Honeywell PRO22IC Support Question
Honeywell PRO22IC Support Question
Find answers below for this question about Honeywell PRO22IC.Need a Honeywell PRO22IC manual? We have 1 online manual for this item!
Question posted by cristiandorobantu on June 1st, 2012
Communication Rs 485 Problem
Good Morning,In one control acces system I have 8 PRO22IC cards. The cards have been parameterized identically (normal, except addresses). Four cards comunicates at level on bus RS485 and the other four no.Can you advice me what to try in order to have comunication on all 8 cards?Best regards, Cristian Dorobantu
Current Answers
Related Honeywell PRO22IC Manual Pages
Installation Manual - Page 3
PRO-2200 Intelligent Controller PRO22IC
Installation Guide
3
Contents
Warnings and Cautions 4 Disclaimer...6 Unpacking Procedure 6 Shipping Instructions 7 Limited Warranty 7 Confidentiality ...8 Description ...9 Set Up ...9 LED Operation 10 Power...10 Communications 11 Alarm Inputs...12 Memory Backup Battery 12 Mounting Options 12 Suggested Installation Sequence 12 Specification ...
Installation Manual - Page 4
...using the PRO-2200 or related products for damages to the end user if a problem occurs. DO NOT ACCEPT VERBAL APPROVALS, THEY ARE NOT VALID. Engineered Systems Group ...as a primary warning or monitoring system. WARNING
Fire Safety and Liability Notice
Never connect card readers to the system. 4
Installation Guide PRO-2200 Intelligent Controller PRO22IC
Warnings and Cautions
WARNING
...
Installation Manual - Page 5
... integrated circuits and modules. Operation of this equipment in a residential area is subject to radio communications. NOTICE
This document and the data in which case the user will be duplicated, used in a commercial environment. PRO-2200 Intelligent Controller PRO22IC
Installation Guide
5
CAUTION
IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST BE...
Installation Manual - Page 6
... other defect is noticed before unpacking, a claim must be filed with the acts or omissions of the equipment, if needed.
2. 6
Installation Guide PRO-2200 Intelligent Controller PRO22IC
Disclaimer
Product Liability; Unpacking Procedure
CAUTION
If any component thereof has caused personal injury or damage to the shipment is apparent, call 800-323-4576...
Installation Manual - Page 7
...number if the unit is not under normal use. All warranty work shall be...Communications Products and Upgrade kits is determined to Engineering Systems by Engineering Systems include a warranty registration card... RMA number on behalf of the problem or reason for shipment. Packages, ... SYSTEMS' PRODUCTS. PRO-2200 Intelligent Controller PRO22IC
Installation Guide
7
Shipping Instructions
To ship...
Installation Manual - Page 8
... the Products shall remain confidential and shall constitute proprietary rights of and only during the time it sells the Products. 8
Installation Guide PRO-2200 Intelligent Controller PRO22IC
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other party.
Installation Manual - Page 9
... configuration and card holders, and the event log buffer in FLASH memory and may be changed without physically changing board components. The program is stored in battery-backed memory. These jumpers/switches setup the memory chip size, port interface, end of line termination, controller address, and baud rate. PRO-2200 Intelligent Controller PRO22IC
Installation Guide...
Installation Manual - Page 10
...Controller PRO22IC
DIP Switch Settings:
S8 S7 S6 S5 S4 S3 S2 S1
SELECTION
OFF OFF OFF ON ADDRESS 1
OFF OFF ON OFF ADDRESS 2
OFF OFF ON ON ADDRESS 3
OFF ON OFF OFF ADDRESS 4
OFF ON OFF ON ADDRESS 5
OFF ON ON OFF ADDRESS 6
OFF ON ON ON ADDRESS 7 OFF OFF OFF OFF ADDRESS...
FLASH
FLASH
FLASH
DESCRIPTION
Start Power-up sequence and normal operation. Flash when there is activity on Host Port...
Installation Manual - Page 11
... this port is selected as possible. Up to eight boards can be downgraded to eight controller boards can share one PRO22IC per port). Port 1 may use one of three communications specifications:
RS-232-When this signal is RS-485.
Install termination jumper only for port 1 is required and NOT optional. TXD indicatesTransmit and is set to...
Installation Manual - Page 12
... For N-485 Communication Connections, ...Controller PRO22IC
For Wiring to the TR- GND is closed contact.
The normal (non-alarm) condition is the signal ground. The wiring for the network. use as your data pair, observing polarity. When daisy-chaining RS-485...of the four corners of cabinet tamper and power fault monitoring. Use 24 AWG low capacitance, two twisted-pair, shielded...
Installation Manual - Page 13
...RS-485 (9,600 to PC, central station, modem or printer. 9. Setup the panel controls using the host software.
Install the PRO22EN and/or PRO22M4 option boards per this board is being mounted in low voltage, class 2 circuit only. Connect communications... storage 0 to 85% RHNC PRO-2200 Intelligent Controller PRO22IC
Installation Guide
13
Suggested Installation Sequence
1.
WARNING: ...
Installation Manual - Page 14
... side ONLY!
use as your data pair, observing polarity. 14
Installation Guide PRO-2200 Intelligent Controller PRO22IC
Wiring Diagram
Tamper Switch (In Close Position when Cabinet Door Is Closed)
+12VDC Power Supply
PWR + PWR - No Charging - RS 485
Com
Bus Cable To Other Panel
NC
Note
Connect to the appropriate earth ground on one side...
Similar Questions
Everyday At Same Time (afternoon) We Have To Give The Code In Order To Get Off T
Dear madam/sir,We use XK108 system since 8 years. We have changed the AC two weeks ago. We do not us...
Dear madam/sir,We use XK108 system since 8 years. We have changed the AC two weeks ago. We do not us...
(Posted by suleymankose 5 years ago)
How To Shut Off The Beep Sound When The Door Opens On My Fbii Xl Security Alarm
How do you shut off the beep sound that occurs when the door open opens but the alarm is no engaged ...
How do you shut off the beep sound that occurs when the door open opens but the alarm is no engaged ...
(Posted by sacsmom7 9 years ago)
How Do I Check My Glass Break Sensors For Problems For Fbi Model Xl 4600 Sm
home alarm security system
home alarm security system
(Posted by Padmz 9 years ago)
How To Solve The Problem Of Sensing Beeping During Disarmed?
(Posted by chuckyang99 11 years ago)
Have A Old Honeywell/westinghouse Security System And It Keeps Beeping
HONEYWELL XL4600SM FLASHING AC/LB AND BEEPS EVERY 15 MINUTES OR SO, WHAT CAN I DO TO STOP IT?
HONEYWELL XL4600SM FLASHING AC/LB AND BEEPS EVERY 15 MINUTES OR SO, WHAT CAN I DO TO STOP IT?
(Posted by EMJWIN 12 years ago)