Maytag MHWE450WW Support Question
Maytag MHWE450WW Support Question
Find answers below for this question about Maytag MHWE450WW - 4.5 cu. Ft. Front Load Washer.Need a Maytag MHWE450WW manual? We have 2 online manuals for this item!
Question posted by giants41323 on May 20th, 2016
Washer Stops Recently
keep getting code F21 what does that mean
Current Answers
Answer #1: Posted by Odin on May 20th, 2016 10:44 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Communication error between the main electronic control board and the motor control board
Unplug the washer and check the wire harness connections on the main electronic control board, motor control board and drive motor. Reconnect any loose wires and replace any damaged wire harnesses. If there are no wire connection problems, replace the motor control board. If the problem continues, replace the main electronic control board.
Unplug the washer and check the wire harness connections on the main electronic control board, motor control board and drive motor. Reconnect any loose wires and replace any damaged wire harnesses. If there are no wire connection problems, replace the motor control board. If the problem continues, replace the main electronic control board.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Maytag MHWE450WW Manual Pages
Owners Manual - Page 3
...have provided many important safety messages in this manual and on your appliance. These words mean:
DANGER
You can be killed or seriously injured if you don't immediately follow the... if you don't follow instructions. This symbol alerts you to reduce the chance of others .
WASHER SAFETY
Your safety and the safety of injury, and tell you what can kill or hurt you and others are...
Owners Manual - Page 4
Tools needed for connecting the water inlet hoses
Tools needed for connecting the drain hose „ Locking pliers (that open to 19/16" [39.5 mm])
„ Pliers (that open to 19/16" [39.5 mm])
„ Flashlight (optional)
4 The parts supplied are in the washer drum. INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Owners Manual - Page 5
Drain hose form B. Inlet hose washers (4) D. Beaded strap F. If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead ...may require additional parts. and connector kit, Part Number 285835
4 ft (1.2 m) drain hose extension kit, Part Number 285863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008
Optional pedestal
This pedestal is available ...
Owners Manual - Page 6
.../4" (970 mm)
„ Hot and cold water faucets located within 6 ft (1.8 m) of 400 lbs (180 kg).
Installation clearances „ The location must be large enough to allow the washer door to support the washer with a maximum slope of the washer is your washer in a basement, laundry room, closet, or recessed area. Location Requirements
Selecting the proper...
Owners Manual - Page 7
... - closet or confined area
Recommended installation spacing for recessed or closet installation, with stacked washer and dryer
The dimensions shown are for the recommended spacing.
48 in.2 * (310...installation, with or without a pedestal
The dimensions shown are for the recommended spacing. closet or confined area B. Washer on pedestal
18" min. (457 mm)
1" (25 mm)
27" (686 mm)
A
1" (...
Owners Manual - Page 8
...½" 1" 1" 27"
1"
(102 mm) (800 mm) (25 mm) (25 mm) (686 mm) (25 mm)
Drain System
The washer can result in the top are
required.
7" (178 mm) 7" (178 mm)
Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. A
B
8 See "Tools and Parts." Failure to follow these instructions can...
Owners Manual - Page 9
...also retain the power cord inside the washer until the bolts are removed, discard bolt and spacers. NOTE: If the washer is within approximately 3 ft (900 mm) of its final location... washer is equipped with a power supply cord having a 3 prong grounding plug.
„ To minimize possible shock hazard, the cord must be properly set up for relocation by a qualified electrician.
„ If codes ...
Owners Manual - Page 12
...raise the temperature of the unit and makes the washer self-cleaning, flushing the machine's interior free of all the laundry products before they touch any garments. The water... Shock Hazard Plug into a grounded 3 prong outlet. 8. Read "Washer Use." 9. This washer provides a threecompartment dispenser which means fewer loads. Super Size Capacity Since there is then sprayed from the top front...
Owners Manual - Page 13
... Detergent System ensures that no water or detergent is clean before operating this washer. Starting Your Washer
Using the Proper Detergent
Use only High Efficiency detergents. Using regular detergent will be fully loaded, but not tightly packed. First Wash Cycle Without Laundry
Before washing clothes for the best performance.
Use 1/2 the manufacturer's recommended amount...
Owners Manual - Page 14
...washer as soon as it stops.
8. When selecting a wash cycle, the preset Options, Wash Temp, Spin Speed, and Soil Level for liquid fabric softener.
Turn on load size. Using the Dispenser
Your new washer...it unnecessary for small items.
2. Use only HE High Efficiency detergent. Add the desired laundry product to avoid a spill). Push in a mesh garment bag.
„ When unloading...
Owners Manual - Page 15
... softener dispenser, if desired. Pausing or Restarting
1. To pause the washer at the best time during the Extra Rinse.
„ Do not...Options and Modifiers are using the Delay Wash option, powdered laundry products should be used . Select desired cycle. 3. The...type selector
Chlorine bleach compartment (Letter D in position for load size.
„ If you are available with this ...
Owners Manual - Page 16
...times.
This cycle combines mediumspeed tumbling and high-speed spin.
16 You can be removed from the washer.
The CONTROL LOCK status light illuminates.
„ Each cycle has a preset Soil Level (cycle ...and Spin Speed, and may be selected by turning the Cycle control knob to wash loads of your laundry. Normal/Casual Use this cycle, the heater will cancel the Wash Cycle. The SUDs ...
Owners Manual - Page 17
... the removal of all soil and stains from your laundry. This cycle uses a higher water level in combination with AFFRESH™ Use this cycle once a month to keep the inside of your washer or to get a rinse and spin only. NOTE: For more delicate loads, when using a "Gentle" cycle on clothing, bedding, and towels...
Owners Manual - Page 18
... bleach residue from that option will flash. See "Preset Cycle Settings" in the removal of your laundry.
18
„ To change Soil Level (cycle time), select the SOIL LEVEL button until the ... Fresh Spin (Fresh Hold) option will automatically stop and the door lock will be a short tone, and the light for a cycle. Warm rinses leave the loads drier than 60°F (15.6°C), detergents...
Owners Manual - Page 19
... for best results.
„ Mix large and small items, avoid washing single items, and load evenly.
„ Wash small items, such as 2x or higher will be filled with AFFRESH..., sweatshirts, pants, and outdoor garments. Heavily soiled work clothes, and diapers. LAUNDRY GUIDE
Refer to avoid scratching the washer interior. Listed to the right are made of cotton, linen, polyester, or nylon...
Owners Manual - Page 20
...door open.
The machine will not immediately stop the cycle.
Begin procedure 1.
Unloading „ Remove clothes from the washer.
A
A. d) Wipe down these ... towels
Mixed Load
3 sheets (1 king, 2 twin) 4 pillowcases 3 shirts 3 blouses
Loading
2 sweatpants 2 sweatshirts
14 washcloths
9 T-shirts 9 shorts 10 handkerchiefs
WASHER CARE
Cleaning Your Washer
Cleaning the ...
Owners Manual - Page 22
...load? Unplug washer or disconnect power. Check the following : Is the washer door firmly shut? The door must be completely closed , but may keep the door from the seal area so the clothes can result in the washer. The door may look closed for service. „ "F21... an adapter. Washer must be latched. www.maytag.com/help In Canada www.maytag.ca
Washer displaying code message and tone...
Owners Manual - Page 23
... For best results, add detergent to avoid water leaks. Washer stops
„ Check the following : Is the power cord ...washer level? Dispensers clogged or leaking
„ Are the laundry products in the correct position? Add the correct amounts of the Max ExtractTM option is recommended for heavy loads to the "Installation Instructions" for leaks.
Was the door open to allow the washer...
Owners Manual - Page 24
...
„ Did you choose the Whitest Whites cycle? Use hot or warm washes if safe for smaller load sizes (2-3 items of dye, unload the washer as soon as it stops.
„ Did you unload the washer promptly? Use more detergent for your hot water system is complete, then resume with the remainder of the...
Energy Guide - Page 1
Clothes Washer Capacity: Standard
Maytag Cat. Government
Federal law prohibits removal of $1.218 per kWh and natural gas
cost... utility rates and use.
• Cost range based only on standard capacity models. • Estimated operating cost based on eight wash loads a week and a 2007
national average electricity cost of 10.65 cents per therm.
• For more information, visit www.ftc....
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The water temperature is not correct - Top-load washer
... rinse and warm final sprays. Top-load washers Washer fills slowly - You may use less than I do? Top-load washer The water temperature in my top-load washer is obtained by using lower water temperatures that there are in a short amount of the inlet hose connections. Is the washer new or just recently installed? Check that the rubber... -
Display shows uL - Top-load washer with Dispensers in Corners
... tightened. See the Installation Instructions for details. This error code indicates that an unbalanced load is flashing after the recovery routine has stopped, open lid and redistribute the load. washer display shows uL. -
The water temperature is not correct - Front-load washer
... until you do I expect - Washing many loads in my front-load washer is not correct - Top-load washer Display shows F20 or FH - Front-load washer FAQs Knowledgebase search tips Cold temperature selections - You may use up operation. Front-load washer The water temperature in a short amount of laundry. The distance from the washer? Enter Model Number How do not...
Similar Questions
What Is The Cu. Ft Of A Maytag Mvwx700xwo?
what is the cu. ft of a Maytag Mvwx700xwo?
what is the cu. ft of a Maytag Mvwx700xwo?
(Posted by grimesbill 6 years ago)
Cu Ft For My Maytag Washer,model# Mhwe450ww02 Front Load Washer
Hi, I want to know cu ft for my Maytag washer,Model# mhwe450ww02 front load washer
Hi, I want to know cu ft for my Maytag washer,Model# mhwe450ww02 front load washer
(Posted by rashmi3462 8 years ago)
Maytag Epic Z Washer What Does The Code F-21 Mean
(Posted by karlitch 10 years ago)
Maytag Mhwe450ww02 - 4.5 Cu. Ft. Front Load Washer
Is there any recall info for Maytag Mhwe450ww02 - 4.5 Cu. Ft. Front Load Washer?
Is there any recall info for Maytag Mhwe450ww02 - 4.5 Cu. Ft. Front Load Washer?
(Posted by hhppjj 10 years ago)
Maytag Mhwe450ww02 - 4.5 Cu. Ft. Front Load Washer.
The washer makes extremely loud noise during spinning. Do you know what's going on?
The washer makes extremely loud noise during spinning. Do you know what's going on?
(Posted by hhppjj 10 years ago)