Poulan DB24H42YT Support Question
Poulan DB24H42YT Support Question
Find answers below for this question about Poulan DB24H42YT.Need a Poulan DB24H42YT manual? We have 1 online manual for this item!
Question posted by kewheetv on April 15th, 2014
How To Remove Pin On The Deck Lift Lever Model Db24h42yt
The person who posted this question about this Poulan product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Poulan DB24H42YT Manual Pages
User Manual - Page 1
Failure to do so can result in U.S.A.
IMPORTANT MANUAL
Do Not Throw Away
02139
OPERATOR'S MANUAL
MODEL:
DB24H42YT
LAWN TRACTOR
WARNING:
Read this Manual and follow all Warnings and Safety Instructions. ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com
195021 Rev. 2 11.05.04 TR Printed in serious injury.
User Manual - Page 2
...up and thrown by the blades.
• Keep all times.
• Only allow the mower deck to cause cancer and birth defects or other reproductive harm.
• Do not operate machine without... discharged material toward the operator. Shut off blades, set parking brake, stop engine, and remove keys before and while back- Clean any oil or fuel spillage before storage. Allow machine to...
User Manual - Page 3
...allow extra distance to the machine and the mowing activity. Clean oil or fuel spillage and remove any adjustments or repairs with the engine running. • Check grass catcher components and ...; If fuel is clear of ignition.
• Use only approved gasoline container. • Never remove gas cap or add fuel with manufacturer's recommended parts, when necessary. • Mower blades are ...
User Manual - Page 5
...
Slope Sheet
(1) Hex nut 1/2-20 (1) Hex Bolt 1/4-28 x 1-1/4
(4) Retainer Springs Gauge Wheels
(double loop)
(4) Locknut 3/8-16 (4) Shoulder Bolt
(4) Wheels (4) Adjusting Bar
(4) Washers 3/8 x 3/4 x 14 Ga.
(4) Clevis Pins
5
User Manual - Page 7
...; Turn ignition key to "STOP" position.
TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)
• Press lift lever plunger and raise attachment lift lever to remove the tractor from the skid. Be sure the area in front of tractor is in Operation section of controls)
WARNING: Before starting, read...
User Manual - Page 8
...check to see "TO TRANSPORT" in the Operation section of this manual). RETAINER SPRING
PIN
SHOULDER
BOLT
ADJUSTING
BAR
GAUGE WHEEL
3/8 WASHER
FIG. 4
3/8-16 CENTER LOCKNUT
CHECK TIRE... System and Reverse Operation System (ROS) are routed correctly. ASSEMBLY
ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)
The gauge wheels are properly clamped.
✓ Before driving tractor, be...
User Manual - Page 9
...
UNLOCKED
OVER TEMP LIGHT
FUEL
OIL PRESSURE BATTERY REVERSE FORWARD
MOWER HEIGHT
15
MOWER LIFT
15
ATTACHMENT
ATTACHMENT
CLUTCH DISENGAGED CLUTCH ENGAGED DANGER, KEEP HANDS
AND FEET AWAY
KEEP... AREA CLEAR
SLOPE HAZARDS
(SEE SAFETY RULES SECTION)
FREE WHEEL (Automatic Models only)
LIGHTS ON
Failure to follow instructions could result in death, serious injury and/or...
User Manual - Page 10
... - Selects the speed and direction of mower deck or other attachments mounted to your tractor.
Save this manual for declutching and braking the tractor and starting the engine. CHOKE CONTROL
IGNITION SWITCH
THROTTLECONTROL
CLUTCH/BRAKE PEDAL
ROS "ON" POSITION
ATTACHMENT CLUTCH SWITCH
LIFT LEVER PLUNGER
ATTACHMENT LIFT LEVER
FREE WHEEL CONTROL
PARKING BRAKE
LIGHT SWITCH...
User Manual - Page 11
... attachment clutch switch to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.
• For best cutting performance, grass over... height is controlled by the operator to "STOP" position and remove key.
THROTTLE CONTROL
"BRAKE"
POSITION
02875
IGNITION KEY
MOTION CONTROL LEVER
TO USE CHOKE CONTROL (See Fig. 6)
Use choke control ...
User Manual - Page 12
...Remove retainer spring and clevis pin...LIFT LEVER HIGH POSITION
PUSH IN TO "DISENGAGE"
LOW POSITION
02876
DEFLECTOR
SHIELD
FIG. 8
REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with the engine running , turn ignition key counterclockwise to align holes in reverse unless absolutely necessary. Do not mow in bracket and gauge wheel bar and insert clevis pin...THE MOWER DECK. OPERATION...
User Manual - Page 13
...lever to bottom of this manual.
BEFORE STARTING THE ENGINE
When starting , read oil level. If the engine does not start after several attempts, push choke control in, wait a
few seconds, remove...leads to assure fuel freshness.
Use an appropriate means of tractor. • Raise attachment lift to highest position with a minimum of 87 octane. (Use of acids during storage....
User Manual - Page 14
... throttle control to half (1/2) speed. After the engine is running , move motion control lever to push the control in slowly.
• The attachments and ground drive can be ...transmission
should be warmed up period from dried clippings.
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
•...
User Manual - Page 16
...blades. BLADE REMOVAL (See Fig. 12)
• Raise mower to highest position to allow access to blades.
• Remove blade bolt... by the operator to be sharpened with trailing edge up towards deck as described, repair the problem immediately.
• The engine ...REPAIR PARTS. An unbalanced blade will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow ...
User Manual - Page 17
...a year if the tractor is not necessary.
Do not attempt to "leak" power. • Remove terminal guard. • Disconnect BLACK battery cable first then RED bat-
TRANSAXLE COOLING
The transmission... and after every 50 hours of the battery with the ground.
ENGINE
5/8" BOLT OR PIN
BLADE
LUBRICATION
Only use high pressure water or
steam to clean transaxle.
• Inspect ...
User Manual - Page 18
...engine or transmission will not run properly using a garden hose or pressure washer to clean your tractor. Use compressed air or a leaf blower to remove dirt and stubborn dried gum fibers.
CLAMP... drained completely, close and lock the
drain valve by pushing inward and turning clockwise until the pin is in the locked position as it could create a fire hazard and/or damage...
User Manual - Page 19
... belt off electric clutch pulley. • Disconnect anti-sway bar from chassis bracket by
removing retainer spring. • Disconnect suspension arms from rear deck brackets
by removing retainer springs. • Disconnect front links from deck by removing retainer
springs. • Raise lift lever to raise suspension arms. Slide mower
out from under tractor with plug. SERVICE AND...
User Manual - Page 20
... lift link adjustment nut on both front links an equal number of turns.
• When distance "D" is in all pulley grooves and inside all
belt guides. • Install mower in reverse order of mower, loosen nut "F" from bottom edge of removal...is in length. FIG. 19
FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21)
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. Tighten nut "E" on level surface.
User Manual - Page 22
... steps until tractor does not move mower deck height to allow
wheel removal (rear wheel contains a square key - If "jumper cables" are positioned straight forward, remove steering wheel and reassemble per instructions in ... right rear wheel, and lightly tighten.
• Start engine and move motion control lever until satisfied.
FRONT WHEEL TOE-IN/CAMBER
The front wheel toe-in neutral...
User Manual - Page 23
...lift off of tractor. • To replace, reverse above procedure.
• Lift hood to raised position.
• Remove terminal guard.
• Disconnect BLACK battery cable then RED battery cable and carefully remove... diagram in fuse.
Grasp hood at the factory and adjustment should not be necessary.
TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)
• Raise hood. • Unsnap ...
User Manual - Page 26
...connections. Poor cut - Replace blade mandrel. 5. Mower drive belt worn. 9. Clogged mower deck vent holes from buildup of mower housing. 8. Allow grass to open vent holes. Tighten ...connections. 3. Purge transmission.
Buildup of mower housing. 4. Tighten blade bolt. 2. Remove obstruction. 2. Replace mower drive belt. 3. Replace blade mandrel. Place throttle control in...
Similar Questions
Poulan Po15538lt Tractor Deck Lift
A pin which engages the lift lever to raise and lowere the deck is loose and engages the deck only i...
A pin which engages the lift lever to raise and lowere the deck is loose and engages the deck only i...
(Posted by naasirahmed42 2 years ago)
Pollen 42' Lawn Tractor. Model Po17542lt.
Can I purchase mower deck wheels for my mower deck (part no. 532 16 58-92)?
Can I purchase mower deck wheels for my mower deck (part no. 532 16 58-92)?
(Posted by lmccoy10 7 years ago)
Mower Decks
I have a Poulan model 96012004400 38" deck. I was wondering If I can not find the exact deck will an...
I have a Poulan model 96012004400 38" deck. I was wondering If I can not find the exact deck will an...
(Posted by bsrvar 11 years ago)