Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by kitterkinz on June 9th, 2015
Battery Change Problem
blank display and no backlite
Current Answers
Answer #1: Posted by TechSupport101 on June 10th, 2015 6:33 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Battery installation guide for the model available here http://www.manualslib.com/manual/423744/Honeywell-Rth2310b.html?page=10&term=batteries&selected=1 and failure to funtion of the thermostat, inspite proper batties replacement should indicate a mechanical failure.
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
... easy installation. Call 1-800-468-1502.
1 Just follow the simple step-by-step instructions in the following pages.
1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the...
Owner's Manual - Page 3
... not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. RTH2310 Programmable Thermostat
1 Identify System Type
1. This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps...
Owner's Manual - Page 4
... power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Contact your old thermostat in the trash if it contains mercury in a sealed tube. Do not remove wallplate yet...
Owner's Manual - Page 5
... after all wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat. RTH2310 Programmable Thermostat
3 Identify Wires
3. If any wires are not attached to your old thermostat or are labeled. IGNORE WIRE COLORS: Use terminal screw designations to prevent them from falling though the wall opening...
Owner's Manual - Page 6
Insert plastic anchors. Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 If a wire does not match any excess wire back into the wall opening. RTH2310 Programmable...
Owner's Manual - Page 9
HE Place the jumper to the G terminal. J2 jumper
HG Leave the jumper in this position if you have connected a wire to this factory-set position if you have an electric furnace.
8
RTH2310 Programmable Thermostat
7 Specify Furnace Type
6. Set the Jumper J2, on the back of the thermostat, if you have a gas or oil furnace.
Owner's Manual - Page 10
...70 °F (21 °C).
9 Afterwards, the screen displays the actual temperature. Observe the
polarity. 3) Reinstall the battery cover. After the batteries are holding the thermostat. By default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... and buttons simultaneously for gas or oil), 6=10 min (electric).
5 The corresponding cooling cycle lengths are shown in U.S.A. DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 ... briefly press both and buttons simultaneously.
3) To change the setting, press the or button.
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
How To Change Honeywell Thermostat Rth2310b Manual From C To F
(Posted by admgraf 10 years ago)
What Are Battery Changing Steps?
What are the battery changing steps on a Honeywell TH6110D1005-U thermostat?
What are the battery changing steps on a Honeywell TH6110D1005-U thermostat?
(Posted by bernardo84549 10 years ago)
How To Change Battery In Honeywell Thermostat Manual Rth2310b
(Posted by colojw 10 years ago)
Blank Display Screen
Thermostat in one part of the house shows a blank display and the cooling system was not operating. ...
Thermostat in one part of the house shows a blank display and the cooling system was not operating. ...
(Posted by schade5 11 years ago)