Maytag MHWZ600TW Support Question
Maytag MHWZ600TW Support Question
Find answers below for this question about Maytag MHWZ600TW - Epic Z Front Load Washer.Need a Maytag MHWZ600TW manual? We have 1 online manual for this item!
Question posted by aliciaasp on August 17th, 2014
My Turn Washer
My Turn Washer
When I press star to start the cycle the washer is turned off, please help !!!!
Current Answers
Answer #1: Posted by Odin on August 18th, 2014 6:30 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
See these alternative solutions. (Ignore the paragraph in red relating to a partial model number.)
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Maytag MHWZ600TW Manual Pages
Use and Care Guide - Page 5
... C. Transport bolt hole plug (4)
E.
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Drain hose form B. To do so, you purchased your washer and dryer? Drain hose G.
A
B
C F
G
D
E
A. Inlet hose washer (4) D. Beaded strap F. Hose clamp
Alternate Parts
Your installation may select a 10" (254 mm) or a 15...
Use and Care Guide - Page 6
...floor to support the washer with a total weight (water and load) of installation and servicing. See "Washer Care" for information on all sides of the washer.
Recommended installation spacing ... custom counter, or in a basement, laundry room, closet, or recessed area. Installation clearances „ The location must be large enough to allow the washer door to reduce noise transfer.
„...
Use and Care Guide - Page 8
... 96" (2.4 m) from the bottom of the washer. C
D
30" min. (762 mm)
A
B
8
Select the drain hose installation method you need. The top of the laundry tub must be no higher than 17 gal. ... The dimensions shown are required.
7" (178 mm) 7" (178 mm)
9" (229 mm)
Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. For cabinet installation, with a door, ...
Use and Care Guide - Page 10
...4 bolts are removed. Firmly seat the washer into each end of the rear panel and close the hole with an additional two-thirds turn.
1.
Washer
Connect the inlet hoses to move it to... water faucets
Make sure washer drum is empty and flat washers have been placed into a laundry tub, drainpipe, or bucket, to get rid of particles in the rear panel of the washer, loosen the 4 transport...
Use and Care Guide - Page 11
... if bulges, kinks, cuts, wear, or leaks are found.
11
CH
2. C. Screw on coupling by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional two-thirds turn. Cold water inlet H. Attach the hot water hose to reduce the risk of hose failure.
Damage to the...
Use and Care Guide - Page 12
... a gap for air.
„ Do not lay excess hose on the top edge of the laundry tub. If the washer is level.
12 Repeat steps 1-3 until washer is against a wall, move the washer out slightly before tipping back. Laundry tub drain or standpipe drain
Connect the drain hose form to adjust back feet.
4.
Hose should...
Use and Care Guide - Page 13
..., fire, or electrical shock.
7.
Failure to complete one whole cycle. Pour the detergent into a grounded 3 prong outlet. Use only HE High Efficiency detergent.
13 The washer should not move front to back, side to turn the locknuts on the feet, tightly against the washer cabinet, the washer may vibrate.
6. See "Electrical Requirements."
2. Check that the...
Use and Care Guide - Page 14
..., and Clean Washer. The Sanitary cycle also helps eliminate 99.9% of the cycle, and the bleach is added after the enzymes have less moisture than for delicate items and is started. aureus, which are evenly balanced. This washer allows a 7-minute period in all laundry products before the washer is powerful enough to drive an average clothes load up to...
Use and Care Guide - Page 15
...washer.
It may be marked "HE" or "High Efficiency." WARNING: To reduce the risk of detergent will likely result in component failures and noticeable mold or mildew. The following is normal during the final installation step, choose the Normal cycle and run it without clothes. Do not store laundry products on the load...washing clothes.
15 Starting Your Washer
Using the Proper...
Use and Care Guide - Page 16
... item. Press again to avoid spills. See "Using the Dispenser." Select START.
Do not put laundry products directly into the wash tub.
It may seep out of suds for approximately 1 second). „ If you are made to remain in the Estimated Time Remaining display. Close drawer slowly to turn it on the washer by pulling...
Use and Care Guide - Page 17
...manufacturer's directions for your load.
„ Always measure liquid chlorine bleach. Fabric softener compartment (Letter D in this compartment. Changing Cycles, Options, and Modifiers
...Cycle, or Extra
Rinse. 5. The bleach will drain automatically before START is complete, the door unlocks. Select desired cycle. 4. Select and hold START (for approximately 1 second).
The washer...
Use and Care Guide - Page 18
... after the ADD A GARMENT period is over, the wash cycle needs to the washer after the cycle has started . To unlock the controls Select and hold START (for different types of clothing is selected. The Estimated Time Remaining can add items to be added. 2. If a large load of fabric and soil levels. Not all Options and...
Use and Care Guide - Page 19
... low spin to ensure proper performance during this cycle to wash loads of bleach. This cycle combines fast-speed tumbling, a shortened wash time, and high speed spin to shorten drying times.
To use Spin Only setting „ Select SPIN Only cycle. „ Press START.
19 Normal
Use this cycle. This cycle combines fast-speed tumbling, longer wash time...
Use and Care Guide - Page 20
... the desired setting illuminates.
„ To change an option after starting a cycle anytime before the selected Modifier begins. Not all options and cycles.
„ See the "Laundry Guide" section for that need improved stain treatment. You can be heated to a hot water temperature to a load using the fabric softener dispenser. Prewash
Use this option for...
Use and Care Guide - Page 21
...load types and their corresponding cycles. The ATC is automatically turned ON when a cycle is selected.
Warm rinses leave the loads...; ATC works for fabrics. CYCLE
SUGGESTED LOAD TYPE
AVAILABLE OPTIONS
Delay Start Prewash MAXEXTRACT™ Stain Cycle
Sanitary
Heavily soiled underwear, towels...and maintains a uniform water temperature.
Laundry Guide
Refer to light soils
COLD
Colors...
Use and Care Guide - Page 22
... lint and dirt. „ Turn wool and synthetic knits inside out to use less detergent based on load size. Sorting „ Separate heavily soiled items from noncolorfast items. „ Sort by fabric and construction (sturdy cottons, knits, delicate items).
It may rust if left in washer errors, longer cycle times, and reduced rinsing performance...
Use and Care Guide - Page 25
... Dispenser").
This helps avoid flooding (due...cycle with ½ the manufacturer's recommended
amount of HE detergent for an extended period of your washer only when you should: „ Unplug washer or disconnect power. „ Turn off the water supply to the washer. Unplug the power cord. 3. IMPORTANT: Call service. Use a soft damp cloth or sponge to wipe up for relocation by pressing...
Use and Care Guide - Page 27
...call an electrician.
„ Is your washer and to the correct compartments. Press and hold START/PAUSE, for 1 second.
„ ...Washer odor
„ Have you using an extension cord? This washer has a tight seal to lock/unlock controls.
27
Do not remove ground prong. Control won't accept selections or won 't start a new cycle.
„ Is the door locked? Check household plumbing (laundry...
Use and Care Guide - Page 28
...water faucets are detected, a special suds routine automatically starts. Turn off the water and remove inlet hoses from the washer. HE detergent is normal. Some cycles feature periods of the drain hose more frequently when...Allow the cycle to extend the drain hose the proper length into the drain pipe more items or redistribute the load.
28 The hose needs an air gap. Press POWER on...
Use and Care Guide - Page 29
...; Did you sort properly? The cycle time will be balanced. This routine will cause wrinkling. If larger loads are detected, a special suds routine automatically starts. If the laundry is designed for clothing stuck between spin basket and outer tub. gray whites, dingy colors
„ Did you add detergent to the washer drum.
„ Did you...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The water temperature is not correct - Top-load washer
If so, turn off the water lines at the nearest sink until you have hot water and then begin a load of laundry. Check that the rubber gaskets are in each of time? The distance from the washer? Do you have an ENERGY STAR ® Top-load washer Cold and Cool water wash differences - Top-load washer The water... -
Lint is on the load - Top-load HE washer with Dispensers in Corners
... higher-speed wash action. Choose cycles with Dispenser Drawer - Top-load HE washer with Dispensers in Corners Lint is on the load in pockets. See also: Why HE High Efficiency detergent is on the load - New clothes or linen items tend to starting a new load of laundry? Was the laundry sorted? Sort lint-producing fabrics... -
The water temperature is not correct - Front-load washer
... hose to see if the hot and cold water inlet hoses were reversed during start-up the available hot water faster than I find them online. Turn the water back on, and make a difference in a short amount of time? Top-load washer Warm or hot wash temperatures are no leaks. Enter Model Number How do...
Similar Questions
Maytag Epic Z Washer Turns Off When Wash Cycle Starts
(Posted by daphi 10 years ago)
My Maytag Epic Z Washer Powers Off When Pressing The Start Button
(Posted by omarastebe 10 years ago)
Maytag Front Load Washer Mhwz600tw02 Will Not Turn On
(Posted by sjp3tajma 10 years ago)
Maytag Epic Z Washer Turns On But Won't Start
(Posted by trl75kerr 10 years ago)
Maytag Epic Z Has Stopped Working. It Powers Up But When I Press The Start Butt
Maytag Epic Z has stopped working. It powers up but when I press the start button it lights up but...
Maytag Epic Z has stopped working. It powers up but when I press the start button it lights up but...
(Posted by kcoxking 11 years ago)