2008 Jeep Liberty Support Question
2008 Jeep Liberty Support Question
Find answers below for this question about 2008 Jeep Liberty.Need a 2008 Jeep Liberty manual? We have 1 online manual for this item!
Question posted by mavkm on August 2nd, 2013
How To Remove Jeep Liberty Headliner
The person who posted this question about this Jeep automobile did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Manual Pages
Owner's Manual - Page 7
... Identification Number
NOTE: It is visible from outside of the instrument panel. It also contains CAUTIONS against operating procedures, which could result in damage to remove the VIN. Observe all Warnings and Cautions. The VIN is illegal to your vehicle. This number also appears on the Automobile Information Disclosure Label affixed...
Owner's Manual - Page 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
A Word About Your Keys ...12 ▫ Ignition Key Removal ...12 ▫ Key-In-Ignition Reminder ...14 Sentry Key ...14 ▫ Replacement Keys ...16 ▫ Customer Key Programming ...16 ▫ General Information ...17 Steering Wheel ...
Owner's Manual - Page 12
These numbers can insert the double-sided keys into the locks with either side up. Ignition Key Removal Automatic Transmission Place the selector lever in a safe place. Then remove the key. Ask your dealer for your vehicle locks.
Vehicle Key 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
A WORD ABOUT YOUR KEYS You...
Owner's Manual - Page 13
... "Delay Power Off to Accessories Until Exit," under "Personal Settings (Customer Programmable Features)," under "Electronic Vehicle Information Center (EVIC)" in Section 4 of this feature. Then remove the key. Opening either front door will cancel this manual.
2
Ignition Key Positions
Manual Transmission - If Equipped Turn the key to the ACC position and...
Owner's Manual - Page 14
Never leave children alone in the ignition, a chime will sound to remove the key. A child could be armed or activated. Key-In-Ignition ...in a vehicle. SENTRY KEY The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended.
NOTE: The Key-In-Ignition...
Owner's Manual - Page 16
...all doors when leaving the vehicle unattended. Turn the ignition switch to the "LOCK" position and remove the first key. 3. Insert the second valid key into the ignition switch. After ten seconds, ... performing the following procedure: 1.
Insert the first valid key into the ignition switch. Always remove Sentry Keys from the vehicle and lock all vehicle keys with a four-digit PIN number....
Owner's Manual - Page 17
... key from the systems memory. The remaining keys must accept any interference that may be reprogrammed. Turn the ignition switch to the "LOCK" position and remove the second key. 4.
Owner's Manual - Page 18
... engage the lock, you will need to know which mode has been activated in the horn. In case one should go off the engine, and remove the key. To Manually Lock the Steering Wheel With the engine running, rotate the steering wheel 1/2 revolution from straight ahead position, turn the wheel slightly...
Owner's Manual - Page 19
... off all doors.
If the system arms successfully, the Vehicle Security Alarm Indicator Light will flash at a slower rate to indicate the alarm is arming. Remove the key from the ignition switch and exit the vehicle. 2. The Vehicle Security Alarm Indicator Light in the instrument cluster will flash rapidly for about...
Owner's Manual - Page 25
... section. NOTE: • Perchlorate Material - special handling may need to be close to the vehicle when using the transmitter to turn off by the system. Remove the screw from the transmitter case (if equipped).
2
Owner's Manual - Page 26
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2. Remove and replace the batteries. Reinstall and tighten the screw until snug (if equipped). This device must accept any interference that may be received including... buttons facing down, use a flat blade tool to pry the two halves of Industry Canada. Operation is subject to damage the seal during removal.
3. Separating Case Halves
2.
Owner's Manual - Page 28
... "P" (Park). • Doors closed. • Hood closed. • Liftgate closed. • Hazard switch off. • Brake switch inactive (brake pedal not pressed). • Ignition key removed from ignition switch. • Battery at an acceptable charge level. • RKE Panic button not pressed.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
How...
Owner's Manual - Page 30
.... WARNING!
• For personal security and safety in a vehicle unattended is down when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If the door lock plunger is dangerous...
Owner's Manual - Page 31
... the power door lock switch or remote keyless entry transmitter.
A chime will lock automatically on each front door trim panel. Use this switch to remove the key. Removing the key or closing the door will not operate. The vehicle speed is above 15 mph (24 km/h).
2
Power Door Lock Switch
If you...
Owner's Manual - Page 38
... doors, press and release the window lock button (setting it in the down position). Window Lockout Switch The window lockout switch on the other doors. Remove the obstacle and use the window switch again to close window manually. For vehicles equipped with the EVIC, the power window switches will remain active...
Owner's Manual - Page 45
... To loosen the lap belt if it could even cut into you can't straighten a belt in a collision.
5. Removing Slack From Belt THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
4. The retractor will withdraw any slack in the belt...., take it to your chest so that it fixed. To remove slack in a collision. Position the shoulder belt on your authorized dealer and have it is straight.
Owner's Manual - Page 47
... belt webbing 180° to create a fold that are taller than average, you will prefer a lower position, and if you release the anchorage, try to remove any slack from the seat belt systems in child restraints. Slide the latch plate upward over the folded webbing. These devices improve the performance of...
Owner's Manual - Page 49
... long as the driver's seat belt is extracted. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49
3. The Enhanced Warning System (BeltAlert) can be necessary to remove any slack in the rear seat whenever possible. Within 60 seconds of turning the ignition switch to turn on while unbuckling the seat belt and...
Owner's Manual - Page 51
... positions.
Only use when the lap belt is not long enough when it is in a collision. Remove and store the extender when not needed can provide you with a seat belt extender. When it is... fully extended, and when the adjustable upper shoulder belt anchorage (if so equipped) is not required, remove the extender, and store it does not come across the abdomen. That way the strong bones of ...
Owner's Manual - Page 168
...top when it is open from a partially closed .
Be sure to clear all objects from the headliner. Anti-Pinch Protect Feature The Sky Slider will close the Sky Slider. WARNING! Wind Buffeting Wind... top closes completely. In the event that your vehicle losses battery power, you must first remove the cargo lamp from the Sky Slider before closing . The left motor facing forward will ...
Similar Questions
How Do I Remove The Headliner In The Rear To Access Antenna
I need to remove the rear moldings and headliner to access antenna, how do I remove them with out br...
I need to remove the rear moldings and headliner to access antenna, how do I remove them with out br...
(Posted by bcwoodbury 11 years ago)