Home » Honeywell » Thermostats » Honeywell RTH2310B

Honeywell RTH2310B Support Question

Find answers below for this question about Honeywell RTH2310B.
Need a Honeywell RTH2310B manual? We have 1 online manual for this item!

Honeywell Overview Questions Manuals Reviews Videos Research

Question posted by pacontino on July 10th, 2014

How Do I Turn Off Programming On A Honeywell Rth2310b Thermostat

I want to work it manually

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Honeywell RTH2310B Manual Pages

Owner's Manual - Page 1

Quick Installation Guide RTH2310 Programmable Thermostat 69-2214EF-04

Owner's Manual - Page 2

... the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system. We are here to help. Quick Installation Guide Installation is Easy Your new thermostat has been designed for fast and easy installation. Do you need assistance? Call 1-800-468-1502. 1

Owner's Manual - Page 3

... the following systems: • Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems. 2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system If you are not sure of your system type...

Owner's Manual - Page 4

... your local waste management authority for instructions regarding recycling and proper disposal. 3 Quick Installation Guide 2 Remove Old Thermostat 2. 1) Turn power off at the heating/cooling system. 2) Remove old thermostat, but leave wallplate with wires attached. Contact your old thermostat in the trash if it contains mercury in a sealed tube. Do not remove wallplate yet.

Owner's Manual - Page 5

RTH2310 Programmable Thermostat 3 Identify Wires 3. Wrap the bare metal end of each wire. Do not use C or C1 wires Identify and label each of these wires...remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat. Wrap the wires around a pencil to identify wires. If any wires are not attached to your old...

Owner's Manual - Page 6

Quick Installation Guide 4 Mount New Wallplate 4. 1) Remove coverplate. 2) Loosen screw (the screw remains captive on wallplate). 3) Remove thermostat. 4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws. 5 Insert plastic anchors.

Owner's Manual - Page 7

... with the terminal having the same letter. 2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws. 3) Push any terminal on the thermostat, see next page. 6 Labels don't match? RTH2310 Programmable Thermostat 5 Connect Wires (typical wiring) 5. If a wire does not match any excess wire back into the wall opening.

Owner's Manual - Page 9

J2 jumper HG Leave the jumper in this position if you have an electric furnace. 8 RTH2310 Programmable Thermostat 7 Specify Furnace Type 6. Set the Jumper J2, on the back of the thermostat, if you have connected a wire to the G terminal. HE Place the jumper to this factory-set position if you have a gas or oil furnace.

Owner's Manual - Page 10

... hear a clicking sound. By default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. It is 70 °F (21 °C). 9 Observe the polarity. 3) Reinstall the battery cover. Quick Installation Guide 8 Install Batteries 7. 1) ...

Owner's Manual - Page 11

RTH2310 Programmable Thermostat 9 Install thermostat 8. 1) Mount the thermostat on the wallplate. 2) Tighten the screw and install the coverplate. 3) Turn power back on at the heating/cooling system. 10

Owner's Manual - Page 12

... 9. 1) Press both and buttons simultaneously. 3) To change the setting, press the or button. Rev. 03-11 Printed in bold and underlined. 2 See page 3 of Operating Manual. 3 Use the system switch to the next function, briefly press both and buttons simultaneously for 3 seconds to enter or exit the setup menu. 2) To advance...

Owner's Manual - Page 13