Poulan PR241 Support Question
Poulan PR241 Support Question
Find answers below for this question about Poulan PR241.Need a Poulan PR241 manual? We have 1 online manual for this item!
Question posted by hpaes55 on January 23rd, 2022
How Do I Replace Procedures To Change Drive Cable And Lever
Drive cable broke at lever up left bar. What is the disassemble and assemble procedures
Current Answers
Answer #1: Posted by SonuKumar on January 24th, 2022 8:09 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,619,310
Member since:
May 9th, 2021 Points: 16,619,310
https://www.youtube.com/watch?v=ZlebHaisvPo
https://www.youtube.com/watch?v=ZlebHaisvPo&t=82
https://www.youtube.com/watch?v=ZlebHaisvPo&t=108
https://www.youtube.com/watch?v=ZlebHaisvPo&t=169
https://www.youtube.com/watch?v=ZlebHaisvPo&t=192
https://www.manualslib.com/manual/854629/Poulan-Pro-Pr241.html?page=18
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Poulan PR241 Manual Pages
Owner Manual - Page 2
... is not possible, then refuel such equipment on clothing, change clothing immediately.
5. Disengage all units with the controls and...buildings. Do not use a nozzle lock-open device.
(g) Replace gasoline cap securely and wipe up , transporting, adjusting or making..., and when making repairs. Be thoroughly familiar with electric drive motors or electric starting motors.
6. Do not operate the...
Owner Manual - Page 6
... CONTROL
(See Figs. 6 and 7)
1. Tighten nut securely. Install all control lever knobs by pressing them down onto the control levers. Correct and equal tire pressure is important for shipping purposes. ASSEMBLY / PRE-OPERATION
INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 4 and 5)
1. Secure cables to chute deflector with discharge opening toward front of chute...
Owner Manual - Page 8
... Control -
used to engage auger motion (throw snow). used to change the direction the snow is thrown. used to adjust height of the American National Standards Institute. SAFETY REQUIREMENTS Our snow throwers conform to the engine. Drive speed control lever - Traction drive control lever -
must be inserted for shutting off valve -
Fuel shut off the...
Owner Manual - Page 9
...control lever.
• To change the discharge chute position, pull backward on discharge chute control lever and move lever forward...DRIVE
• Release traction drive control lever to stop the forward or reverse movement of the chute deflector. Always operate the snow thrower with the fuel shut-off valve is located beneath the fuel tank on chute deflector control lever and move lever left...
Owner Manual - Page 10
... in the engaged position. TRACTION DRIVE CONTROL LEVER
DRIVE SPEED CONTROL LEVER
AUGER CONTROL
LEVER
MOUNTING CLIP
FIG. 13
FIG. 14
10 Grasp the tool firmly by the drive speed control lever.
• Push right on the left side handle.
• Squeeze traction drive control lever to handle to engage the drive system.
• Release traction drive control lever to dislodge this blockage...
Owner Manual - Page 11
... caution and be emptied before requiring replacement. Adjust skid plates evenly to be cleared...CHANGE ENGINE OIL" in the Maintenance section of 30 days or longer. To avoid engine problems, the fuel system should be sure skid plates are empty. Adjust skid plates by the impeller, which leads to separation and formation of acids during storage.
Replace a damaged or worn scraper bar...
Owner Manual - Page 14
...
Install left wheel ...CHANGE ENGINE OIL
Determine temperature range anticipated before starting in a suitable container. Remove drain plug and drain oil in shortened engine life. Pour slowly. For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual.
9.
SPARK PLUG
Replace spark plug at "FULL" line on oil. We do not recommend using a garden... drive system...
Owner Manual - Page 15
...augers do not turn when auger control lever is secured to frame.
2. Install 1/4-... and left-hand augers are designed to break, preventing damage to stop .
2. To replace the...change direction and/or distance snow is in impeller hub with your snow thrower.
4. IMPELLER SHEAR BOLTS
The impeller is engaged, check to spark plug. To replace...BAR" in the Operation section of this manual.
Owner Manual - Page 16
...from fuel tank into a suitable container, outdoors, away from wear, they should fall during the belt changing process. Wipe up . REMOVE DISCHARGE CHUTE -
Remove upper 5/16" bolts and lower 1/4" bolts from...auger and traction drive belt be replaced. Move belt tensioner arm and place auger belt around the arm. NOTE: Ensure the belt is routed inside groove of the frame assembly.
3. Lift ...
Owner Manual - Page 17
... installed properly and that all controls to frame assembly.
7. Remove the top bolt holding the swing plate in this section. Place drive belt onto drive pulley. ENGINE PULLEY
ARM BOLT
PULLEY BOLT
DRIVE BELT TENSIONER ARM
TENSIONER SPRING
DRIVE PULLEY
DRIVE BELT
TOP BOLT
RETURN SPRING SWING PLATE
AFTER REPLACING BELT(S)
1.
Tire sealant also prevents tire dry...
Owner Manual - Page 19
... & carburetor, refill with fresh, clean gasoline. Carburetor is off valve to ON position). Loose parts or damaged augers or 1.
hard to a service center/department. Check / replace drive belt. 2. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
4. Loss of adjustment 5. Stale fuel.
3.
If vibration
impeller. Fill fuel tank with ice or 3. Prime...
Owner Manual - Page 25
... Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
25 MODEL PR241 (96192009201)
...CONTROL PANEL / DISCHARGE CHUTE
1
5
5
05.08.010-A
2
5
4
7 43 4
6
KEY NO.
1 2 3 4 5 6 7
PART NO.
587 80 34-01 581 32 94-01 877 10 08-12 532 42 33-03 584 65 22-01 586 68 21-01 587 13 08-01
DESCRIPTION
CABLE...
Owner Manual - Page 26
... PR241 (96192009201)
CONTROL PANEL / DISCHARGE CHUTE
6 8
1
37
4
2
4 5
05.08.011-B
KEY NO.
1 2 3 4 5 6 7 8
PART NO.
588 11 37-02 588 11 38-01 588 12 23-01 532 19 79-91 532 42 81-24 581 32 94-01 532 42 33-03 585 80 83-01
DESCRIPTION
CABLE CONTROL DRIVE CABLE CONTROL AUGER CABLE CONTROL...
Owner Manual - Page 27
MODEL PR241 (96192009201)
CONTROL PANEL / DISCHARGE CHUTE
KEY PART NO. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
27
inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. NO. REPAIR PARTS
SNOW THROWER - DESCRIPTION
3
3
2
1
587 33 25-02 CABLE INTERLOCK
2
532 43 17-62...
Owner Manual - Page 29
... PARTS
SNOW THROWER - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
29 LHS PIVOT, HANDLE LEVER - RHS LEVER, CONTROL LEVER, CABLE ARM - MODEL PR241 (96192009201)
CONTROL PANEL / DISCHARGE CHUTE
84 9
7
3 3
10
6 10 1
58
9
6
2
7
05.08.012...
Owner Manual - Page 30
NOTE: All component dimensions given in U.S.
REPAIR PARTS
SNOW THROWER - MODEL PR241 (96192009201)
CONTROL PANEL / DISCHARGE CHUTE
8 10
9 10 7
*11
*16
*13
*12
2
7...DEFLECTOR WELDMENT DEFLECTOR SEAL POP RIVET CHUTE SNOW SHIELD SHIELD STRAP RETAINER CABLE ASM DEFLECTOR BOWDEN PIN CLEVIS 5/16 X .875 PIN CLEVIS ... replacement parts. Failure to do so could be hazardous, damage your snow ...
Owner Manual - Page 32
REPAIR PARTS DRIVE
SNOW THROWER - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
32 MODEL PR241 (96192009201)
3 4
12
6 5
2
6
10
11
9
7
8
12 13
14
15
16 18
13 12
19
17
13
20
05.02.001-G
NOTE: All component dimensions given in U.S.
Owner Manual - Page 33
REPAIR PARTS DRIVE
SNOW THROWER - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. MODEL PR241 (96192009201)
KEY NO.
1 2 3 4 5 6 7 8 9 10 ... RUBBER WHEEL RING NUT HEX FLANGE LK 5/16-18 E-RING RETAINER 375 DRIVE SPACER DRIVE TORSION SPRING YOKE BRACKET ASSEMBLY FRICTION PULLEY DISC COMBO ROD TIP PLATE FRICTION SWING PLATE PULL LATCH SPRING NUT...
Owner Manual - Page 34
MODEL PR241 (96192009201)
6
1 2
6 4
3 2 1
05.03.001-B
8 7
3 5
5 3
KEY NO.
1 2 3 4 5 6 7 8
PART NO.
532 44 49-49...NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. REPAIR PARTS DRIVE
SNOW THROWER - Failure to do so could be hazardous, damage your snow thrower and void your warranty.
34
Owner Manual - Page 36
... inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. MODEL PR241 (96192009201)
CHASSIS / ENGINE / PULLEYS
3 2
2 1
4
4
05.04.002-B
KEY NO. 1
2
3 4
PART NO. 587 10 54-01
532 14 50-06
DESCRIPTION
BELT COVER BLACK ASSEMBLY (INCLUDES 2 & 4) BOLT HEX WSH THDRL 1/4-20 X 1 CABLE GUIDE PALNUT 1/4 IN
NOTE: All component dimensions given in...
Similar Questions
Manuel For Model # Pr20phst Riding Lawnmower
How do I replace the upper drive belt on the Polan Pro Model # PR20PH42ST riding lawnmower
How do I replace the upper drive belt on the Polan Pro Model # PR20PH42ST riding lawnmower
(Posted by dogboyadams 10 years ago)
Poulan Model P627es
auger lever handle will not remain engaged when drive control lever is engaged.
auger lever handle will not remain engaged when drive control lever is engaged.
(Posted by juanitalondon 10 years ago)
Are Their Anyway To Adjust Drive Belt? Replaced To Tight Wont Roll Locked Rear E
(Posted by martyc05 11 years ago)