Panasonic EY7960 Support Question
Panasonic EY7960 Support Question
Find answers below for this question about Panasonic EY7960 - HAMMER DRILL 21.6V.Need a Panasonic EY7960 manual? We have 3 online manuals for this item!
Question posted by raijagdev on February 23rd, 2014
Need New Brushes For Ey7960 Motor
Where can I get brushes and how can I replace them
Current Answers
Related Panasonic EY7960 Manual Pages
EY7460 User Guide - Page 3
... hat, or hearing protection used to drill holes in wood and metal in moving parts. This enables better control of electric shock.
2) Avoid body contact with your main operated (corded) power tool and battery operated (cordless) power tool. Never modify the plug in hammer mode. Water entering a power tool will reduce risk of the power...
EY7460 User Guide - Page 4
...is dangerous and must be controlled with the switch is not in use .
Any power tool that cannot be repaired.
3) Disconnect the plug from the power source and/or the battery...and are caused by a qualified repair person using only identical replacement parts. Use of any adjustments, changing accessories, or storing power tools. Service
1) Have your application. III. Such preventive safety...
EY7460 User Guide - Page 5
...tool from bricks and
cement and other reproductive harm. min-1
Revolutions or reciprocation per minutes
Ah
Electrical capacity of battery pack
Forward rotation
Reverse rotation
Rotation with hammering Rotation only
WARNING:
Some dust created by power sanding, sawing, grinding, drilling...temperature rise and heat overload of the motor.
12) Do not drop the tool.
13) Wear dust mask, if the...
EY7460 User Guide - Page 6
..., oil and sharp edges.
21) Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with damaged cord or plug replace them immediately.
9) Do not... operate charger if it will not be used unless absolutely necessary. IV. Incorrect reassembly may reach or exceed 50°C (122°F) (such a metal tool shed, or...
EY7460 User Guide - Page 7
..., the battery contacts could be replaced by a repair shop appointed by turning the lock collar and tighten the screw (left-handed screw) with a keyless drill chuck. 1. Removal
Turn the ... ASSEMBLY
Attaching or Removing Bit
NOTE: When attaching or removing a bit, disconnect battery pack from the tool or the charger, always reattach the pack cover. This plug will fit in any way. Otherwise, ...
EY7460 User Guide - Page 8
...drilling. Depress the trigger switch slightly
to start the tool slowly.
- 8 - After use .
2. Check the direction of the trigger. A feedback electronic controller is released. 4. This is released and the motor stops immediately. Tighten Loosen
Remove the handle when placing the tool... work, depress the trigger slightly to start the tool slowly. 3. Push the lever for forward rotation....
EY7460 User Guide - Page 9
...motor.
* See specifications for confirming the tightness of the 18 clutch settings or " ", " " position (EY7960).
The tool needs cool-off time before switching to cause a failure.
• Do NOT strain the tool (motor).... make sure to one of the tool and disengage it from the work, when you select Hammering mode from Drilling mode or when you may cause a motor breakdown.)
- 9 - LOW
HIGH...
EY7460 User Guide - Page 10
... for a regular flashlight, since it does not have enough brightness. • LED light turns off when the tool has not been used in hazardous radiation exposure.
(2) Overheat warning lamp
Off (normal operation)
Illuminated: Overheat (motor)
Flashing: Overheat (battery)
Indicates operation has been halted due to flash.
• If you notice the battery...
EY7460 User Guide - Page 11
...Please call 1-800-8-BATTERY for example, immediately after recharging, replace the battery pack with a new one hour to prevent overcharging. • Charging will automatically...batteries have purchased. Li-ion Battery Pack
NOTE: Your battery pack is below 0°C (32°F), the tool may be triggered to warm up the alignment marks and place the battery onto the dock on the charger ...
EY7460 User Guide - Page 13
SPECIFICATIONS
MAIN UNIT
Model Motor voltage No load speed
Blows Rate Per Minute Chuck capacity
Low High Low High
Clutch torque
Overall length Weight (with battery pack: EY9L60)
EY7460
EY7960
21.6 V DC
100 -... lbs)
- 13 - APPENDIX
MAXIMUM RECOMMENDED CAPACITIES
Model Screw driving
Drilling
Machine screw Wood screw Self-drilling screw For Wood For Metal For Masonry
EY7460 --- M8 ø...
EY7460 User Guide - Page 14
EY9201 EY9231 55 min.
18 V
EY9251 65 min.
24 V
EY9116 EY9117 60 min. Please refer to the latest general catalogue.
- 14 - Full: 50 min.
21.6 V EY9L60 Usable: 45 min.
EY9210 90 min. EY9200 EY9230 45 min. Full: 70 min.
[Ni-Cd/Ni-MH battery pack]
1.2 Ah
7.2 V
EY9065 EY9066
Charging time
1.7 ...
EY7460 User Guide - Page 44
PANASONIC CONSUMER ELECTRONICS COMPANY
One Panasonic Way, Secaucus, New Jersey 07094
No.1 EN, FR, ES EY981074601 H2009
Printed in China
Service Manual - Page 1
... Guide 3 4 Disassembly and Assembly Instructions 6 5 Wiring Connection Diagram 10 6 Schematic Diagram 10 7 Exploded View and Replacement Parts List -----------11
PAGE
© Panasonic Electric Works Co., Ltd. 2008. Unauthorized copying and distribution is a violation of law. All rights reserved. Order Number PTD0810X45CE
Cordless Drill & Driver Cordless Hammer Drill & Driver
Model No.
Service Manual - Page 4
Q for EY7960 only 4
Service Manual - Page 6
... wrench into the chuck, and turn the chuck fastening screw inside the chuck clockwise direction of the Keyless Drill Chuck.
1. Fig. 2 Fig. 3
6 No. 1A Procedure 1A
Fig. 1
Removal of the ... Keyless Chuck. Insert the allen wrench into the chuck and lightly tap in the arrow with a hammer to position 1 and select "LOW" position. 2. Ref. 4 Disassembly and Assembly Instructions
4.1. Set...
Service Manual - Page 7
...1. Ref.
Remove the support handle. (See Fig. 4). 2. Take out the motor with Shell Alvania for assembly. (See Fig. 6)
Fig. 4
Fig. 6
Fig. 5
Ref. No. 2A Procedure ...2A
Removal of the Motor.
(Removal) 1. Remove nine housing screws. (See Fig. 5). How to unlock tabs. (See Fig. 7)
(Attachment) Motor mounting base and the positioning rib of housing with the ...
Service Manual - Page 8
EY7960
(Removal) 1. Set the E-type ring. 2. The internal parts of gear box block can be removed one of each as shown in the Fig. 9. 2. NOTE:
Carrier, ...
Service Manual - Page 12
...AB SET CHUCK FASTENING SCREW KEYLESS CHUCK CLUTCH HANDLE H/L CHANGE HANDLE F/R SELECTOR HANDLE SEMS SCREW DC MOTOR SEMS SCREW SWITCH CONTROL PCB OPERATION PANEL TORX TAPPING SCREW GEAR BOX BLOCK SUPPORT HANDLE BATTERY PACK COVER TOOL CASE OPERATING INSTRUCTIONS
Q'ty
Remarks
1 (for EUROPE), 1 (for OCEANIA), 1 1 1 1 1 2 (K3*6) 1 2 (K5*6) 1 1 1 9 (K3*20) 1 1 1 1 1
Model No...
Service Manual - Page 14
... HANDLE F/R SELECTOR HANDLE SEMS SCREW DC MOTOR SEMS SCREW SWITCH CONTROL PCB OPERATION PANEL TORX TAPPING SCREW GEAR BOX BLOCK SUPPORT HANDLE BATTERY PACK COVER TOOL CASE OPERATING INSTRUCTIONS
Q'ty
Remarks
1 (for EUROPE), 1 (for OCEANIA), 1 1 1 1 2 (K3*6) 1 2 (K5*6) 1 1 1 9 (K3*20) 1 1 1 1 1 EY7960
Part No.
1 WEY7960K3079
1 WEY7960K3070
2 WEY6450L6806
3 WEY6450K7915...
Parts List - Page 2
... CHUCK H/L CHANGE HANDLE F/R SELECTOR HANDLE SEMS SCREW DC MOTOR SEMS SCREW SWITCH CONTROL PCB OPERATION PANEL TORX TAPPING SCREW GEAR BOX BLOCK SUPPORT HANDLE BATTERY PACK COVER TOOL CASE OPERATING INSTRUCTIONS
Q'ty
Remarks
1 1 1 1 1 2 (K3*6) 1 2 (K5*6) 1 1 1 9 (K3*20) 1 1 1 1 1 EY7960
Part No.
1 WEY7960K3078
2 WEY6450L6806
3 WEY6450K7915
4 WEY7460H3238
5 WEY7460H3248...
Similar Questions
Need New Speakers For Sa Ak58. Coming Up With Nothing Anywhere??
(Posted by mariacooke51794 9 years ago)
Ey7880 Drill
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would c...
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would c...
(Posted by neilcooper2000 10 years ago)
Need New Remote Control For Old Tv Model Pv-df275. Is One Available
(Posted by sylyal 10 years ago)
Need New Ricecooker Bowl.
How/where do I buy new rice cooker bowl for Panasonic SRMM10 NS which is working fine?
How/where do I buy new rice cooker bowl for Panasonic SRMM10 NS which is working fine?
(Posted by bhilty 11 years ago)
Need New Steam Cap
Need new steam cap for Panasonic PANASONIC SR-TMB10
Need new steam cap for Panasonic PANASONIC SR-TMB10
(Posted by laserwiz 12 years ago)