InSinkErator Invite H770-SS Support Question
InSinkErator Invite H770-SS Support Question
Find answers below for this question about InSinkErator Invite H770-SS.Need a InSinkErator Invite H770-SS manual? We have 2 online manuals for this item!
Question posted by cdavidj on May 14th, 2020
Need A New Aerator? Can't Clean The Old One.
new aerator for H770SS .
Current Answers
Answer #1: Posted by freginold on May 14th, 2020 12:47 PM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
Carroll Parts sells a chrome aerator (P/N 44586, $17.64) and a nickel aerator (P/N 44586A, $20.79) for InSinkErator faucets.
Related InSinkErator Invite H770-SS Manual Pages
Specifications - Page 1
Instant Hot Water Dispensers
The Next Necessity™
H770-SS
The original instant hot water dispenser with grounded three (3) ...Max counter thickness is 3/4".
6-3/4"
6-1/8"
Job Specifications
Sample Specification
Instant hot water dispenser(s) shall be InSinkErator Model H770-SS with Lead Plumbing Law
1-800-558-5700 www.insinkerator.com
Printed in USA
The Emerson logo is included in...
Owners Manual - Page 1
TranScape™ View™ TranScape™ Wave™ HC3/GN3 H990 H770
Instant Hot Water Dispenser
Owner's Manual
Installation, Care & Use
Instalacion, cuidado & uso Installation, soin et utilisation
Owners Manual - Page 2
...I For your home.
See Step 1-B. Consult a professional if you 'll enjoy discovering new uses for commercial use of chlorine in your stainless steel sink, you need a 11⁄4" - 11⁄2" hole saw
I Basin wrench I A standard 120... will prevent your dispenser, you may need to local codes. I Make sure that operates the
disposer, unless you intend to it each day.
Owners Manual - Page 3
A potentially hazardous situation, which , if not avoided, will require your instant hot water dispenser and record it here
HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS HC3-SS GN3-SS H990-SS H770-SS
HOW TO USE THIS INSTRUCTION MANUAL
These instructions are separated into main sections, indicated by numbers, and subsections, indicated by -step narrative describing the...
Owners Manual - Page 4
...)
Washers
1-5/8"
1-5/8"
3/4" Screws (2)
2-1/4"
2-1/4"
Rubber Small Steel Large Steel
Fiber
Wing Nut (HC3/GN3 only)
Snap-Connect Fitting (3 pieces)
Tank
3/4" Screws (2)
H990-SS
Semi-Circular Mounting Plate
Wing Nut
Snap-Connect Rubber Gasket Fitting (3 pieces)
Tank
H770-SS
3/4" Screws (2)
Fiber Gasket
Metal Mounting Plate
Snap-Connect Mounting Screw Fitting (3 pieces)
Tank
4
Owners Manual - Page 5
...saw for stainless steel, or you may need to it ? What if you have...SS ...... 25⁄8 3" H-View-SS ........ 25⁄8 3" HC-Wave-SS .... 25⁄8 3" H-Wave-SS ...... 23⁄8 3" HC3-SS 21⁄4 3⁄4" * GN3-SS 21⁄2 3⁄4" * H990-SS .......... 11⁄4 3" H770-SS..., you can cut a mounting hole for your disposer, unless using an InSinkErator SinkTop SwitchTM. I If...
Owners Manual - Page 6
...steel washer over threaded extension. C
Fiber Washer
Hot & Cool models only
Star Nut
An assistant may be needed to the ends of tubing.
I Install a white 3/8" tube into other end of quick connector.
15&#... only
I Feed tubes down through the hole in place.
Do not discard, as you will need this later (See Figure 1).
Set faucet at rest. Thread star nut onto extension until the ...
Owners Manual - Page 7
... order (see diagram): 1) 15⁄8" small steel washer 2) 15⁄8" rubber washer 3) 21⁄4" large steel washer
C
Fiber Washer
Wing Nut
An assistant may be needed to ensure proper operation and seal. D From faucet
3/8" white tube
An extension is at rest.
Do not distort the last 1 inch of the copper tubes...
Owners Manual - Page 8
... of tubing.
I Place wing nut onto the threaded stud. Property Damage: Do not pinch or break copper tubing. 2 INSTALLING THE FAUCET - C
An assistant may be needed to ensure proper seal.
Owners Manual - Page 9
...or break copper tubing. DO NOT remove mounting screw or fiber gasket from base of tubing.
H770
I From below the sink, place semicircular metal mounting plate over so that the fiber gasket is...the dispenser head.
Do not distort the last 1 inch of dispenser.
C
An assistant may be needed to ensure proper seal. D
Half moon shaped metal mounting plate should cradle all descending tubes. ...
Owners Manual - Page 10
...: Pinched or blocked water lines may cause damage to the dispenser tank.
Property Damage: Check to make sure tubes are connected properly and are not needed for any of the connections.
10 I Visually check for hanging tank. DO NOT extend plumbing or electrical lines. I While holding tank in place on the...
Owners Manual - Page 11
... 1/4" tube, slide the brass nut and ferrule provided with the dispenser.
I Insert the copper tube into the 3/8" compression fitting and tighten. H-View / H-Wave / GN3/ H990 / H770
I Check all connections to flush lines (both the hot and cold handles
independently if applicable).
I Insert the white 3/8" tube into the 1/4" compression fitting and tighten...
Owners Manual - Page 12
... consequential damage.
A drain pan, plumbed to an appropriate drain or outfitted with a qualified electrician or serviceman if you . We do not allow limitations on the new unit shall be grounded. Use of your nearest factory authorized service center, call toll free 1-800-558-5700. When service is required, and for the...
Owners Manual - Page 13
...you will result in those applications where any signs of time, unplug and drain unit.
CLEANING THE FAUCET AND TANK
I Only use mild cleaners to your instant hot water dispenser system...leakage. I To put back into working order, install new filter cartridge (if required), fill tank with acids, abrasives, alkaline or organic solvents will need to bring in severe burns. I Empty the tank...
Owners Manual - Page 14
... end piece.
• Unscrew spout end piece and clean out any debris. • Activate faucet lever 7-10 times to reach new temperature. WHAT TO DO
• Activate faucet lever ...valve to check proper mounting washer installation.
POSSIBLE CAUSE
• Unit is not adjusted to your needs.
• Adjust the thermostat slowly, then activate faucet lever for water to flush faucet & lines...
Similar Questions
Need The Rubber Seal For Badger 5 Disposal
the seal at the discharge of Badger 5 disposal leaks.
the seal at the discharge of Badger 5 disposal leaks.
(Posted by hmarta 6 years ago)
Why Water Leaks From Vent Hole On Faucet
(Posted by dmsears90 9 years ago)
Why Is My Garbage Disposal Leaking On The Bottom
(Posted by shrnwashington 10 years ago)
Ball Bearing In Garbage Disposal
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
We heard a bad sound and found two ball bearing inside our disposal that we did not put in?? It is a...
(Posted by Gbobeczko 11 years ago)
Dishwasher Is Not Draining After Installing The Garbage Disposal.
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
Have checked the dishwasher drainage and there is no problem. There appears to be a blockage on the ...
(Posted by Drkisa 11 years ago)