Makita HR4041C Support Question

Find answers below for this question about Makita HR4041C.
Need a Makita HR4041C manual? We have 3 online manuals for this item!

Makita Overview Questions Manuals Reviews Videos Research

Question posted by joe56647 on March 10th, 2013

How Do I Change The Brushes? Owners Manual Does Not Say

The person who posted this question about this Makita product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by tintinb on March 15th, 2013 6:02 PM

This answer was accepted by the poster of the original question.

tintinb

Member since:
October 26th, 2012

Points: 7,056,560

1,100
points

The complete procedure in changing the brushes and other instructions for your Makita HR4041C can be read / downloaded here at HelpOwl.com. Here's the link to the download page:

http://www.helpowl.com/manuals/Makita/HR4041C/179008

If you have more questions, please don't hesitate to ask here at HelpOwl. Experts here are always willing to answer your questions to the best of our knowledge and expertise.

Regards,

Tintin

Related Makita HR4041C Manual Pages

Owners Manual - Page 2

...will increase the risk of the power tool may result in moving parts. Use of these are subject to change without notice. • Note: ...tool. When operating a power tool outdoors, use . A wrench or a key left attached to country. Power tool use common sense when operating a power tool. Personal Safety 9. Avoid accidental starting. ENGLISH SPECIFICATIONS Model HR4041C...

Owners Manual - Page 3

.... Check for lubricating and changing accessories. 25. Keep handles dry, clean and free from the power tool before operation. 6. Check tightness of moving parts. 11. Be sure no load. they may contact hidden wiring or its own cord. Do not use this instruction manual may affect the power tools operation. This will loosen up...

Owners Manual - Page 4

...Always be turned only as far as 5 and back to see that the tool is switched off and unplugged before carrying out any position. Bit grease (optional accessory) Coat the...desired position and then tighten it by turning the adjusting dial. Speed change 1. Side grip (auxiliary handle) 1. To start the tool, simply pull the switch trigger. The dial is operated continuously at low...

Owners Manual - Page 5

... release it from slipping away from the hole. Depth gauge 2. Light pressure gives best results. Keep the tool in position and prevent it to secure the bit. 1. By repeating this several times, the hole will ... idle, then remove the bit partially from the hole. Clamp screw 007799 007797 Set the change lever to clean the dust out of uniform depth. CAUTION: • There is convenient for ...

Owners Manual - Page 6

... core bit on . Adapter 2 003209 007800 To remove the core bit, follow the procedures 1 or 2. 1. Adapter 2 003216 6 Chipping/Scaling/Demolition 007798 Set the change lever to the position. Then rest the core bit on the concrete and turn the tool on the adapter. Install the adapter with the core bit in the...

Owners Manual - Page 7

... attachments are recommended for this manual. This will allow the old grease to the position and resume drilling. Lubrication This tool requires no hourly or daily ...tool on . To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be relubricated after every 6 months of grease. Rotate the change...

Owners Manual - Page 8

...: repairs have other rights which vary from the date of incidental or consequential damages, so the above limitation may also have been made to the tool. EN0006-1 8 THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY...

Parts Breakdown - Page 2

... 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1 1 4 4 8/18/2010 SPRING 15, HR3851 H.S.H.BOLT M6X25, HM1211B TOOL HOLDER, HR4041C O RING 48, HR2511 X-RING 28, HR5000 NYLON WASHER 29, HR4041C FLAT WASHER 29, HR4041C IMPACT BOLT, HR4041C WASHER 17, HR4041C RUBBER RING 18, HR4041C SLIDE PLATE, HR4041C BARREL CPL.,HR4041C H.S.H. BOLT M4X14, 9005B F. WASHER 12, 5014NB FAN 70, JR3050T ARMATURE ASS'Y 115V...

Parts Breakdown - Page 3

...-6 158257-8 321248-4 805220-9 Parts Breakdown BRUSH HOLDER UNIT,HR4041C CARBON BRUSH CB-350,HR4001C CARBON BRUSH SET CB-350, HR4001C TAPPING SCREW 4X18, 4323K REAR COVER, HR4041C TAPPING SCREW 4X18, 4323K GRIP SPRING 66, HR4041C SQUARE BOLT M8X80, HM0860C SQ. BOLT M6X20, LS1013 SWITCH LEVER, HR4041C SWITCH, HM1303B LEAD UNIT, HR4041C HANDLE CPL., HR4041C TAPPING SCREW, FLANGE 5X25, 5177B...

Flyer (English) - Page 1

... Fast Provides the end-user with Hammering"; 1,300-2,600 BPM No Hammering while Idling Helps Increase Tool Life Torque Limiting Clutch Disengages if Bit Jams DURABILITY High quality Aluminum housing for durability and longer tool life VERSATILITY HR4041C accepts spline shank bits for rotary hammering and 3/4" Hex 21/32" Round for "Hammering Only...

Flyer (English) - Page 2

... HR4041C OPTIONAL ACCESSORIES ■ Spline Shank Carbide-Tipped Rotary Bits Diam. Model HR4041C ...tool life ■ Torque limiting clutch disengages if bit jams ■ Auto cut out carbon brush system automatically shuts down the motor indicating time for "hammering only" or "rotation with hammering"; 1300 -2600 BPM ■ Electronic variable speed control dial enables user to change...