Hitachi c15fb Support Question
Hitachi c15fb Support Question
Find answers below for this question about Hitachi c15fb - 15 Amp Miter Saw No Bevel.Need a Hitachi c15fb manual? We have 1 online manual for this item!
Question posted by luicha on September 16th, 2011
I Have A New Switch For My Hitachi C15fb I Need A Diagram To Rewire It
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by kcmjr on September 16th, 2011 2:42 PM
kcmjr
Member since:
May 5th, 2011 Points: 4,254,255
Member since:
May 5th, 2011 Points: 4,254,255
The service manual is here: http://www.nodevice.com/manual/newmans/hitachi/c15fb_service_manualpdf/get32740.html
Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.
Related Hitachi c15fb Manual Pages
User Manual - Page 1
...The circled numbers in the descriptions below correspond to the item numbers in the Parts List and exploded assembly diagram. [CAUTION] Prior to lose the D12.7 Steel Ball [117] and Sprint (C) [118].
--- 1... commencing disassembly (including replacement of the saw blade), ensure that the
plug is disconnected from the rear portion of the Base and Turn Table:
Tools Required:
• 17 mm Box ...
User Manual - Page 2
... [97] and Grip [100]) and slowly and carefully raise the Gear Case [53]. Machine Screws [15] and four D5 x 90 -Hd. Tapping Screws [13] it in the Set Pin [97] ... Flat Hd. Insert screwdriver through the holes at all times. (2) Disassembly of the Saw Cover Section: Tools Required:
• Plus Screwdriver
The Saw Cover Ass'y [3] can be disassembled by removing the M4 x 10 -Hd. Particular...
User Manual - Page 3
...] can then be disassembled, first loosen the two M5 x 20 -Hd. B. Screws [74], gently tap on the saw cover side of the Switch and Handle Section: Tools Required:
• Plus Screwdriver
A. Tapping Screws [21], the Switch [22] can be separated from the Stopper Pin [52], the Stopper Pin [52] and Gauge Spring [38] can...
User Manual - Page 4
... Caps [55] from the Switch [22]. Remove the Armature Ass'y [36] from the Housing Ass'y [84]. Disassembly of the Armature Ass'y and Stator Ass'y: Tools Required:
• Plus Screwdriver..., Nippers, Wooden or Plastic Hammer
1. Tapping Screws [41], and remove the Tail Cover [42] from the Housing Ass'y [84].
2. Loosen the two M5 x 75 -Hd. Remove the Saw...
User Manual - Page 5
..., the Gear Case may move and vibrate on the Hinge Shaft are tightened excessively, it may interfere with the main switch turned ON. Assemblies Requiring Careful Adjustment: (1) Perpendicularity Adjustment of the Saw Blade (or Dummy Disc) and Vise (B):
If the Hinge is disassembled from and then reassembled to the polycarbonate portion of...
User Manual - Page 6
...of Appropriate Insulation: When making leadwire connections, do not remove any more of the Switch. A. Details concerning adjustment
Vise (B)
procedures are listed in accordance with the M10 x...Saw Blade, and perform adjustment with cutting
needs.
1-4. study them carefully, and set the Turn Table [87] to set the Saw Blade at the most appropriate height (H) above adjustment, lower the Saw...
User Manual - Page 7
Wiring Diagrams and Leadwire Arrangements: Perform wiring work as illustrated below. (1) For Products with a Dynamic Brake (115V Specification Products for the U.S. and Canada Only):
WIRING DIAGRAM
Armature Ass'y
Stator Ass'y
Switch Black
Brown
White
White Connector
Cord
LEADWIRE ARRANGEMENT
Noise Suppressor Connector
Switch
Tube (A)
Cord Cord Armor
--- 7 --- 1-5.
User Manual - Page 8
(2) For Products with a Noise Suppressor: [NOTE] The wiring diagram for products without a Noise Suppressor is the same as that illustrated below with the
exception of the Noise Suppressor section.
WIRING DIAGRAM
Armature Ass'y
Stator Ass'y
LEADWIRE ARRANGEMENT
Noise Suppressor
Switch
Vinyl Tube
Black Red
Black
Red
Green
Terminal (w/o insulation tube)
M5 x 75 Machine Screw...
User Manual - Page 9
...Saw Blade, and subsequent
Lock Nut [92] to the item numbers in the Parts List and exploded
assembly diagram...bevel cutting, resulting in inaccurate angles.
Excessive deflection of the workpiece. Excessively fast cutting operation speed causes deflection of cut into Workpiece at inclined angle.
0.2/190 (Fig. 1)
• Adjust M12 Nut [93] and M12
Lock Nut [92] to cut surface.) (Mitered...
User Manual - Page 10
...Saw Blade. (Inherent Saw Blade deflection will cause rough surfaces.)
0.26/φ 370
Replace the Saw Blade. (To obtain very fine cutting surfaces, Hitachi's TCT Saw Blade for a
100 mm (4") workpiece is 10 --- 15....
---- piece to cut surface.) (Mitered joints cannot be accurately aligned.)
2.
The workpiece is recommended.)
B. Cut with a TCT Saw Blade for
wood or aluminum (code ...
User Manual - Page 11
... [116] without fail to fix the
Turn Table in Item 1. Repair or adjust affected parts as described in position. (The Ball
Index Settings at 0˚, 15˚, 22.5˚,
30˚ and 45˚ are affected by
vibration, and are not sufficient to remove defects, and recheck the cutting. Plane the...
Similar Questions
Wiring Diagram For Hitachi Miter Saw
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
I bought a switch for Hitachi c10 fc2 & need a wiring diagram to hook it upThank You Dave
(Posted by delliott49 7 years ago)
Controller
can i bypass controller by rewiring since you can not get item
can i bypass controller by rewiring since you can not get item
(Posted by workmastersinc 7 years ago)
How Can I Fix New Switch Trigger On My Dh24pc3
(Posted by petarnevenov 11 years ago)
Need Additional Specs For The Hitachi 15' C15fb
Will it cut 6-5/8" schedule 40 black plastic pipe? What is the measurement from the bottom of the b...
Will it cut 6-5/8" schedule 40 black plastic pipe? What is the measurement from the bottom of the b...
(Posted by toolgirl 12 years ago)
Hitachi C15fb Miter Saw
How do I remove the hinge shaft to replpace the springe? It looks like it can be forced out.
How do I remove the hinge shaft to replpace the springe? It looks like it can be forced out.
(Posted by edmahoney 12 years ago)