Makita HR5000 Support Question
Makita HR5000 Support Question
Find answers below for this question about Makita HR5000.Need a Makita HR5000 manual? We have 2 online manuals for this item!
Question posted by fcama10 on November 9th, 2012
Chipping,scaling And Demolition Problem
the motor to my rotary hammer is fine....but I can't do the hammering.... what can be done to fix this?
Current Answers
Related Makita HR5000 Manual Pages
Owners Manual - Page 1
Rotary Hammer
50 mm (2") MODEL HR5000
DOUBLE INSULATION
003101
INSTRUCTION MANUAL
WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com
Owners Manual - Page 2
...plug does not fit fully in a polarized outlet only one way. Do not operate power tools in explosive atmospheres, such as in electric shock, fire and/or serious personal injury.
Cluttered...Carbide-tipped bit
Core bit
Concrete Hume pipe
No load speed (RPM)
Blows per minute
Overall length
Net weight
HR5000 50 mm (2") 150 mm (5-7/8") 255 mm (10")
260/min. 2,100
476 mm (18-3/4") 9.6 kg ...
Owners Manual - Page 3
...Dress properly. Contain long hair. Always wear eye protection. Holding the work by poorly maintained tools.
22. Disconnect the plug from heat, oil, sharp edges or moving parts.
11. ... the risk of electric shock if your application. There is grounded.
6. Do not expose power tools to install a polarized outlet. Personal Safety
9. Do not overreach. Dust mask, non-skid safety...
Owners Manual - Page 4
.... Table 1: Minimum gage for extended periods. SERVICE
23. Tool service must be sure to high intensity noise can suffer serious...tools by qualified repair personnel. Wear ear protectors when using an extension cord, be performed only by insulated gripping surfaces when performing an operation where the cutting tool may create a risk of unauthorized parts or failure to rotary hammer...
Owners Manual - Page 5
... any one is difficult.
7. Follow material supplier safety data. Hold the tool firmly with both hands.
9. SAVE THESE INSTRUCTIONS
WARNING: MISUSE or failure to prevent dust inhalation and skin contact. Without proper warm-up, hammering operation is below when using the tool in this instruction manual may be sure you have a firm footing...
Owners Manual - Page 6
... off and unplugged before adjusting or checking function on the tool.
1 1. FUNCTIONAL DESCRIPTION
CAUTION:
• Always be
sure that the change lever is always positively located in one of the two action mode positions. Change lever 2. For hammering only 3.
Hammering only For chipping, scaling or demolition operations, rotate the change lever to the "OFF" position when...
Owners Manual - Page 7
... can cause damage to
2
secure the bit.
180
1. B
7 Screw the side grip on either side of the tool for downward drilling or chipping operations. Tool retainer
37 27
19
19
A
003155
38.5 37 16ø
CAUTION: • Never use A-type shank bits.
To remove the bit, follow the installation procedure ...
Owners Manual - Page 8
... and sudden twisting force exerted on the tool so that the tool will not bounce around, uncontrolled. Hold the tool firmly with chips or particles. OPERATION
003202 Hammer drilling operation
Set the change lever to ...switch trigger. Blow-out bulb
003208 Chipping/Scaling/Demolition
Set the change lever to do so may be resumed. Pressing very hard on the tool will be cleaned out and normal ...
Owners Manual - Page 9
... remove the core bit, follow the procedures 1 or 2.
003214 1. 1. Then resume drilling. Hold the adapter with the core bit in the tool in the core bit and tap with a hammer to the position. Adapter
1
003209
1
Core bit (optional accessory) When using the center bit Screw the core bit on . Then rest the...
Owners Manual - Page 10
... the position. Core bit 2. Rest the core bit on the concrete and turn the tool on the adapter. Install the adapter with the core bit in the tool in the holders. NOTE:
• No problem is switched off the motor. To remove the core bit, follow the same removal procedures covered in the tightening...
Owners Manual - Page 11
... service. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.
1 2
1. Lock nut wrench 2.
Hex wrench 2. Screwdriver 2. Hammer grease
Lubrication
003236 This tool requires no hourly or daily lubrication because it up.
Wipe out the old grease inside the crank housing. However, if circumstances require that...
Owners Manual - Page 12
... • Bull point • Cold chisel • Scaling chisel • Clay spade • Grooving chisel • Rammer • Bushing tool • Spline shank to A-Taper adapter • Spline... shank to SDS adapter • Core bit • Core bit adapter • Hammer grease • Bit grease •...
Owners Manual - Page 14
...
Magazine
From Dealer
Newspaper
Store Display
Catalog
Radio
Exhibition
From Friend
Previous Usage
Other (
)
2. This product was purchased from:
Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply
Other (
3.
MAIL THIS PORTION
Your answers to the following questions are : Design Features Size Price Makita Brand
Repair Service
Durability...
Owners Manual - Page 15
...) to one of the Makita Factory Service Centers listed, or to the outside of the carton detailing the problem with your tool. Be sure to attach a letter to an Authorized Makita Service Center. Denver, CO 80239-2709 (303) 371-2850
FLORIDA 750 East Sample Road Pompano Beach, ...
Owners Manual - Page 16
... do not allow the exclusion or limitation of normal wear and tear:
• the tool has been abused, misused or improperly maintained:
• alterations have other rights which vary...Makita's Factory or Authorized Service Centers. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by others:
• repairs are specially designed to filter out microscopic particles...
Parts Breakdown - Page 2
..., HR5000 H. WASHER 8, HR5000 COMP. GEAR 41, HR5000 STRIKER, HR5000,T1 STRIKER, HR5000, T2
O-RING 32, HR5000, T2 PISTON RING 40, HM1211 O-RING 32, HR5000, T2 PISTON RING 40, HM1211 PIN 10, HM1211 PISTON, HM1211 PISTON, HR5000, T2 CRANK CAP, HR5000 O RING 71, HR5000 CONNECTING ROD, HR5000 N. BEARING 52, HR5000 F. WASHER 43, HR5000 BALL BEARING 6907, HR5000 NUT M34. 8-41,HR5000 X RING 28, HR5000...
Parts Breakdown - Page 3
...Parts Breakdown
58
331132-5
TOOL RETAINER, HR5000
59
322203-9
TOOL HOLDER, HR5000
60
231281-7
COMP. BOLT M5X16, HM1211B
84
922376-4
H.S.H. SCREW M4X16, HR5000
101
651145-3
SWITCH, ...RING 30, HR5000
73
265346-3
HEX BOLT M5X55, HR5000
75
524831-8
FIELD ,HR5000
76
953106-2
RIVET 0-5, HM1500
77
855983-7
NAME PLATE, HR5000
78
159054-5
MOTOR HOUSING, HR5000
79
643650...
Parts Breakdown - Page 4
Parts Breakdown
123
211469-5
BALL BEARING 6907, HR5000
400
150589-9
PLASTIC TOOL CASE,HR3851,HR5000
401
783202-0
HEX WRENCH 4, JR3000V
404
273472-4
GRIP 32, HR3851
500
134797-0
SIDE HANDLE ASSEMBLY, HR5000,T2
500
134887-9
SIDE HANDLE ASS'Y, HR5000
900
810246-8
N/A
HR5000
1 1 1 1 1 1 1
Page 4 of 4
8/18/2010
Similar Questions
Broken Bits
I purchased my Makita HR2811F around 6 month ago and it broke 6 chisel bits in the choke area. What ...
I purchased my Makita HR2811F around 6 month ago and it broke 6 chisel bits in the choke area. What ...
(Posted by teinpr 2 years ago)
Makita Hr5001c Motor Problem
The motor runs at correct rev's but drops a slight bit of rev's every revolution but then picks up.C...
The motor runs at correct rev's but drops a slight bit of rev's every revolution but then picks up.C...
(Posted by tim50103 7 years ago)
Makita Hr2470 Electrical Problem
good daycan you please assist. My hr 2470 only works in reverse. Please tell me what part to replace...
good daycan you please assist. My hr 2470 only works in reverse. Please tell me what part to replace...
(Posted by dantho98260 9 years ago)
Repa[r Of A Hr5000 Drill
what parts are faulty when my drill does not hammer
what parts are faulty when my drill does not hammer
(Posted by Anonymous-139111 9 years ago)