Home » Maytag » Laundry Washers » Maytag MVWC200XW

Maytag MVWC200XW Support Question

Find answers below for this question about Maytag MVWC200XW.
Need a Maytag MVWC200XW manual? We have 3 online manuals for this item!

Maytag Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-49369 on January 24th, 2012

Lights Blinking

What does it mean when the spin cycle and lid locked lights are blinking. During this time the machine is completely stopped. So far its happened twice and I've had to cancel the cycle in order to stop it. Your response would be appreciated.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Maytag MVWC200XW Manual Pages

Installation Instructions - Page 2

... parts before starting installation. Beaded tie strap Drain hose with clamp Inlet hoses with flat washers To order, please refer to toll-free phone numbers on back page of the washer. n 8212656RP n 8212641RP n 8212646RP n 8212545RP n 8212487RP n 8212638RP n 8212637RP 10 ... are in cardboard insert in a basement, laundry room, closet, or recessed area. 271/2" 27" (648 mm) (686 mm) 42" (1067...

Installation Instructions - Page 3

... of washer. (Additional hoses may be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. install no higher than 4.5" (113 mm) of drain hose should be exposed to 120° F (49° C). DRAIN SYSTEM Drain system can be purchased separately. install no more space for ease of wash tub. To order...

Installation Instructions - Page 4

... properly grounded. A time-delay fuse or circuit breaker is required. n This washer is the personal responsibility and obligation of its final location; If a mating outlet is not available, it and make sure lid is taped shut. 2. n Do not have a fuse in the neutral or ground circuit. 48" (1.2 m) Move washer to within 4 ft (1.2 m) of the customer...

Installation Instructions - Page 5

... step 6. Gently place power cord over side of laundry tub. do not force excess hose into standpipe (shown in Step 7. NOTE: Keep tray in standpipe Drain hose form Firmly grasp power cord plug and pull to drain port Remove tape from washer lid, open lid and remove cardboard packing tray from tray. For a floor...

Installation Instructions - Page 6

...until it is seated on water faucets to check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to water faucets Run water for leaks. Repeat with second hose ...faucet, you are found. 11. Water should run until clear. 10. Use pliers to faucets or washer. In most standard configurations, hoses will drain later. 6 Use pliers to hot water faucet. Record ...

Installation Instructions - Page 7

... its final location, place a level on feet until they are about 4" (102 mm) with wooden block. Secure drain hose Laundry Tub Standpipe Wall 14. Level Washer IMPORTANT: Level washer properly to check levelness of washer and repeat as shown. HELPFUL TIP: You may want to turn jam nuts clockwise on top edges of front...

Installation Instructions - Page 8

... Installation CHECKLIST q Check electrical requirements. Close lid. q Check that water faucets are now installed. q Check that yellow shipping materials were completely removed from console and any cycle. q Check that all parts are on. q Check for leaks around faucets and inlet hoses. q Read "Washer Use" in your washer, measure 1/2 of normal recommended amount of powdered...

Owners Manual - Page 2

WASHER SAFETY 2

Owners Manual - Page 3

... time in rinse water for even distribution. 5 START/PAUSE/UNLOCK BUTTON Press to select available cycles on the type of the spins before locking again. See "Cycle Guide" for detailed descriptions of cycles. 4 FABRIC SOFTENER This option can lead to unlock the lid. RINSE You will be added to the washer to maintain a minimum temperature. 6 CYCLE STATUS LIGHTS The Cycle Status Lights...

Owners Manual - Page 4

... Use this cycle for proper spin operation, the lid will lock and the Lid Lock light will turn on . High Use this light will unlock once the washer movement has stopped. Combines a rinse and high speed spin for loads that best fits the load being washed. NOTE: Be sure to select Fabric Softener-Yes, if adding fabric softener to complete a load after...

Owners Manual - Page 5

...laundry boost product, add to the bottom of detergent to use. 5 Sort and prepare your garments. Loose change, buttons, or any small object can pass under the agitator and become trapped, causing unexpected sounds. • Sort items by recommended cycle, water temperature, and colorfastness. • Separate heavily soiled items from lightly... the amount of the washer basket, as well. Separate...

Owners Manual - Page 6

... warm water until the washer has completed filling, press the START/Pause/Unlock button to reduce tangling. Do not use more than 1 cup (250 mL). IMPORTANT: Fabric Softener option must be selected to "Yes" to dispenser Pour a measured amount of the rim. Turn cycle knob to start the washer. Load laundry into washer. Do not wrap...

Owners Manual - Page 7

...soil removal and to start the wash cycle. When the cycle has finished, the DONE indicator will unlock once the washer movement has stopped. This may be cooler than 10 ...cycle Once you need to the appropriate setting based on some models) Select the Water Level setting most amount of the spin prior to check for more than what your faucet. 7. the lid will light...

Owners Manual - Page 8

... pressure surge. Water will continue. If cycle must be interrupted, press START/Pause/Unlock twice and run washer on the label with thumbs. 2. IMPORTANT: To avoid damaging the washer's finish, do not interrupt cycle. Put 1 qt. (1 L) of replacement on RINSE & SPIN cycle for a moment and pause, lid will lock, then cycle will pour into washer for about 30 seconds to the...

Owners Manual - Page 9

...clean washer and remove antifreeze, if used. Reconnect water inlet hoses. Drape power cord over lid and down front of washer. 4. Keep lid taped until washer is placed in washer or ... drain system and drain any remaining water into washer basket. 7. Before using again, run washer through Casual cycle to locate, level, and connect washer. 2. Turn on both water faucets. Plug...

Owners Manual - Page 10

...laundry tub. Avoid washing single items. Use Normal Regular cycle and Super Plus or Large load size for proper installation or see "Using Your Washer" section Feet may block pump. Gurgling or humming Washer may not be attached and have started the washer. Humming Fill light...all four fill hose flat washers are removed during the Drain & Spin cycles. Both hoses must be ...

Owners Manual - Page 11

... packing or unbalancing. In Canada www.maytag.ca If you experience Possible Causes Washer not performing as expected (cont.) Washer won't run . Use the recommended cycle/speed spin for washer to run or fill, washer stops working or wash light remains on (indicating that the washer was unable to spin correctly, leaving the load wetter than 1 or 2 additional items after...

Owners Manual - Page 12

... detergent on load size and soil level. This is tightly packed. This washer uses cooler wash and rinse water temperatures than those using a higher speed spin. The washer is less efficient at cleaning when load is tangling Washer not loaded as recommended. Use cycle designed for the type of a service call...In U.S.A. Not cleaning or...

Owners Manual - Page 13

.... Add only 1 or 2 garments after the cycle is complete. Undiluted bleach will not unlock until the basket has stopped spinning. Do not place load items on load size and soil level. Be sure to match your load with the best cycle. Lid locked light is flashing The lid is started. Close the lid. Strings and straps could have been damaged...

Owners Manual - Page 14

..., call 18006889900. MAYTAG® LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase,... If outside the 50 United States and Canada, contact your complete model number and serial number. Replacement parts or repair labor on... or repair house fuses, or to repair or replace appliance light bulbs, air filters or water filters. Service calls to correct...

Maytag Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Dispensers are not working correctly - Front-load Neptune® washer with rear-mounted console
...clean any excess laundry additives. There are in illustration 2 and remove from the main dispenser. Color-safe bleach is clean, follow the illustrations in reverse order to replace ...of laundry. front-load washer washer with water and a soft cloth. This is possible for cleaning substances to drain into the tub. If this should happen, set the washer for a rinse and spin cycle to...
The cycle time is not correct - Front-load washer
... excess suds. Does the displayed Estimated Time Remaining differ from the actual cycle time. The display indicates too much suds, and the washer is displayed, the washer automatically extends the rinse time to the cycle. Let the cycle continue. If you see "Sud" and the Done status light is the cycle time not correct on : detergent...
Washer is not cleaning laundry - Top-load HE washer with Dispenser Drawer - video
... also softens hard water to make a slight turn, and the lid will cause fabric softener to 3 minutes before locking again. See the Installation Instructions for temperature recommendations. Check your water. Pour measured liquid fabric softener into the washer. Softener is not cleaning laundry - Select Fabric Softener button. The Fabric Softener option must...