Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by yvonne5643 on September 13th, 2016
What Does It Mean When The # 3 Is In The House Symbol On The Thermostat?
We replaced the furnace filter last night but there is a house symbol on the thermostat and the air conditioner is not cooling off the house.
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
... wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system. Quick Installation Guide
Installation is Easy
Your new thermostat has been designed for fast and easy installation. Call 1-800-468-1502.
1 Do you need assistance...
Owner's Manual - Page 3
...; a central heating and cooling system
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. RTH2310 Programmable Thermostat
1 Identify System Type
1.
This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water...
Owner's Manual - Page 4
... remove wallplate yet. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Quick Installation Guide
2 Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
... only after all wires are attached to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled.
If any wires are not attached to your new thermostat. Do not use non-connected wires.
Wrap the wires around a pencil to identify wires. Do not use C or C1...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors.
Owner's Manual - Page 7
If a wire does not match any excess wire back into the wall opening. RTH2310 Programmable Thermostat
5 Connect Wires (typical wiring) 5. Labels don't match? Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the ...
Owner's Manual - Page 9
RTH2310 Programmable Thermostat
7 Specify Furnace Type
6. Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. HE Place the jumper to the G terminal.
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8
Owner's Manual - Page 10
...
7.
1) Pull out the battery cover. 2) Install the batteries as shown. Observe the
polarity. 3) Reinstall the battery cover. Afterwards, the screen displays the actual temperature. The thermostat will hear a clicking
sound. You will display the ambient temperature once it is 70 °F (21 °C).
9 By default, the setpoint is installed on the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...(hot water, 90%+ high-efficiency furnace), 4=15 min (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).
5 The corresponding cooling cycle lengths are shown in U.S.A. Quick... h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are as follows: 2=30 min, 3=20 min, 4=15 min...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
What Does It Mean When The #2 Symbol Is In The House Symbol?
(Posted by rwsmith65312 2 years ago)
No Cool Symbol
I have set my thermostat on cool and programmed temp and time but when I save the settings the cool ...
I have set my thermostat on cool and programmed temp and time but when I save the settings the cool ...
(Posted by theisennl 6 years ago)
What Does The Snowflake Mean On My Honeywell Thermostat
(Posted by openwtx 10 years ago)
What Does It Mean When Snowflake Symbol On Honeywell Thermostat Flashes
rth2310b
rth2310b
(Posted by barnh 10 years ago)
What Does A Flashing Snowflake Mean On A Honeywell Thermostat
(Posted by jkneohs 10 years ago)