Ryobi RY28000 Support Question
Ryobi RY28000 Support Question
Find answers below for this question about Ryobi RY28000.Need a Ryobi RY28000 manual? We have 1 online manual for this item!
Question posted by gama27 on April 4th, 2012
Engine Stalls
Engine starts fine; however, when accelerating to full throttle with attachment, engine stalls.
Current Answers
Related Ryobi RY28000 Manual Pages
Operator's Manual - Page 5
...breaks. During weather that vibrations from operation.
Always stop the engine and cutting attachment. Check with fire prevention regulations. Symptoms may contribute to increase blood circulation....attachment may increase operator fatigue, which can kill.
Clear the work should never rotate at idle during normal use this unit.
Never start or run the engine...
Operator's Manual - Page 6
...unit without warning if the blade snags, stalls, or binds. Make sure fasteners are properly and securely attached.
Use only the manufacturer's...while it is difficult to spin after throttle trigger is released or engine is properly installed and securely fastened. ...This reaction can be sure
the cutting attachment stops turning when the engine idles. Keep the blade away from moving...
Operator's Manual - Page 7
... to explain the levels of this product.
This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle lubricant.
5 -
Ricochet Gasoline and Lubricant
Thrown objects can ricochet and result in the attachment's Operator's Manual. Some of attachment used on the type of the following signal words and meanings are intended...
Operator's Manual - Page 8
... is locked into place.
6 -
WARNING:
To prevent accidental starting that your product when you are already assembled to stop the engine can cause serious personal injury.
Operation of this product with this operator's manual as well as a knowledge of the cutting area. The attachment connects to the power head by the manufacturer and...
Operator's Manual - Page 9
...could result in the area indicated by the manufacturer of the lower end attachment shaft. HIGH QUALITY 2-CYCLE ENGINE LUBRICANT
GASOLINE
LUBRICANT
1 gallon (US) 1 liter
2.6 oz. 20 ...
Tighten the knob securely. NOTE: The open side of attachment used for gasoline. Recommended fuel: This engine is fully tightened before operating equipment;
Pre-mix unleaded
Immediately...
Operator's Manual - Page 10
... brushcutter from the object that may have. STARTING AND STOPPING
See Figures 6 - 8.
OPERATING THE POWER HEAD
See Figure 5. Prolonged cutting at a comfortable position with the attachment cutting head can be held at partial throttle will expose the user to heed this product to the stop the engine, depress the STOP switch to the retail...
Operator's Manual - Page 11
...the slots on the type of fuel used, the type and amount of lubricant used and as garden chemicals and de-icing salts. You can result in . push the cover up until the ... for adjustment and discontinue use until it stops. If the cutting attachment still moves at idle.
FUEL CAP
WARNING:
Check for the
Run engine until the repair is a fire hazard and must be required depending...
Operator's Manual - Page 12
... Filter Screen earlier in this manual.
emits excessive smoke
Air filter screen is dirty. Use fresh fuel and the correct 2-cycle lubricant mix. (50:1).
Engine starts, runs, and accelerates Idle speed screw on the severity of fuel. TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.
Refer to...
Operator's Manual - Page 14
... pressure regulator or fuel injection system).
(ii) Air/fuel ratio feedback and control system.
(iii) Cold start enrichment system.
(iv) Fuel Tank.
(2) Air Induction System
(i) Controlled hot air intake system.
(ii)... is defective, the part will be hoses, belts and connectors, and other engine components caused by the owner.
The California Air Resources Board's Emission Warranty Parts...
Similar Questions
For Generator Ry 3500 What Kind Og Engine Oil We Need?
for generator ry 3500 what kind og engine oil we need?
for generator ry 3500 what kind og engine oil we need?
(Posted by postin200 7 years ago)
Starts Fine And Runs Well In Half Position. But, Dies In Run Position.
In the HALF position, I can turn the engine upside down and it runs even better, but won't keep runn...
In the HALF position, I can turn the engine upside down and it runs even better, but won't keep runn...
(Posted by jahipps 11 years ago)
Ryobi Ry13010 Carburettor
My Trimmer starts fine and idles fine for a minute or so then stalls as soon as I open the throttle....
My Trimmer starts fine and idles fine for a minute or so then stalls as soon as I open the throttle....
(Posted by terry43343 11 years ago)