Poulan P3816 Support Question
Poulan P3816 Support Question
Find answers below for this question about Poulan P3816.Need a Poulan P3816 manual? We have 1 online manual for this item!
Question posted by thomasjeff668 on March 5th, 2015
What Does The Gap Set On A Poulan 3816 Ignition Module
The person who posted this question about this Poulan product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by BusterDoogen on March 5th, 2015 4:57 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Air gap between coil and flywheel should be set at .012.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Poulan P3816 Manual Pages
User Manual - Page 2
... place wire where it cannot contact spark plug to move suddenly upward and backward, which may cause the guide bar to prevent accidental starting when setting up, transporting, ad- PLAN AHEAD S Read this manual carefully until the engine starts. safety chaps; Always use of accidents.
Push the choke/fast idle lever...
User Manual - Page 3
...object such as chain saw only in a cool, dry, well ventilated place; S Use only Poulan accessories and replacement parts as non-fogging, vented goggles or face
screen;
This contact can damage ...the engine stopped, hand carry the chain saw with the muffler away from your doctor before setting the saw from the
chain when the engine is a lightning fast, reverse reaction which kicks ...
User Manual - Page 5
... reactions may cause you to activation angle of chain break and resulting kick angle of kickback. Your saw has a low kickback chain and bar as set by pinching the saw chain along the top of the saw which could result in accordance with each other than those listed is a lightning fast...
User Manual - Page 6
... must monitor closely their physical condition and the condition of these parts. Computed kickback angle (CKA) Table
BAR
MODEL
P/N
Length CHAIN P/N
CKA without chain brake
P3816
530044748 16″
952051211
33_
NOTE: If this saw is to be used for commercial logging, a chain brake is required and shall not be removed...
User Manual - Page 8
... Lockout Rear Handle
Chain Brake
Adjusting Screw
Chain Direction of the various controls and adjustments. CHOKE/FAST IDLE LEVER The choke and fast idle are set by pulling the front hand guard back toward the front handle as far as possible.
CHAIN TENSION It is a device designed to the full extent...
User Manual - Page 9
... for adequate lubrication. BAR AND CHAIN LUBRICATION The bar and chain require continuous lubrication. Genuine Poulan bar and chain oil is a 3.2 ounce (95 ml) container of fuel lines, gaskets... engine performance and durability problems.
WARNING: Alternative fuels (not gas- Hold saw .
Poulan/WEED EATER brand synthetic oil is disengaged by smoke coming from someone that does understand ...
User Manual - Page 10
...In the following steps, when the choke/fast idle lever is pulled out to the ON posi- IGNITION SWITCH
ON STOP
Choke Lever
1. Pull the starter rope sharply 5 times with your right hand until... S When cutting with the saw is triggered. For cold weather starting procedure listed above.
To set automatically. then push the lever back in to idle speed. Squeeze and release throttle trigger to ...
User Manual - Page 11
... the notch.
11 S Allow the chain to cut , damage to reach full speed before reinstalling. Exert only
light downward pressure. S Carefully plan your saw before setting the saw . vance. S The lean of dirt and sand. Grip the rear handle with your right hand and the front handle with a flat file. Activate...
User Manual - Page 12
... . sharp
pieces of the felling cut
CUTTING A FALLEN TREE (BUCKING) Bucking is pinched or hung in the upper branches. S As tree starts to
fall completely, set the saw firmly and maintain control. See illustration. S Cut shattered wood very carefully; Stop the saw , put it is the term used for cutting a fallen...
User Manual - Page 14
... oil tank. Yearly Replace fuel filter . . . Yearly
* Hours of Operation -Each hour of operation is in this manual. GENERAL RECOMMENDATIONS The warranty on the product, Poulan may not pay for repairs under the saw after engine stops. Do not confuse this unit does not cover items that have been subjected to...
User Manual - Page 16
...spark ignition system complies with a 3/4 inch (19 mm) socket wrench. Remove the cylinder cover. 3. Replace with Champion RCJ--7Y spark
plug and tighten securely with the Canadian standard ICES--002. 1. Spark plug gap should ...plug should be forced through the cut you even when it is fixed and nonadjustable. Ignition timing is not moving. Loosen 3 screws on the top edges of the chain....
User Manual - Page 17
... following
steps after each use of the depth gauge tool. If you notice any sharp object cannot accidentally cause injury. The carburetor has been carefully set at idle speed. Adjustments may be necessary if you require further assistance or are using. See IDLE SPEED--T adjusting procedure. S Turn idle screw (T) clockwise to...
User Manual - Page 18
Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with new one season to
rust.
S Replace spark plug with fuel stabilizer.
Ignition switch off. 2. Fill tank with correct fuel mixture.
1. Check for loose screws, nuts,
and bolts.
Engine ... to insure proper blending of your gasoline can add a fuel stabilizer to oil ratio. Move ignition switch to distribute oil.
User Manual - Page 19
... the original date of purchase.
1 YEAR - U.S. Environmental
Protection Agency, California Air Resources Board, Environment Canada and Poulan are responsible for the performance of the required maintenance listed in your engine (as the carburetor, the ignition system and the fuel tank. In California, all products at no abuse, neglect, or improper maintenance of...
User Manual - Page 20
... CONTROL WARRANTY PARTS LIST: Carburetor, air filter (covered up to maintenance schedule), ignition system: spark plug (covered up to the owner if the part is responsible ...to
maintenance schedule), ignition module, muffler including catalyst (if equipped), fuel tank.
WHAT IS COVERED: REPAIR
OR REPLACEMENT OF PARTS.
WARRANTY PE- CONSEQUENTIAL DAMAGES: Poulan may be warranted ...
Similar Questions
Coil Specs
what are the ohm specs for testing the coil on a poulan p3314 chainsaw?
what are the ohm specs for testing the coil on a poulan p3314 chainsaw?
(Posted by 1969tralfaz 3 years ago)
Can Not Find A Replacement Ignition Module For Poulan Weed Eater Chain Saw P3314
(Posted by pattia1229 3 years ago)
I Get No Spark When I Try To Start My Poulan P3314 Ws Chain Saw
I have replaced the metal ground strap, the wires, the spark plug and the ignition module, and can't...
I have replaced the metal ground strap, the wires, the spark plug and the ignition module, and can't...
(Posted by elliotfnieves 8 years ago)
What Is The Points Gap Setting For Model P3416 Poulon Chain Saw
(Posted by jasonpowers81 8 years ago)
