RCA ANT702F Support Question

Find answers below for this question about RCA ANT702F.
Need a RCA ANT702F manual? We have 1 online manual for this item!

RCA Overview Questions Manuals Reviews Videos Research

Question posted by johnstineman49 on June 24th, 2014

In Line Amplifier To Boost Weal Signals On A Rca Ant702f Antenna

Where to install the in line amplifier on a Rca Ant702 f antenna, before the spliter or after

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related RCA ANT702F Manual Pages

User Guide - Page 1

... frequency energy and, if not installed and used in a particular installation. Caution: Any changes or modifications not expressly approved by one or more of the FCC Rules. Getting Started Remove the antenna and the hardware bag from package. Operation is no guarantee that may cause undesired operation. ENGLISH ANT702F Digital Ampliﬁed Indoor...

User Guide - Page 2

... (not included) WARNING: Never hang anything from the antenna; Mounting the Antenna The antenna mounting base and arm give you mount the antenna, consider the following factors in reception performance: • The antenna performs best when mounted vertically • The antenna should be . NOTES: Do not install the antenna on the side of your local broadcast towers. •...

User Guide - Page 3

... If you're mounting to the surface as shown here. You'll need to mount the antenna. • Set the base aside and drill a 0.1575" pilot hole at each hole ...not overtighten these screws, attach the base to concrete, brick, or drywall... Here's how to install them: • Place the antenna base against the concrete surface and secure it 's level. • Mark the surface through the ...

User Guide - Page 4

... the base's mounting well. Tighten the bolt to attach the arm to the arm. Attach the antenna to the base. 3. Tighten the bolt to attach the arm to the base. Attach the arm to the antenna. 4 First, set the bolt in this package. Find one of the well. Then position the arm...

User Guide - Page 5

...the U-bolts included in position. Find the coaxial cable and one of the antenna. Move the arm or antenna to a Mast 1. Re-tighten the bolt so that came with the cable's... IMPORTANT: If you 're using the coaxial cable that the antenna and arm stay ﬁrmly in this antenna, skip step 1. To adjust the antenna's position: 1. Connect the coaxial cable to the F-connector on...

User Guide - Page 6

.... Instead, leave it outside the U-bolt and tape it under the U-bolt. Important: These diagrams show the cable that the cable exits downward. 6 Position the antenna base as high as shown here. Note: If you want. Find the other U-bolt, the four washer nuts, the two clamps, and the...

User Guide - Page 7

... cable was designed to the mast. 5. First, set the bolt in the antenna's mounting well. Then position the arm over the other bolt included in this package.... DO NOT pass it to ﬁt under the U-bolt as shown here. Attach the antenna to the base. Tighten the bolt to attach the arm to the antenna as shown here. ENGLISH 4. Instead, leave it outside the U-bolt and tape it under...

User Guide - Page 8

... positions for best performance. 90° Important: These diagrams show the cable that the antenna and arm stay ﬁrmly in position. 6. Re-tighten the bolt so that came with the attached weather boot. To adjust the antenna's position: 1. Connect the coaxial cable to the mast. If you 're using a different cable...

User Guide - Page 9

... on the ampliﬁer to your splitter (splitter sold separately). DO NOT PUT THE SIGNAL SPLITTER BETWEEN THE AMPLIFIER INSERT AND THE ANTENNA. 3. The ampliﬁer insert should set this switch to split the signal coming from the antenna towards your television set. Plug it with a splitter for channels on your TV or...

User Guide - Page 11

... coverage (e.g. dated bill of sale), speciﬁcation of nature, alteration, improper installation, mishandling, misuse, neglect, or accident. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY...169;2013 VOXX Accessories Corporation 3502 Woodview Trace, Suite 220, Indianapolis, IN 46268 ANT702F NA IB 01 11 ENGLISH 12 Month Limited Warranty VOXX Accessories Corporation (the "...

RCA Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Can I use an XM® antenna with Sirius®, or vice versa?
.../2009 06:49 PM Blocked XM(R) and Sirius(R) satellite signals Satellite antenna inside a car Where can I place my antenna? Can I use an XM® antenna with Sirius®, or vice versa? In addition the XM® and Sirius® antennas use the wrong antenna, you use different amounts of electricity. If you will...
Troubleshooting the Jensen HD5112 Multi-Media Receiver
... size. Your iPod may need to be installed incorrectly. Why is "ERROR 1" displaying on...amplifier turn on lead. Make sure the session is slightly different from the amplifier when I switch between digital and analog signal...line of yellow and red wires with my unit? Make sure speaker wires are not connected properly. Note: The jlink3 cable is low signal level, relocate SAT antenna...
Troubleshooting the Jensen MP6212 Multi-Media Receiver
... RCA connectors from the amplifier when I switch between the radio source to my unit? Move into a clear line of correct rating and... on lead. Make sure power wire is low signal level, relocate SAT antenna. Why is mounted outside the vehicle on my unit?...displaying on my unit? Make sure speaker wires are solid and secure. Install fuse of sight. What is the volume very high or low when...