop adjustment screw from turning while tightening the hex ...
English Manual - Page 36
... contains chemicals known to these chemicals: work in . Some examples of these exposures varies, depending on how often you do this type of work with Laser
TSS100L
WARNING:
Some dust created by calling 1-800-525-2579. Replacement parts can also be purchased online at 1-800-525-2579. Your risk from these...
Repair Sheet - Page 3
... your MITER SAW or when ordering repair parts. Extension Bar, Left 1 Screw (45 1 Clamp 2 Pivot Shaft 1 * Screw (M10 x 10 mm Hex Soc. SLIDING MITER SAW w/LASER - Hd 1 Rubber Feet 5 Base 1 Base Plate 1 Tension Spring 1 * Screw (M5 x 10 mm Flat Hd 3 Ball 1 Miter Angle Label 1 * Screw (M5 x 8 mm Hex Soc. KEY
PART...
Similar Questions
Is There A Replacement For Ryobi Tss101l D Handle & Switch?
Part #s for above: 089100121610 089100121112 Have apparently discontinued. Does anyone have a fix?
Part #s for above: 089100121610 089100121112 Have apparently discontinued. Does anyone have a fix?
(Posted by Math72285 3 years ago)
Problems With Ryobi Sds60
My new Ryobi SDS60 rotary hammer only vibrates the bit and doesn't pound. Is that how it's supposed ...
My new Ryobi SDS60 rotary hammer only vibrates the bit and doesn't pound. Is that how it's supposed ...
(Posted by alan39844 10 years ago)
Ryobi Tss101l Laser Not Working?
I have a brand new Ryobi TSS101L and I see no evidence of a laser working. I looked through the manu...
I have a brand new Ryobi TSS101L and I see no evidence of a laser working. I looked through the manu...
(Posted by linexyc 11 years ago)
Laser Is Diffusing Light Vs A Straight Line. Are There Laser Adjustments?
After a few days use the laser line ceased being a line and it appeared that the light was being dif...
After a few days use the laser line ceased being a line and it appeared that the light was being dif...
(Posted by bigdadmad 11 years ago)
Can't Find 'miter Lock Plate'.
New to power tools, so this is probably a rookie question: Just bought a Ryobi TS1343L, only problem...
New to power tools, so this is probably a rookie question: Just bought a Ryobi TS1343L, only problem...
(Posted by adam56194 11 years ago)