Netgear WNR1000 Support Question
Netgear WNR1000 Support Question
Find answers below for this question about Netgear WNR1000 - RangeMax 150 Wireless Router.Need a Netgear WNR1000 manual? We have 5 online manuals for this item!
Question posted by danand1304 on September 8th, 2012
Unable To Login Even After Default Password And Reseting The Wnr1000v2.
I tried all the options. The deafult password as password, the older password as 1234. The factory reset option with 5, 10 and 20 sec all of it with no luck. All the basic connection settings are ok and lights blinking is fine not able to get through. This is new router I got today
Current Answers
Related Netgear WNR1000 Manual Pages
WNR1000 Setup Manual - Page 22
...
A LAN light should be lit for each connected computer on . If a LAN light is communicating at 10 Mbps.
See "Restoring the Default Password and Configuration Settings" on page 39 for Internet Access
When configuring your wireless router manually, you must log in to your computer is not lit for each connected Ethernet cable, make sure that the Ethernet...
WNR1000 Setup Manual - Page 34
When power is on (see "Connecting Your Wireless Router" on page 39. After approximately 20 seconds, verify that the power light is first applied, verify that :
a. If a port's light is connected to the instructions in "Restoring the Default Password and Configuration Settings" on page 14), check the following:
- Check that you are off ).
If a LAN port is lit, a link...
WNR1000 Setup Manual - Page 36
...and advanced features, see "Restoring the Default Password and Configuration Settings" on page 14 for help with the wireless router. The factory default login name is admin and the password is on page 41 for instructions. Refer to the factory defaults.
If your computer. If you don't know the current IP address, reset the router's configuration to your computer's documentation or...
WNR1000 Setup Manual - Page 43
This procedure will be restored so that reset the router's user name to admin, the password to password, and the IP address to 192.168.1.1.
To restore the factory default configuration settings:
1. Technical Specifications
39
Release the restore factory settings button, and wait for the router to restart, and for the Power light to blink (see "Back Panel" on the rear...
WNR1000 User Manual - Page 16
... Basic Connectivity
v1.0, January 2009
Note: The router user name and password are not the same as any other user name or password you must type the IP address of the router, for the router user name and your password (or the default, password). A login window displays. Figure 1-1
Tip: You can access and configure the router using your browser. N150 Wireless Router WNR1000...
WNR1000 User Manual - Page 46
...will have to reset the router back to the factory defaults, and log in your settings, see "Backing Up and Restoring the Configuration" on page 6-6. N150 Wireless Router WNR1000 User Manual
Now, only devices on this password to a more secure password.
On the main menu, under Maintenance, select Set Password to re-enter all the router configuration settings. Figure 2-13 2-20
v1.0, January...
WNR1000v2 Setup Manual - Page 20
...or http://www.routerlogin.com. A LAN light should be lit for each connected computer on . See "Restoring the Default Password and Configuration Settings" on .
A login window similar to your wireless router's settings later. amber indicates communication at 100 Mbps; Setting Up Your Router for more information. Status Lights After Installation (continued)
Label 4.
Type http://www...
WNR1000v2 Setup Manual - Page 34
Troubleshooting Login Problems
If you are unable to log in to the factory defaults. If you don't know the current IP address, reset the router's configuration to the wireless router, check the following:
• If you are using an Ethernet-connected computer, check the Ethernet connection between the computer and the router as the router. Try closing the browser and reopening it again. ...
WNR1000v2 Setup Manual - Page 39
... Settings
Feature
Default Setting
Router Login
Router Login URL
http://www. Technical Specifications
Default Configuration Settings
This section provides factory default settings and technical specifications for
the Internet)
traffic on port 80, the http port)
Outbound (communications going out to Enabled (all unsolicited requests except for the Wireless-N 150 Router Model WNR1000v2...
WNR1000v3 Setup Manual - Page 21
... attached at 10 Mbps. See "Restoring the Default Password and Configuration Settings" on your wireless router manually, you use the Restore Factory Settings button.
Status Lights After Installation (continued)
Label 4.
Setting Up Your Router for Internet Access
When configuring your network.
Manually Installing Your Router
16 If a LAN light is not lit for each connected computer...
WNR1000v3 Setup Manual - Page 33
...-connected computer, check the Ethernet connection between the computer and the router as the router.
Troubleshooting Login Problems
If you are unable to log in "Checking Basic Router Functions" on page 35 for instructions. If your IP address is in the range 169.254.x.x. Troubleshooting
27
Make sure that you have a good connection from the computer to the factory defaults...
WNR1000v2 User Manual - Page 16
... IP address of the router, for the router user name and your password (or the default, password).
Enter admin for example, http://192.168.1.1.
2. Wireless-N 150 Router WNR1000v2 User Manual
Logging In To Your Wireless Router
When the wireless router is printed on the bottom label of your router. The Default Access login information is connected to the wireless router by typing either of...
WNR1000v2 User Manual - Page 22
Wireless-N 150 Router WNR1000v2 User Manual
- Note: If you enter or change the MAC address, select one ... router to the router during login, select Use These DNS Servers, and enter the IP address of that computer by the ISP.
- If your account is allowed by "cloning" or "spoofing" its MAC address. The gateway is available, enter it here.
1-8
Configuring Basic Connectivity...
WNR1000v2 User Manual - Page 24
... with Telstra DSL accounts and newer cable modem accounts should select No for older cable modem service accounts still requiring a Bigpond login utility. If your ISP. Service Name. The list includes:
Figure 1-9
• Always On. Wireless-N 150 Router WNR1000v2 User Manual
• Internet Service Provider. Connection Mode. Not all ISPs are used primarily in to multiple Internet...
WNR1000v2 User Manual - Page 30
... wireless security settings. Default passwords are well known, and an intruder can use your router. Figure 2-1
To configure the wireless network, you change the administrator password, see "Changing the Administrator Password" on page 2-4). For information about how to establish. Wireless Settings. Advanced Wireless Settings. Wireless-N 150 Router WNR1000v2 User Manual
WEP connections...
WNR1000v2 User Manual - Page 48
... Control On, you lose your wireless connection when you want to add to save the settings with the default password of password. Click Apply to the list. 7. Changing the Administrator Password
The default password for each additional device you click Apply. For information about how to the Wireless Card Access List. Wireless-N 150 Router WNR1000v2 User Manual
5. However, because...
WNR1000v2 User Manual - Page 49
...Configuration
The configuration settings of password.
Safeguarding Your Network
v1.0, September 2009
2-21
Figure 2-13
2. Wireless-N 150 Router WNR1000v2 User Manual
To change it later. On the main menu, under Maintenance, select Set Password to the factory defaults and log in using the default password of the WNR1000v2 router are stored within the router in a configuration file...
WNR1000v2 User Manual - Page 85
...connection is compatible with older 802.11b and 802.11g adapters, the use RangeMax NEXT adapters such as the WN511B for speed, economy, and security. Fine-Tuning Your Network
v1.0, September 2009
5-17 Your Wireless-N 150 Router Model WNR1000v2 provides a wireless...As gigabit-speed Ethernet ports (10/100/1000 Mbps) become common on the same network with older-generation XE family products or ...
WNR1000v2 User Manual - Page 94
... use the restore factory settings button on the rear panel of the router (see "Restoring the Default Configuration and Password" on your router's configuration settings. When you will need to reset the configuration to the file. If you forget the password, you have saved the configuration file. Warning: Do not interrupt the reboot process. Wireless-N 150 Router WNR1000v2 User Manual
The...
WNR1000v2 User Manual - Page 114
... 6-8. • Use the restore factory settings button on page 5-14.
Wireless-N 150 Router WNR1000v2 User Manual
• Is your router set to a wireless standard that is not supported by objects between the router and your adapter? Check the Mode setting as a pen or a paper clip to press and hold the restore factory settings
button for cases
when the administration password or IP address is...
Similar Questions
Default Password
Please could you tell me the default password for Netgear WNHD3004
Please could you tell me the default password for Netgear WNHD3004
(Posted by mpadova 7 years ago)
What Is The Default Password For Netgear Wnr1000v2
(Posted by JJJ06gle 10 years ago)
How Can I Change The Netgear Wnr1000v2 Default Password
(Posted by Bastrdap 10 years ago)
How To Connect Comcast Modem To Netgear Wnr1000 Rangemax 150 Wireless Router
(Posted by rakdoug 10 years ago)
Why Does It At Times Ask For User Login And Password When None Are Created, W7
using windows 7 at one time I can log in with no issues and other times it asks for user name and pa...
using windows 7 at one time I can log in with no issues and other times it asks for user name and pa...
(Posted by lucjang 12 years ago)