Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by Anonymous-31900 on June 23rd, 2011
110.47511700 Service Manual
The person who posted this question about this Kenmore product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 1
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS L-78
FRONT-LOADING AUTOMATIC WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR
JOB AID Part No. 8178558
User Guide - Page 2
.... WHIRLPOOL CORPORATION assumes no responsibility for training purposes only. Always use the Wiring Diagram supplied with information on the installation, operation, and service of the Duet Sport™ Front-Loading Automatic Washer. ii - Copyright © 2006, Whirlpool Corporation, Benton Harbor, MI 49022
-
For specific information on our products by anyone other than Authorized...
User Guide - Page 4
Removal Or Replacement 6-8 Washer Care 6-9
Troubleshooting Guide 6-11 WIRING DIAGRAMS 7-1
Washer 7-1 Grounding System 7-2
- Page DIAGNOSTICS & TROUBLESHOOTING 6-1
Diagnostics 6-1 Diagnostic Guide 6-1 Failure/Error Display Codes 6-2 Diagnostic Test 6-5 Error History Display 6-6 History Overview Test Program 6-6 Manual Diagnostic Test 6-7 Manual Overview Test Program 6-7 Electronic ...
User Guide - Page 8
SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6
ATC - 2
ATC - 4
ATC - 4
No
Yes
Yes
Suds Sensor, NTC (Thermistor), Water Level ...
User Guide - Page 9
... block • Ruler or measuring tape
Parts supplied
If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead sewer
Floor drain...ft (1.8 m) Part Number 76314 10 ft (3.0 m) Part Number 350008
A
B
C
D
OPTIONS
Pedestal
You have the option of purchasing pedestals of the items listed here, call the toll-free number on the cover or in the "Assistance or Service" section in the washer...
User Guide - Page 10
...; A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a total weight (water and load) of installation and servicing. Some water can remain in the washer and can be considered.
LOCATION REQUIREMENTS
Selecting the proper location...
User Guide - Page 14
...suspension system during transportation. To avoid suspension and structural damage, your local service center.
CONNECT THE INLET HOSES
Insert new flat washers (supplied) into each of the hole and completely pull out the ....
Then pull the power cord through the opening of the washer that the rear of the unit is within approximately 3 ft (90 cm) of the inlet hoses.
Once all 4 bolts...
User Guide - Page 21
... with gasoline or other flammable fluids. No washer can result in the washer that has ever had any type of oil on the top surface of this manual for more detailed information. Doing so can completely remove oil. Do not store laundry products on it (including cooking oils). Please refer to speci...
User Guide - Page 23
... proper time during Delay, before the wash cycle begins. Liquid chlorine bleach compartment D. Laundry additives are made to add them.
Choosing the Right Detergent
Use only High Effi... COMPLETE light goes off. The washer powers down the washer manually after the cycle is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be marked "HE" or...
User Guide - Page 24
... when you can be automatically dispensed in the final rinse or in this dispenser to your load.
• Always measure liquid chlorine bleach. Do not use .
• Do not fi... not available, the machine will be changed anytime before the door unlocks. To drain the washer manually
1. • Liquid detergent: Measure the amount of liquid detergent with the measurement device which...
User Guide - Page 32
... Normal/Ca- Plug in the upright position. To transport the washer:
1. Unplug the power cord.
3. IMPORTANT: Call service. Do not use an adapter. Follow the "Installation Instructions" to clean the washer and remove the antifreeze, if used. Use 1/2 the manufacturer's recommended amount for a medium sized load. Use 1/2 the manufacturer's recommended amount for a medium sized...
User Guide - Page 39
..., Touchpad/LED Assembly, & Door Switch Assembly
Rear Interlock Switch ECO Valve Motor Control Unit
Drain Pump
4-1 COMPONENT ACCESS
This section instructs you on how to service each component inside the Duet Sport™ Front-Loading Automatic Washer.
The components and their locations are shown below.
User Guide - Page 40
... do so can result in the cover, then lift the cover off the water supply to the washer. 3. Remove the three T-20 hex-head Torx
screws from the two central control unit clips....release tab, and remove the drawer from the central control unit. Replace all parts and panels before servicing.
Dispenser Drawer Release Tab
Top Cover Screws
4-2 To remove the console:
a) Pull out and disconnect ...
User Guide - Page 42
...Central Control Unit Connectors (12)
Electrical Shock Hazard Disconnect power before operating. Unplug washer or disconnect power. 2. When you pull an edge connector off the locking tabs... off the board, first pry the locking tab away from the washer
(see the top right photo).
Replace all parts and panels before servicing. Wire Clamps
6. Failure to release it will go, and remove...
User Guide - Page 44
.... 4. NOTE: The cold water wire connector has a black stripe on it into the washer off the rear panel. Water Inlet Valve
Pull Connector Out
Cold Water (Stripe)
Solenoid Terminal...
1. Replace all parts and panels before servicing.
Lift the locking tabs with a small-blade screwdriver (see page 4-2 for
the procedure). Unplug washer or disconnect power. 2. Turn off the water inlet ...
User Guide - Page 45
.... Replace all parts and panels before servicing. Wire Connector Pressure Switch
1. Unplug washer or disconnect power. 2. Remove the top cover from the washer.
Turn off the water supply to do...REMOVING THE PRESSURE SWITCH
4. Pull the pressure hose off the pressure switch.
5. Failure to the washer. 3. Turn the pressure switch 90° in a clockwise (CW) direction, and align the ...
User Guide - Page 46
...Shock Hazard
Disconnect power before operating. Replace all parts and panels before servicing.
Failure to the washer. 3. Turn off the water supply to do so can result in... wire. To remove the line filter:
a) Remove the T-20 Torx/hex-head screw from the filter. Unplug washer or disconnect power. 2. Ground Screw
Screw
4 Tabs
White Wire Black Wire
Line Filter
4-8 REMOVING THE LINE FILTER...
User Guide - Page 63
... two wires from the switch terminals and unhook the wires from the washer (see step 10 on the next page. Replace all parts and panels before servicing. REMOVING AN INTERLOCK SWITCH
4. If you are servicing the rear interlock switch, pull the washer away from the wall, and remove the rear panel from the clips...
User Guide - Page 81
...and cold water faucets and unplug the unit before servicing. Check wire harness connections to the pump and ...If the door unlock has failed 6 times. Unplug washer or disconnect power. 3. See Manually Unlocking The Door Lock System. Possible Causes/Procedure 1.... 3. Check/clean drain pump filter of the CLEANING WASHER cycle a load is completely closed for any
cycle. Possible Causes/Procedure...
User Guide - Page 83
...error states that have been recorded by the appliance.
• Run through an automated test.
• Run loads to start the test.
1. All of error codes.
This executes the automatic test but does not show ..., all the lights on for 5 seconds.
• Next the washer begins the Diagnostic Test.
• To cancel out of service mode press PAUSE/CANCEL. (This exits you out of the test procedure...
Similar Questions
Kenmore He2 Model 110.47561600 F20 Error Code.
6 minutes into any cycle the washer stops filling and shows the F20 error code. After researching th...
6 minutes into any cycle the washer stops filling and shows the F20 error code. After researching th...
(Posted by riskoj 6 years ago)
Kenmore Elite Front Load Washer Manual Who Used 4.7
(Posted by Loversemc 10 years ago)
Kenmore Model 110.47511700 Excessive Shaking
Excessive shaking during spin mode causing all the display lights to blink? Washer will walk forward...
Excessive shaking during spin mode causing all the display lights to blink? Washer will walk forward...
(Posted by ryobiboss 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)