Kenwood KAC-X1R Support Question
Kenwood KAC-X1R Support Question
Find answers below for this question about Kenwood KAC-X1R - eXcelon Amplifier.Need a Kenwood KAC-X1R manual? We have 1 online manual for this item!
Question posted by Akcas98 on January 25th, 2016
Consistent Eo2 Code?
I am getting a consistent EO2 error code. Is there a solution or does this mean the amp is bad and needs replaced?
Current Answers
Answer #1: Posted by TechSupport101 on January 25th, 2016 8:20 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,285
Member since:
May 24th, 2013 Points: 12,171,285
Hi. See the answer here http://www.fixya.com/support/t8432917-amp_flashing_e_02
Related Kenwood KAC-X1R Manual Pages
Instruction Manual - Page 1
... the best performance from your new power amplifier. Familiarity with installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the space provided below. Refer to read through this instruction manual.
Model KAC-X1R/ KAC-PS1D Serial number
US Residence Only
Register...
Instruction Manual - Page 2
... the speakers and then connect suitable speakers to the amplifier.
4Ω
4Ω 8 Ω
4Ω... function installed in Watts) of the car chassis that to which can cause blown...gets dirty, turn off .
If the "E-02" code does not disappear, contact your Kenwood dealer. When a system error...you of water splashing. • When replacing a fuse, only use automotive- Safety precautions...
Instruction Manual - Page 3
...surface temperature of the amplifier will not come into contact with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In ... circuits. 2.Set the unit according to heat will become hot during use. Optional accessory for KAC-X1R.)
Mounting bracket Remote controller
Accessories Part name
Remote cable (6.0 m : 19.7 ft)
Remote...
Instruction Manual - Page 4
...check that no unconnected wires or connectors are touching the car body. Sharing the negative wire of the speaker or ... screw using the supplied hexagon wrench.
Optional accessory for KAC-X1R.)
2CAUTION
• Before connecting the remote controller cables...; If the fuse blows, check wires for shorts, then replace the fuse with the following thicknesses:
Battery wire and ground ...
Instruction Manual - Page 5
... connected. 2.Set the LPF frequency and Bass boost level. 3.Turn the "LINE OUT FILTER" switch "ON". Optional accessory for KAC-X1R.)
You can control the Bass boost level of the remote controller).
■ Multi Amplifier with Remote cable connection (Accessory of
the center unit to "0.2 V (max.)". CENTER UNIT (CD receiver, etc.)
Power control...
Instruction Manual - Page 6
...the low frequency range should be output.
! This improves the reproduction performance of the amplifier. FREQUENCY control Sets the rejection frequency when the "BRF" switch is set to "ON...with the "ISF FREQUENCY" control are rejected and eliminated. The band rejection allows to its controls for KAC-X1R.)
25 25 25
SPEAKER OUTPUT
FUSE (25As3)
POWER IN
p
q rs
t
LINE OUT FILTER
...
Instruction Manual - Page 8
Troubleshooting Guide
What might appear to be a malfunction in the car body.
• The switches may just be set improperly. • The Remote Cable is disconnected. SOLUTION • Connect the input (or output) cables. • Check connections by referring to . • Replace the fuse and use lower volume. • After check the speaker cord...
Similar Questions
Amplifier Sound Cutting
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
(Posted by marksuzyo07 7 years ago)
Wher Is It
what does the remopte wire outlet say aBOVE IT ON THE AMPLIFIER LIKW WHAT PORT DO YOU PUT THE REMOTE...
what does the remopte wire outlet say aBOVE IT ON THE AMPLIFIER LIKW WHAT PORT DO YOU PUT THE REMOTE...
(Posted by HOCKBEAST123 13 years ago)