Panasonic 1100W Support Question
Panasonic 1100W Support Question
Find answers below for this question about Panasonic 1100W - Sharp 1 CF Microwave.Need a Panasonic 1100W manual? We have 1 online manual for this item!
Current Answers
Related Panasonic 1100W Manual Pages
Service Manual - Page 1
...SIMMC 0001002C1
E1
Service Manual Microwave Oven
Specifications for CPH:
Specifications: Power Source: Power Requirement: Output(IEC705-88): Microwave Frequency: Timer: Outside Dimensions: Oven Cavity Dimensions: Weight:
Model: NN-S560BF/WF NN-S540BF/WF NN-L530WF NN-L520WF NN-S510WF
*120V AC Single Phase, 60Hz
1370W
1370W
1370W
1370W
1200W
1100W
1100W
1100W
*2450MHz *99min.99sec *20...
Service Manual - Page 2
...
SCHEMATIC DIAGRAMS 7 TROUBLESHOOTING GUIDE 20
DESCRIPTION OF OPERATING SEQUENCE 9 EXPLODED VIEW AND PARTS LIST 24
CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING ....11 SCHEMATIC DIAGRAM &
PARTS LIST OF DIGITAL PROGRAMMER CIRCUIT 25
-1- Though this service information by trained, qualified personnel.
2. There are special components used in the microwave oven which are marked...
Service Manual - Page 3
... (RECTIFIER BRIDGE)
CHOKE COIL CURRENT
TRANSFORMER SAND BAR RESISTOR
HIGH VOLTAGE TRANSFORMER
GROUNDING
PLATE * 4
PCB
DO NOT TOUCH
FILM CAPACITORS
VARISTOR
PRIMARY WINDINGS SECONDARY WINDINGS HIGH VOLTAGE DIODES
- 2 -
Very high voltage may remain in ordinary microwave ovens.
2. 3. Inverter Circuit (U) with original shipping box and shipping materials.
It is very hot...
Service Manual - Page 5
... process. Another tap cancels all your instructions. If door is opened or STOP/RESET Pad is pressed once during
oven operation, START Pad must again be pressed to begin functioning. NN-S540
CONTROL PANEL
NN-L530
NN-L520
1
...12) More /Less Pad (13) Cooking Guide (14) Auto Cook Pad (15) Serving/Weight Pad (16) Start Pad
One tap allows oven to restart oven.
(17) Stop/Reset Pad
Before cooking: ...
Service Manual - Page 6
... of day (TOD) by pressing Number pads. 1 lb = 1 0
1.0
3. Press Start pad. Auto Cook OPERATION
1. If you pluge the power supply cord into the wall outlet, microwave oven automatically enter into the digital programmer circuit and will count up by pressing Number pads. 1 min.= 1 0 0
1.0 0
6. Press Inverter Turbo Defrost pad. OPERATION AND DIGITAL PROGRAMMER...
Service Manual - Page 10
...- NOTE: The ON/OFF time ratio does not correspond with the
percentage of the microwave oven is tapped: (A) The digital programer circuit determines the power level and cooking
time to ...Start Pad is as the H.V.
Table shows the corresponding cooking times for heating of the microwave oven from the current transformer built into the inverter ciruit. 6. transformer, the H.V.capacitor and...
Service Manual - Page 11
...Sensor Cooking, a carefully designed instrument, called T2 time, can be prepared in the Auto Sensor Cooking Guide. Example of cooking time which is selected, the K factor varles resulting In T2 time to T2 ...to cook by the following tables along with the foods and
recipes found in the microwave oven using the formula below make sure this 10 second is a revolutionary way to select...
Service Manual - Page 12
... charge in their watches whenever working close to have a proper chassis ground by the grounding plate and screws. Servicemen should be taken during operation. therefore, extreme care should be taken during...may be HOT from the outlet. CAUTION
WARNING Never touch any other appliances, the microwave oven is blown due to the operation of short switch:
make sure to touch chassis ...
Service Manual - Page 13
... sure that the screws of the
oven, etc. After repair or exchange, it is very important to check if magnetron and the door hinges are tight before inserting the plug into the wall outlet. (C) Check for microwave energy leakage. (Refer to procedure for measuring microwave energy leakage.)
CAUTION MICROWAVE RADIATION DO NOT BECOME EXPOSED...
Service Manual - Page 14
... and shown on page 11. (B) Remove 1 screw holding air guide c to magnetron. (C) Disconnect 2 high voltage lead wires from magnetron..., as using a hair dryer is attached to prevent microwave leakage.
The membrane key board is recommended for smoother... 2 catch hooks on oven attaching orifice assembly. (C) Remove orifice assembly/Inverter power supply (U) from oven assembly. (Refer page 15...
Service Manual - Page 15
...Remove the door from tabs on sensor mounting plate and air guide. (E) Remove steam sensor from sensor mounting plate. If door is misaligned, apply pressure
until...: After breaking off the motor cover, make sure that no sharp edge will expose to outside. (B) Disconnect 2 lead wires connected...microwave leakage test.
6.
After replacement of the defective component parts of steam sensor...
Service Manual - Page 16
8. Remove screw
3. Detach turntable wires
from the
oven. Retighten 2 screw 10. Securely connect 3 lead wire connectors. 4. Take off outer panel....
8. Disconnect all wires to securely tighten grounding screw from inverter. Replace inverter and reassemble to leave the grounding plate in its place. 2. Slide and place assembly to the correct location of the base slightly
2. Make sure to...
Service Manual - Page 19
... hook assembly as shown in the door by performing IEC standard test procedures. Measurement of microwave output
The output power of Primary latch switch, Secondary latch switch and Short switch.
... Check for each model is blown due to the oven assembly.
(C) Reconnect the short switch and check the continuity of glass cook plate. Primary latch switch and the short switch. A61785180AP, ...
Service Manual - Page 20
...replaced or adjusted.
PROCEDURE FOR MEASURING MICROWAVE ENERGY LEAKAGE
WARNING Check for radiation leakage after measurement
(A) After any adjustment or repair to a microwave oven, a leakage reading must be ...leakage reading must be kept by repair facility. Record this repair ticket and the microwave leakage reading should initially be more than 1 inch/sec (2.5cm/sec). (3) Leakage...
Service Manual - Page 21
...is dead. Be careful of any static charge in your meter. First of all operate the microwave oven following the correct operating procedures in with the AC plug removed.
SYMPTOM
1. Shorted lead wire ... circuit of power relay B (RY-1) 5. TROUBLESHOOTING GUIDE
CAUTION
1. Off-alignment of secondary latch switch 3. Off-alignment of latch switches 2. Open thermal cutout (Cavity...
Service Manual - Page 23
...H97, H98, or H99 appears in display window a short time after start key is pressed and no microwave oscillation. Alternate way to determine a good magnetron.
- 22 - NOTE: DO NOT try to repair ... may be replaced with a self diagnostics failure code system which will flow
STOP! This oven is dangerous. H97, H98, H99 appears in display window
Check magnetron filament continuity
Open
...
Service Manual - Page 24
...on even though the program has been set and the start pad is tapped
No microwave oscillation at high power
Q220 transistor
Replace display and check operation
Replace IC-1 and check... conduct following test quickly, unless H97/H98 appears and oven stops. Latch Switch 2.
Program High power for the presence of ZNR, L.V.T., Oven Lamp etc. Oven is dead.
NEW H.V. STEP 1
CHECK Fuse pattern...
Service Manual - Page 26
...PLATE NAME PLATE NAME PLATE NAME PLATE NAME PLATE BASE
Pcs/ set
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks
******APH ******CPH S560BFAPH S560WFAPH S560BFCPH S560WFCPH S550BFAPH S550WFAPH S540BFAPH S540WFAPH S540BFCPH S540WFCPH L530BFAPH L530WFAPH L530WFCPH L520WFCPH S510WFCPH
4
F10084T00AP
RUBBER FOOT
5
F110D4T00BAP
CABINET BODY (U)
5
F110D4T00HAP
CABINET BODY (U)
6
F201A4T00AP
OVEN...
Service Manual - Page 27
... F41444T00AP F64505540AP
Part name & Description
FAN MOTOR FAN BLADE AIR GUIDE A ORIFICE EXHAUST GUIDE B
Pcs/ set
1
1 1
1 1
Remarks
AC120V, SINGLE...*FAPH
1
S540*FCPG, L530WFCPH,L520WFCPH,S510WFCPH
B62308250AP B62314000AP F61844T00AP B63264080AP F900C9660AP F900C9660CP
FUSE FUSE HOLDER GROUNDING PLATE TURNTABLE MOTOR AC CORD W/PLUG AC CORD W/PLUG
1
18A/120V,60Hz
1
******APH
1
1
...
Service Manual - Page 36
Part name & Description Pcs/ Set
Remarks
F00074T20BRP NAME PLATE
1 NN-S540BF
F00074T20HRP NAME PLATE
1 NN-S540WF
F00074T70BRP NAME PLATE
1 NN-540BF
F00074T70HRP NAME PLATE
1 NN-540WF
F603L4T70RP D.P.CIRCUIT
1 NN-S540BF/WF, NN-540BF/WF
F603Y4T20BAP MEMBRANE SWITCH(U)
1 NN-S540BF
F603Y4T20HAP MEMBRANE SWITCH(U)
1 NN-S540WF
F603Y4T70BRP MEMBRANE SWITCH(U)
1 NN-540BF
...
Similar Questions
Microwave Glass
Wnere can I get a new glass bottom for my microwave?
Wnere can I get a new glass bottom for my microwave?
(Posted by kstiland 10 years ago)
Panasonic Nn-h765bf Microwave Purchased 2008 Troubleshooting.
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
The time display is on but the microwave turns off in few secs. Please help me fix this issue. It wo...
(Posted by Kamathn 11 years ago)
My Connectionless Steamer Microwave Oven Ne-2180 Does Not Work Fuses Replaced
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
my Sonic Steamer Connectionless Steamer Microwave Oven - NE-2180 keeps blowing the 20a /250v fuse in...
(Posted by sbenson99 11 years ago)
Nn-s530bfv Microwave Worked, Now Runs For 4 Seconds When Turned On.
the NN-S530BFV microwave worked fine to bake potatoes and now it will only run for 4 seconds and c...
the NN-S530BFV microwave worked fine to bake potatoes and now it will only run for 4 seconds and c...
(Posted by Hambydv 12 years ago)