Hoover U8181 Support Question
Hoover U8181 Support Question
Find answers below for this question about Hoover U8181.Need a Hoover U8181 manual? We have 1 online manual for this item!
Question posted by llsmith5449 on December 19th, 2012
Hoe To Replace The Belt On A U8181-900
The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hoover U8181 Manual Pages
Manual - Page 1
www.hoover.com
®
This product was designed for your purchase!
TM
Upright Vacuum Cleaner
by HOOVER
Owner's Manual
ENGLISH § pp.1-12 ESPAÑOL § pág. 14-21 FRANÇAIS § p. 23-30
Thank you for easy assembly (see page 3)
Manual - Page 2
...Cleaning filter 8 Emptying Dirt Cup 7 Replacing Powered Hand Tool
Agitator Brush Roll 10 Replacing Power Hand Tool Belt ..10 Replacing Edge Groomers 9 Replacing Headlight 9 Thermal Protector 11 Warranty 12...Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot).
• Use vacuum cleaner only for its intended use . Verification of date of purchase may cause ...
Manual - Page 7
...dirt cup.
Turn knob (G) on back of dirt cup lid one full turn. Replace dirt cup lid.
Remove cup - The HEPA cartridge filter will stop larger debris from entering the HEPA cartridge ...filter chamber.
Replace cup - Press firmly until no more dust particles fall from electrical outlet.
Slide ...
Manual - Page 8
...lid as described in "How to ensure that filter assembly is seated properly in "How to replace this filter, ask for additional cleaning. Grasp pre-filter frame and pull up on bottom of ...Note: If dirt cup lid does not close all the way, ensure that it away from assembly. Replace door.
The filter assembly can be removed for HOOVER part No. 40110009.
Turn knob on pre-filter ...
Manual - Page 9
... Press on lens and secure other tab.
3-18
The agitator brush rolls
3-16
When to replace
The edge groomers, located on both old edge groomers and slide new edge groomers into slots ...plate into position as shown. Continued §
9
To maintain cleaning effectiveness, have brush rolls replaced if brushes do not touch card. Lift lens off both sides of flat screwdriver into slots ...
Manual - Page 10
... either side of brush roll into slots on tool. However, if the belt is in guard.
With flat sides of tool. Remove agitator including end plates (C) and discard. 4. Replace belt
When replacing belt, ask for HOOVER part No. 48414088.
3-21
A
3-22
B
2. Replace with new belt.
8. Turn agitator, to pinch brush bristles in good condition. Unscrew the two...
Manual - Page 11
...this happens, proceed as described in turbine channel • Remove blockage. • Broken or worn belt • Replace belt • Low cleaner suction • Check items under "Cleaner won 't turn on BARE FLOOR ... • Check fuse or breaker
• Blown fuse or tripped breaker • Replace fuse or reset breaker
• Thermal protector activated • Allow cleaner to the ...
Manual - Page 12
.... 5. Turn cleaner over and clear blockage from dirt duct.
4-2
Check brush rolls 4. Replace belt turbine, brush roll, belt guard and bottom plate. This warranty provides, at www.hoover.com OR -
• calling...locations (U.S. however, if you may be obtained by :
• checking the Yellow Pages under "Vacuum Cleaners - Remove dirt cup, look in Figs. 3-21, 3-22 and 3-28. Look into hose...
Similar Questions
Video How To Replace Belt On Hoover Turbo Cyclone Vacuum Model Uh70055
(Posted by greaHellS 9 years ago)
How To Change The Agitator Belt?
the belt in my hoover savvy broke a few days ago. i have the replacement belt but i am having issues...
the belt in my hoover savvy broke a few days ago. i have the replacement belt but i am having issues...
(Posted by alphasigs819 10 years ago)