Kenwood KAC-6104D Support Question
Kenwood KAC-6104D Support Question
Find answers below for this question about Kenwood KAC-6104D - 600 Watt Max Power Class D Mono Amplifier.Need a Kenwood KAC-6104D manual? We have 1 online manual for this item!
Question posted by Larrybatx2020 on December 4th, 2020
How Do I Know Where To Set My Controls At?
The person who posted this question about this Kenwood product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by INIMITABLE on December 4th, 2020 7:44 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,088,520
Member since:
April 3rd, 2020 Points: 2,088,520
instruction here; https://www.manualslib.com/manual/86555/Kenwood-Kac-6104d.html?page=8
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Kenwood KAC-6104D Manual Pages
Owner's Manual (pdf) - Page 1
... Serial number US Residence Only
Register Online
Register your new power amplifier. KAC-6104D
CLASS D MONO POWER AMPLIFIER 3 page 2-9
INSTRUCTION MANUAL
AMPLIFICATEUR MONO CLASSE D 3 page 10-17
MODE D'EMPLOI
AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO 3 página 18-25
MANUAL DE INSTRUCCIONES
Take the time to the model ...
Owner's Manual (pdf) - Page 2
...not install the unit in Watts) of the amplifier. CAUTION
Do not wipe the panel with a 5 mm2 (AWG 10) or more than the output power (in a spot exposed...
English
• Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery's negative ·...set of speakers are going to be greater than one with the prescribed rating.
Owner's Manual (pdf) - Page 3
... and found to Part 15 of the FCC Rules. Contact your local authority for EU countries that interference will help . NOTE
This Class B digital apparatus complies with the limits for a Class B digital device, pursuant to comply with Canadian ICES-003. These limits are expressly approved in the instruction manual. This equipment may...
Owner's Manual (pdf) - Page 5
... short circuits. 2.Set the unit according to the intended usage. 3.Connect the input and output wires of the units. 4.Connect the speaker wires. 5.Connect the power wire, power control wire and grounding... unit malfunctions and a DC signal is sent
to heat will become hot during use. Install the amplifier in a place where people, resins, and other damage. • Do not install near the dashboard...
Owner's Manual (pdf) - Page 6
...level input connections • The genuine-accessory car stereo shall have a maximum power output of no unconnected wires or connectors are touching the car body. Connection
WARNING Remove the ignition key and... to fail.
CAUTION • If sound is not output normally, immediately turn power off before changing the setting of any switch. • If the fuse blows, check wires for this ...
Owner's Manual (pdf) - Page 7
... IN
L
R
SPEAKER LEVEL INPUT
RCA cable* Power control wire*
LPF FREQUENCY[Hz]
150 100
70
50
200
INPUT SENSITIVITY[V]
2 1 0.5
3
0.3
4
[MIN] 5
0.2 [MAX]
OFF ON BASS EXPANDER
LINE IN
L
R
SPEAKER LEVEL INPUT
Genuine-accessory car stereo (No line output center unit etc.)
■ Power wire and Speaker wire connection
Power control wire* (RCA cable connection)
Speaker level input...
Owner's Manual (pdf) - Page 8
... genuine-accessory car stereo. Check whether there is output.
4 INPUT SENSITIVITY control Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of trouble. Use the diagram on , the Power indicator lights. Controls
LPF FREQUENCY[Hz]
150 100
70
50
200
INPUT SENSITIVITY[V]
2 1 0.5
3
0.3
4
[MIN] 5
0.2 [MAX]
OFF...
Owner's Manual (pdf) - Page 9
...2006 RMS Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms)
Audio Section
Max Power Output
Rated Power Output ...in the car body. ...control is not set improperly. Set switches properly by a screw in your unit may be set to the correct position. Adjust the control correctly referring to change without notice.
200 W × 1 75 dBA
600...
Similar Questions
Amplifier Sound Cutting
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
(Posted by marksuzyo07 7 years ago)
Where Do I Connect The Blue Power Control Wire?
I'm installing the unit for bluetooth only (no head unit). where do attach the blue power control wi...
I'm installing the unit for bluetooth only (no head unit). where do attach the blue power control wi...
(Posted by windslammer 8 years ago)
No Power To Kac-6104d Amp
The amp was working fine, but now the power light is off on the amp and the Kenwood head unit is off...
The amp was working fine, but now the power light is off on the amp and the Kenwood head unit is off...
(Posted by jwilliams644508 10 years ago)
Ken Kac6401d 600 Watt Mono Amp
My kenwood 6401d is not working at all!!! When you turn on your ignition the amp turns on, but immed...
My kenwood 6401d is not working at all!!! When you turn on your ignition the amp turns on, but immed...
(Posted by csmoran17 11 years ago)
How To Get The Max Wattage?
alright so I have this amp an 2 12" MTX Terminator single voice coil subs, they are 600w each 1200w ...
alright so I have this amp an 2 12" MTX Terminator single voice coil subs, they are 600w each 1200w ...
(Posted by brandonpetty66 11 years ago)