Hunter 44550 Support Question
Hunter 44550 Support Question
Find answers below for this question about Hunter 44550.Need a Hunter 44550 manual? We have 2 online manuals for this item!
Question posted by unitegr on June 24th, 2014
Thermostat Manual What Does Recovery Mean
The person who posted this question about this Hunter product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hunter 44550 Manual Pages
Owner's Manual - Page 1
SINCE
®
1 8 8 6
AUTO SAVER 550
5:22
3 72
OwnerÕs Manual
Model 44550
Owner's Manual - Page 3
... assistance, call Hunter Technical Support at 901-745-9222 from 8 a.m. If you for buying a Hunter product! Introduction
CONGRATULATIONS! By saving energy, your thermostat.
to 5 p.m. Model Information: Model Number ____4_4_5_5_0 Serial Number Date Purchased Where Purchased Please read this manual for itself during its first season of reliable service. Your new Hunter electronic...
Owner's Manual - Page 4
Table of Contents
INTRODUCTION INSTALLATION
PROGRAMMING
OPERATIONS
Read This Before Installing Thermostat Features
What You Need Remove Old Thermostat Wire Labeling Mount Wallplate and Thermostat Selector Switches
Setting Time and Day Auto Programming Personal Program Schedule Manual Programming Weekday / Weekend Programming 7-Day Programming Reviewing Programs Reviewing the Current Temperature ...
Owner's Manual - Page 5
Table of Contents (continued)
OPERATIONS (continued)
Temporary Manual Override
24
Permanent Manual (Vacation) Override
25
Auto Season Changeover
26
Home Today
26
Energy Monitor
28
Filter Monitor
29
Auto Recovery
30
Keyboard Lock
31
Backlighting
31
SAFETY FEATURES
Low Battery Warning
32
Error Mode
33
Auto Cut-Off
33
TROUBLESHOOTING
Problems & Solutions
34
Technical...
Owner's Manual - Page 6
....
INSTALLATION
2 All installation is lower than 99°F (37°C), and "LO" will be treated as a Permanent Manual Override. Note that do not have 24-volt or millivolt control systems and
COMPRESSOR PROTECTION
5 The thermostat provides a 3.5 minute delay after shutting off the heating or cooling system before installation by rapid cycling. TEMPERATURE...
Owner's Manual - Page 7
...: If you replace the old batteries with the current time. Read This Before Installing Thermostat (continued)
POWER FAILURE
7 Whenever the main power is set from the factory to ...gradually recover the room temperature from the premises over one year of your dwelling. AUTO RECOVERY
8 Your thermostat is interrupted or fails, the battery power retains the programs and current time. You
...
Owner's Manual - Page 8
... or Continuous On fan operation. Battery Door: Frontaccess battery door allows easy battery changes. HOME TODAY: Overrides energysaving program temperatures while you can program the thermostat to allow display viewing in the dark. Features
8-9
Light Bar: Activates INDIGLO® night-light to optimize energy savings.
Owner's Manual - Page 9
...
PROG DAY
MIN
DAY
AUTO PROGRAM
HOLD CLEAR
FILTER RETURN
Automatically programs the thermostat to current time and temperature. Reviews filter usage in Program Mode. See page... counter to current program control from manual override or Home Today mode. As an ENERGY STAR® Partner, Hunter Fan Company has determined that this programmable thermostat meets the ENERGY STAR® guidelines...
Owner's Manual - Page 10
...wires and mounting screws. (See Figure 1). TYPICAL HOME THERMOSTATS Figure 1
Wall Mounting Plate
Thermostat
Cover
Wall Mounting Plate
Thermostat
Cover Some thermostats will have doors that must first be connected to the ...furnace at the main power panel or at the furnace. To install your thermostat, you should have the following tools and materials. s IMPORTANT! Again, look for...
Owner's Manual - Page 11
...the wire which goes to the W or H terminal on
your existing thermostat.) IGNORE THE
COLOR OF THE WIRES since these existing thermostat is with label shown terminal shown
terminal points is often no hot ...Wire Labeling
s Each wire coming from the wall to the existing thermostat is larger than necessary for wires, seal this hole so that thermostat. RH, R, VR or 4 24 Volt
RH
RH
RH
If...
Owner's Manual - Page 12
... (5-wire system), then remove the jumper wire between the RH and RC terminals on the Hunter wallplate. INSTALLATION
12-13
Mount Wallplate and Thermostat
s Remove the wallplate from your thermostat has one wire marked R or RH (4-wire system), then leave the jumper wire between the RH and RC terminals. s Reposition wallplate to...
Owner's Manual - Page 14
...to customize the features to OFF before removing the thermostat from the wall. If your reversing valve that ...thermostat calling for certain electric systems having a fan relay. switch
HG - s Furnace or Heat Pump selector (NORMAL - If you have a single-stage Heat Pump (no effect in COOL mode.
B - O - F°/C° selector 12 Hr./24 Hr.
(SW5)
selector
(SW6)
Recovery...
Owner's Manual - Page 15
... the switch to the 24 position. A similar table is set for normal 12 hour (AM / PM) time format. Switch 7 Your thermostat is pressed, the thermostat will automatically change temperature mode. Span
Auto Recovery
Switch Setting
Alternate
Standard
Celsius
Fahrenheit
24 Hour
12 Hour
+2°F / -1°F
+1°F / -1°F
Disable
Enable NOTE: Unless the reset...
Owner's Manual - Page 17
...;F (29°C)
3
4:00pm
68°F (20°C)
78°F (26°C)
4
10:00pm
60°F (16°C)
82°F (28°C)
s Refer to program the thermostat manually.
You can program all 7 days of 4 programs. Similarly weekend programs, Saturday and Sunday, can be programmed for instructions on page 19 for all weekdays, Monday...
Owner's Manual - Page 19
... mode.
6) When setting the program time, note the AM / PM indicator.
7) With the Auto Recovery feature enabled, you can not be set lower than the Heat setpoint.
4) If the system selector is in Cool mode. Manual Programming
s Your thermostat can be used when entering programs for the first time, or revising programs entered...
Owner's Manual - Page 23
...SET TEMP
AM
°C
PM
H
Refer to normal mode. s After 15 seconds, the thermostat will be blank when at least one of the
weekend programs is shown above current room temperature...., Temporary Manual Override mode is different. If you are armchair programming the thermostat, slide the system selector to the OFF position before mounting the thermostat to display M - s Thermostat is set...
Owner's Manual - Page 24
... warmup delay.
At the next program change to signify the Temporary Override.
NOTE: Anytime you install or remove the thermostat from the wallplate, slide the System Selector to the OFF position to enter Manual Override mode. For electric heat, air conditioning, and heat pump operation, the Fan will be turned on page...
Owner's Manual - Page 25
...26 for more information. NOTE: The Auto Season Changeover feature will not operate while the thermostat is in Temporary Manual Override. H O : L D M T W Th F Sa Su SET TEMP
AM
&#... the
HOLD CLEAR
flashing HOLD display will not operate while the thermostat is in Permanent Manual Override.
The thermostat will return to make the current program's temperature the HOLD temperature...
Owner's Manual - Page 27
... period, the setpoint temperature will not affect the Home Today ending time.
"HOME" is no longer displayed on the LCD screen, and the thermostat returns to the Temporary Manual Override instructions on page 24. s You may similarly extend it to the first program of the third program.
Refer to the current program...
Owner's Manual - Page 30
... note the temperature difference between heat and cool (automatically or manually) then the thermostat will not operate if Permanent hold, Temporary hold or Home Today is pressed during the recovery process. s Auto Recovery will recalculate Auto Recovery again. s Auto Recovery will be canceled and change to Temporary Manual Override mode if the setpoint is pressed during the...
Similar Questions
