Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by lorij9696 on July 6th, 2014
He4t Will Not Fill With Water And I Already Replaced The Water Inlet Valve
Kenmore elite he4t washer
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 3
... Requirements 2-1 Installation Instructions 2-6
PRODUCT OPERATION 3-1 Features And Benefits 3-1 Washer Use 3-3 Washer Care 3-12 Troubleshooting 3-15
COMPONENT ACCESS 4-1 Component Locations 4-1 Removing The Console And The Touchpad/LED Assembly 4-2 Removing The Central Control Unit 4-4 Removing The Water Inlet Valve 4-6 Removing The Pressure Switch 4-7 Removing The Line Filter & Power...
User Guide - Page 8
... lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
17.64 lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
1-4 SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min -
User Guide - Page 9
...) 46" (116.8 cm) White WHP1000SQ
15.5" (39.4 cm) 51.5" (130.8 cm) White WHP1500SQ
2-1 Tools needed for this washer. Remember that open to 1-9/16˝ [39.5 mm]) • Flashlight (optional)
Tools needed for connecting the water inlet hoses • Pliers (that the pedestal will add to Buy
Sump pump system (if not already available...
User Guide - Page 10
...washer.
You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water...Kit
Are you planning to support the washer with a total weight (water and load) of 400 lbs (180 kg). Ask for the recommended spacing. Washer Dimensions
50¹⁄4 " (...
User Guide - Page 15
... is connected to the hot water faucet and that might clog the inlet valve screens.
2. Turn on the washer.
2.
Using pliers, tighten the couplings with an additional two-thirds turn. Remove drain hose from the washer
Gently pull the corrugated drain hose from damage due to the washer's cold (C) water faucet. Hot water inlet C. NOTE: Replace inlet hoses after 5 years of...
User Guide - Page 31
... machine freshness, please evaluate your washer.
When replacing your washer during freezing weather, winterize it looking new. Disconnect water inlet hoses from the softener and bleach compartments).
3. Reconnect water inlet hoses to provide ventilation. See "Using the Dispenser." Wash the parts under running water.
Periodically inspect and replace inlet hoses if bulges, kinks...
User Guide - Page 32
...in death, fire, or electrical shock.
4. If washer will be moved during freezing weather, put in 1 qt (1 L) of the washer.
6. To avoid suspension and structural damage, your machine ...the water inlet hoses from the drain system and attach to the rear panel of R.V.-type antifreeze in the upright position. Use 1/2 the manufacturer's recommended amount for a medium sized load. ...
User Guide - Page 33
... Remaining display (on some models).
• "Spin" and "Wash" (HT "Rinse" and "Cycle Complete") illuminated or "F20" on display (Water Inlet Problem-no water or insufficient water supply) Select PAUSE/CANCEL twice to washer clogged? As with the floor. These new sounds and pauses are part of 3/4˝ (19.1 mm) plywood underneath...
User Guide - Page 35
... complete once extra suds are detected, a special suds routine automatically starts. This is used.
• Is the load balanced? Do not remove ground prong. Straighten the hoses.
• Are the water inlet valve screens clogged? The washer pauses for 1 second? The top of the drain hose must be loose yet fit securely. Cycle will occur...
User Guide - Page 36
...
• Did you add detergent to the washer drum.
• Did you overload the washer? The washer can reduce spin speed. See "Connect the Inlet Hoses."
• Are you should use HE...are detected, a special suds routine automatically starts. Wash water colder than 60°F (15.6°C)? Make sure your wet laundry in a load. CYCLE TIME CHANGES/CYCLE TOO LONG
• Estimated...
User Guide - Page 39
COMPONENT ACCESS
This section instructs you on how to service each component inside the Duet Sport™ Front-Loading Automatic Washer. The components and their locations are shown below.
COMPONENT LOCATIONS
Water Inlet Valve
Line Filter
Detergent Dispenser Motor & Assembly
Pressure Switch
Central Control Unit
Temperature Sensor (On Rear Of Tub) Heater (On Rear Of Tub...
User Guide - Page 43
... - Door Lock 3 BK Wires GN Stripe
Board Edge Connectors
HE2 - REASSEMBLY NOTE: The photo shows the connector callouts for the central control unit. Heater
MS2 -
Water Inlet 4 BU Wires RD Stripe
DP2 - Line Filter GN Stripe
DLS2 - Pressure Switch
Not Used
6 BU Wires
TH2 -
User Guide - Page 44
...cold water inlet valve. 4. Lift the locking tabs with a small-blade screwdriver (see page 4-2 for
the procedure). Failure to the washer. 3.
Loosen the clamp, and pull the water inlet hose off the water supply to do so can result in death or electrical shock.
1. REMOVING THE WATER INLET VALVE
Lift Locking Tab
Electrical Shock Hazard Disconnect power before operating. Replace all...
User Guide - Page 71
...Control Unit (CCU). Disconnect the inlet valve solenoid connector VCH7 (see page 4-5) from
the inlet valve terminals. 3. Unplug washer or disconnect power. 2. Unplug washer or disconnect power.
2. Touch....
• Unless stated otherwise, make all connections before replacing components, looking for accessing the inlet valve.
Disconnect the solenoid connectors from the CCU.
3. COMPONENT...
User Guide - Page 80
... and connection to 103°C]) during the first 40 minutes is water in washer or reconnect power. 4. Check resistance of heating element, if present on this
model. (abnormal = infinity) 4. Refer to inlet valves, pressure switch, drain pump and Central Control Unit (CCU).
5.
Verify inlet valve operation. If there is less than 86°F (30°C). Verify...
User Guide - Page 81
...water inlet value, and Central Control Unit (CCU).
4. Check the drive motor for proper shut off hot and cold water...inlet valve for powered rotations. Unplug washer or disconnect power.
2. Check the MCU by weight.
Unplug washer or disconnect power. 3. Possible Causes/Procedure 1. Unplug washer...F31 code will reset the MCU. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the MCU is...
User Guide - Page 84
... reversing movement at wash speed (30 sec).
Fill by cold water inlet valve (4 liters).
Fill by hot water inlet valve to MW position. After 5 seconds all lights should turn off and the most recent error code is to be Checked
Door lock system
Clean Washer Delicate
Clean Washer
Distribution system is displayed.
• All of 5 seconds the lights...
User Guide - Page 85
... before replacing the system...washer must be empty and the control must be Checked
Door lock system
Dispenser Motor Dispenser contact Cold and Hot Water Inlet Valve Overfill level Dispenser Motor Dispenser contact Cold and Hot Water Inlet Valve Overfill Level Dispenser Motor Dispenser contact Cold and Hot Water Inlet Valve Overfill Level Dispenser Motor Dispenser contact Cold Water Inlet Valve...
User Guide - Page 89
...for power going to confirm the touchpad/LED is responding.
4. If no click, replace CCU.
3. Check harness connections to be opened between consecutive wash cycles.
2. The ...plugged in washer or reconnect power.
7.
Check water connections to the unit and within the unit. Check harness connections. 7. Check inlet valves. 3. Plug in washer or reconnect power. 6. Unplug washer or ...
User Guide - Page 90
...sequence shown for an abnormal condition. Unplug washer or disconnect power. 2. Check wire harness connections. 3. Check drain pump. 4. Check that the inlet hoses are clear
of foreign objects. 6. Plug in washer or reconnect power.
6. Remove shipping system. 2. INCORRECT WATER TEMPERATURE
1. Unplug washer or disconnect power.
3. Check the water heater and wire harness connections to it...
Similar Questions
Follow Up To The Kenmore He2t Washer F20 Error Code.
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the...
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the...
(Posted by riskoj 6 years ago)
Kenmore He2 Model 110.47561600 F20 Error Code.
6 minutes into any cycle the washer stops filling and shows the F20 error code. After researching th...
6 minutes into any cycle the washer stops filling and shows the F20 error code. After researching th...
(Posted by riskoj 6 years ago)
Water Pouring Out Of Detergent Dispensed
how do i fix the water coming out of the detergent dispensed?
how do i fix the water coming out of the detergent dispensed?
(Posted by krisc63 10 years ago)
I Replaced The Door Latch Lock On My Front Load Washer The Washer Won't Come On
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the wash...
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the wash...
(Posted by reginaharvey 11 years ago)
Dgree Of Difficulty To Take Out And Replace Front Boot On Front Loading Washer
(Posted by leonard483 12 years ago)