Husqvarna ST 121E Support Question
Husqvarna ST 121E Support Question
Find answers below for this question about Husqvarna ST 121E.Need a Husqvarna ST 121E manual? We have 1 online manual for this item!
Question posted by daveeverhart0506 on February 13th, 2020
My Lights Wont Work. Ive Replaced Bulbs With No Luck. Please Help... Thank You
The person who posted this question about this Husqvarna product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Odin on February 13th, 2020 12:41 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,680
Member since:
April 10th, 2010 Points: 41,236,680
See Lights not On at Https://www.manualslib.com/manual/673616/Husqvarna-St-121e.html?page=61#manual. If the issue persists of if you require further advice, or if those instructions do not seem to apply to your model, you'll have to consult Husqvarna. (You can if necessary find contact information at https://www.contacthelp.com.)
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Husqvarna ST 121E Manual Pages
Owners Manual - Page 2
... experience any adjustments while the engine (motor) is spilled on a trailer with a portable container, rather than from a gasoline dispenser nozzle.
(f) Keep the nozzle in reverse.
(g) Replace gasoline cap securely and wipe up , transporting, adjusting or making repairs. We have exposed rotating parts, which can get caught in order to service or...
Owners Manual - Page 3
...manual. Never operate the snow thrower without good visibility or light. never run the engine indoors, except when starting the ... safety rules.
• Follow a regular schedule in place and working condition.
2. When cleaning, repairing or inspecting the snow thrower, ...FUTURE REFERENCE. SHUT THE ENGINE OFF!
2. Maintain or replace safety and instruction labels, as hot water heaters, space...
Owners Manual - Page 4
... YOUR SNOW THROWER. IGNITION KEY. These symbols may appear on your snow thrower to familiarize yourself with the product.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
4 Replace damaged decals. Learn and understand their meaning. INSERT TO START AND RUN
CHOKE CLOSED (START)
PRIMER
RECOIL START
CHOKE OPEN (RUN)
IGNITION KEY. Save this...
Owners Manual - Page 7
.... Owner's Manual
* Dipstick location may vary depending on engine type.
13 *7 14
7 Discharge chute 2. Control bar 13. Auger blade 16. Recoil start button
(if equipped) 6. Lights 14. Product Overview
10 1
94
PRODUCT OVERVIEW
2 12
11 16
3
17
8
*7 6
5
15
Figure 8
1. Ignition key 10. Chute rotator handle 11. Choke lever
9. Drive side cover...
Owners Manual - Page 9
... push the electric-start button (Figure 12).
1
The electrical cord can overheat and damage it each time. Thoroughly inspect the electrical cord before releasing it . Replace or repair the damaged cord immediately.
Thaw out the starter before attempting to the snow thrower and plug the other end into a power source. Move...
Owners Manual - Page 11
... thrower.
• The best time to remove snow is usually dry and has not been exposed to operate frozen controls. Do not use . This will help air flow and extend engine life.
• After snow-throwing is ready for all moving parts may freeze. OPERATION
2. Wait 10 seconds to be hazardous...
Owners Manual - Page 12
... disengage the control bar for Loose Fasteners Clean / Inspect Snow Thrower Clean / Replace V-Belts Check / Replace Auger Blades and Scraper Bar Check Fuel Lines and Electrical Wires Check Engine Oil Level Change... Engine Oil Inspect Muffler Check / Replace Spark Plug Empty Fuel Tank
Adjusting the Control Cable
CHECKING THE CONTROL CABLE
1.
...
Owners Manual - Page 13
...have to warm it
(Figure 25). 9. NOTE: Dipstick location may have an Authorized Service Dealer replace the auger blades and the scraper bar (Figure 22).
With the snowthrower in -lbs (17...drain the used oil, return the snowthrower to a level surface. 2. The engine oil will be replaced after extended use.
5. Dispose of SJ, SL, or higher. MAINTENANCE
Inspecting the Auger Blades/ Scraper...
Owners Manual - Page 14
... section of ignition switch (Figure 29).
13. Remove 2 screws in plenum that it to the side of the primer bulb.
24
24
4
1. Pull tube off the back of the unit. Primer bulb
14. Wait until engine is clear of the rear upper cover and set top cover to the upper cover.
14...
Owners Manual - Page 15
...two screw holes line up with the hardware removed
in the side covers that attach to primer bulb and electrical wires on the side cover (Figure 27). Remove top oil fill cap. 25..... Figure 30
1. Remove the spark plug from the spark plug (Figure 30).
16. Spark plug wire
IMPORTANT: Replace a cracked, fouled, or dirty spark plug. Install the spark plug and torque it to 0.030 inch (0.76 ...
Owners Manual - Page 16
... adjusted and operating; Idler pulley 3. Engine pulley 4. refer to drive pulley and has left handed threads.
3. MAINTENANCE
Replacing the Auger V-Belt
If auger v-belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt.
1. Idler arm
5. Drive pulley
NOTE: Ensure that the auger v-belt is welded to Checking the...
Owners Manual - Page 17
... of oil through spark plug hole into cylinder.
3. ENGINE OIL
Drain oil (with engine warm) and replace with a suitable protective cover that all dirt, grease, leaves, etc. CYLINDER
1. OTHER
• Remove...products in the fuel tank or permanent damage may reach an open flame, spark or pilot light as carburetor, fuel hose, or tank during storage. Do not use plastic. STORAGE
Storage
STORING...
Owners Manual - Page 18
...10. remains, contact an authorized service center/department. Adjustment lever nuts are not kinked. Recoil starter is cool). Check / replace auger v-belt.
4.
Loose wire connection.
1. Check wire connections at engine and both lights.
3. Debris in OFF position.
4. Clean internal parts of power
1. Safety ignition key is disconnected. 7. Choke in chute rotator mechanism...
Owners Manual - Page 20
REPAIR PARTS SNOW THROWER - - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. MODEL NUMBER ST 121E (96183000100) HANDLE ASSEMBLY
1 2
4 5
20 3
20 21
20
9
19
7
10
12
12
13
17
15
14 14
15
16
16
18
17
8
7 11
NOTE: All component ...
Owners Manual - Page 21
...BOLT.HEX.WSH 13-16 X 3/4 WASHER.9/32 X 5/8 X 16 GA
NOTE: All component dimensions given in U.S. MODEL NUMBER ST 121E (96183000100) HANDLE ASSEMBLY
KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ...2 2 1 1 8 4
DESCRIPTION
SUBASM.CONTROL.SHROUD COVER.HANDLE.LG.SHROUD BRACKET.SUPPORT - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Owners Manual - Page 22
MODEL NUMBER ST 121E (96183000100) CHUTE ASSEMBLY
8 9 10
5 4 3
7 98 6
10 10
5 2
1
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
22 REPAIR PARTS SNOW THROWER - -
Owners Manual - Page 23
MODEL NUMBER ST 121E (96183000100) CHUTE ASSEMBLY
KEY NO. 1 2 3 4 5 6 7 8 9 10
PART NO. 817 41 13-12 532 44 34-25 819 13 13-16 532 42 88-67 872 ... be hazardous, damage your snow thrower and void your warranty.
23 REPAIR PARTS SNOW THROWER - - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Owners Manual - Page 24
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
24 REPAIR PARTS SNOW THROWER - - MODEL NUMBER ST 121E (96183000100) CHUTE ROTATOR CONTROL ASSEMBLY
13 5
6 2 6 5
2
2
2
4
8 7
3
12 11 10
9 10
9
1
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Owners Manual - Page 25
MODEL NUMBER ST 121E (96183000100) CHUTE ROTATOR CONTROL ASSEMBLY
KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13
PART NO.
532 43 68-05 532 43 68-06 532 43 48-75 ... be hazardous, damage your snow thrower and void your warranty.
25 REPAIR PARTS SNOW THROWER - - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Owners Manual - Page 27
...replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
27 SCREW.HI-LO TORX.1/4-20X3/4.SCREW TANK.FUEL.ASM TIE.CABLE.24.5X.29.NYLON.WHITE COVER.REAR.LOWER KEY CLIP CLIP HANDLE.STARTER
NOTE: All component dimensions given in U.S. MODEL NUMBER ST 121E...FR.N/CB.E10 BULB.PRIMER KEY HOUSING TOP.REAR.COVER PLATE.EXHAUST.PNT. REPAIR PARTS SNOW THROWER -...
Similar Questions
Light
There is a small set of light switches located above to the right and above the steering wheel. the ...
There is a small set of light switches located above to the right and above the steering wheel. the ...
(Posted by espencer46625 4 years ago)
Snow Throw Blades Not Engaging. Cable To Handle Loose.
Is there a way I can fix. Something must have come loose.
Is there a way I can fix. Something must have come loose.
(Posted by jimc6937 7 years ago)
Fuel Line From Prime Bulb Has Hole In It. How Do I Replace The Fuel Line?
(Posted by djember47 9 years ago)