Oreck Platinum Pilot Support Question
Oreck Platinum Pilot Support Question
Find answers below for this question about Oreck Platinum Pilot.Need a Oreck Platinum Pilot manual? We have 1 online manual for this item!
Question posted by PKELL911 on November 7th, 2012
Oreck Vacuum Model #xl2800h2 Remove+ Replace Motor Where Do The Plugin Wires Go?
The person who posted this question about this Oreck product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Oreck Platinum Pilot Manual Pages
Owners Guide - Page 1
79052-01 REV A
User's Guide
Powerful, Lightweight Upright Vacuum
ORECK XL® Platinum Pilot ™ Series
Important!
Microban® is a registered trademark of Microban Products Company Corporation, North Carolina. Read all instructions carefully, and keep for future reference.
Owners Guide - Page 2
... up anything that may be present. • Do not use with wet hands. • Do not put any period of -the-line Oreck XL® U7200 Platinum Pilot™ Series upright vacuum cleaner. When using an electrical appliance, basic precautions should , has been dropped, damaged,
left outdoors, or dropped into the longest socket slot...
Owners Guide - Page 3
To assist you in identifying your vacuum's components, the parts have been numbered as follows.
ENGLISH
......5
Maintenance ...6 Replacing Disposable Odor Fighting Dust Bag 6 Replacing Worn Belt ...6 Adjusting or Replacing Brushroll 6 Replacing Edge Brush ...7 Replacing the LED Light ...7 Stuffing or Blockage ...7
Troubleshooting ...8 Parts ...8
Accessories & Replacement Parts 8 Warranty ...
Owners Guide - Page 4
... during use . Operating Instructions
This new ORECK Upright is one stationary position for any period...vacuum cleaner on handle assembly when ready to engage lock. Damage caused by carry handle on a sturdy fastener or Helping Hand® handle on back of cleaner. For optimal performance, replace... carry handle can be
removed from the floor before returning to the motor suction fan and its...
Owners Guide - Page 5
...Oreck belts will not operate the revolving brush correctly and may create undue stress which will void the warranty. Lubrication
The vacuum cleaner motor bearings are not the same. Further lubrication is dust in any
one stationary position for replacing...clogged, no air can be cleaned.
To keep them handy for and remove excessive lint, string or hair from revolving brush. DO NOT FILL ...
Owners Guide - Page 6
... pulley. Place the opposite end of the belt on the motor drive shaft. 18 Replace the door by removing the hold down screw located on indication point until it away. 16 Remove the belt from the power head and lift it snaps. Your Oreck Vacuum comes with both end card assembly settings are the same and...
Owners Guide - Page 7
... the air flow system. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up , remove the screw located in the area where...counterclockwise to back down until the tube is blockage, remove it fails to the connector assembly. If there is seated. Replace tube by an Oreck authorized service center whenever it with tab inside the ...
Owners Guide - Page 8
... Canada: 1-888-676-7325 website: www.oreck.com
shooting
Service problems that appear to be major can be your model number from the data label on the bottom of the unit. You can often be done by
reviewing this guide. fuse or circuit breaker. See "Replacing Disposable Odor Fighting Dust Bag". • Clear...
Owners Guide - Page 9
...your purchase is valid only if you retain proof of expendable or consumable parts such as carbon motor brushes, edge brushes, drive belts, brushes, bulbs, disposable bags and other than indicated on ...This limited warranty does not cover the replacement of purchase from state to the amount paid for this product at the time of original purchase, and Oreck shall not be defective in material ...
Owners Guide - Page 28
All rights reserved. ©2009 Oreck Holdings, LLC. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC.
79052-01 REV A 11/09 ECN# R-9554
Similar Questions
How Do I Get The Bottom Off On This U8000 Model To Replace The Belt?
(Posted by Consultalp 10 years ago)
How Do I Replace The Wire That Goes Over The Brushroll?
THe wire covering the brushroll came off removing baseplate to clean. How do i replace it?
THe wire covering the brushroll came off removing baseplate to clean. How do i replace it?
(Posted by thekeach 11 years ago)
Have Johnson Replacement Motor For Oreck Xl Need Wiring Help
(Posted by psterling2 12 years ago)