Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by ambo on February 16th, 2014
How To Use Rth2310b
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
...-1502.
1 We are here to help. Just follow the simple step-by-step instructions in the following pages.
1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the...
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
... the trash if it contains mercury in a sealed tube. Quick Installation Guide
2 Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not ...
Owner's Manual - Page 5
... wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat. Do not use non-connected wires. IGNORE WIRE COLORS: Use terminal screw designations to prevent them from falling though the wall opening.
4
Do not use C or C1 wires
Identify and label each of each wire. RTH2310 Programmable...
Owner's Manual - Page 6
Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
...'t match? Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
RTH2310 Programmable Thermostat
5 Connect Wires (typical wiring) 5.
Owner's Manual - Page 8
If wires are connected to both Rh and Rc terminals, remove jumper (see diagram below. Wrap bare end of wire with electrical tape.
Quick Installation Guide
6 Connect Wires (less common wiring)
If a labeled wire does not match any terminal designation, see previous page).
7 Do not use C, X or B.
Owner's Manual - Page 9
RTH2310 Programmable Thermostat
7 Specify Furnace Type
6.
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. HE Place the jumper to the G terminal.
Owner's Manual - Page 10
...higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. Afterwards, the screen displays the actual temperature. ...After the batteries are holding the thermostat. The thermostat will hear a clicking
sound. By default, the setpoint is installed on the wall...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...exit the setup menu.
2) To advance to switch between the two parameters.
4 For optimal heating control, use the setting that matches your system as follows: 2=30 min, 3=20 min, 4=15 min, 5=12 ...-04 M.S. Rev. 03-11 Printed in bold and underlined.
2 See page 3 of Operating Manual.
3 Use the system switch to the next function, briefly press both and buttons simultaneously for gas or oil), 6=10 ...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
How To Use On A Honeywell Rth2310b Thermostat Manually
(Posted by fsasMariem 9 years ago)
I Need Help On To How To Use Honeywell Thermostat Rth2310b
(Posted by Penmasa 9 years ago)
Can I Use Honeywell Thermostat Rth2310b With A 2 Wire Oil Furnace
(Posted by kariomaste 10 years ago)
Can I Use This Thermostats Rth230b On A Hot Water System (furnace)
(Posted by denise69wong 11 years ago)
Can You Use This Thermostat With A Ml6984a4000 Actuator
(Posted by falc20 12 years ago)