Hitachi NT65GS Support Question
Hitachi NT65GS Support Question
Find answers below for this question about Hitachi NT65GS - 2-1-2" 16 Gauge Gas Powered Straight Finish Nailer.Need a Hitachi NT65GS manual? We have 2 online manuals for this item!
Question posted by Jordanmcmahon007 on May 18th, 2021
Trouble Shooting
I'm wondering if anyone can give me help with my gun. It won't press down all the way anymore to alow the motors come on to fire a Nail. It was working fine on a job then just stopped. I swapped gas bottles and battery's and still the same issue
Current Answers
Answer #1: Posted by techyagent on May 18th, 2021 1:22 PM
techyagent
Member since:
June 17th, 2014 Points: 4,799,790
Member since:
June 17th, 2014 Points: 4,799,790
Techygirl
Answer #2: Posted by hzplj9 on May 18th, 2021 1:24 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,510
Member since:
June 25th, 2012 Points: 4,873,510
Check if there is a nail stuck in the drive mechanism. This will cause a jam. Some dismantling may be required. Remove the stack of nails from the unit and then check.
This is a guide from Manualslib.com if you do not have one to hand. Page 32 onwards explains the maintenance of the product.
Hope that helps.
Related Hitachi NT65GS Manual Pages
Instruction Manual - Page 4
EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER
⅜ This tool has a FULL SEQUENTIAL ACTUATION MECHANISM. Follow the same sequence to drive the nail. WARNING indicates a potentially hazardous situation which, if not avoided, could result in DEATH or SERIOUS INJURY. Never use this Nailer for applications other than those specified in this nailer.
First, press the push...
Instruction Manual - Page 5
... flammable liquids or gases, e.g. English
SAFETY
IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS
READ ALL INSTRUCTIONS
This Nailer is powered by the Nailer operator and others in this instruction manual. This Nailer produces hot exhaust gases that may flammable materials. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Do not touch with...
Instruction Manual - Page 6
... - Do not incinerate, refill, reclaim or recycle the fuel cell.
NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. This Nailer shall not be used in horseplay with the Nailer. The device may fail to follow instructions may burst, releasing flammable gas. Failure to operate below
32°F (0°C) or above 104°F (40...
Instruction Manual - Page 7
...work areas of entry.
18. the fasteners can ricochet and hurt someone .
20. The fasteners can be store in tool case and
in low temperatures and drive operations may be driven into the Nailer...NAILER PROPERLY WITH FUEL
CELL AND BATTERY REMOVED. Do not tamper with the device facing upward and press...handle the Nailer. Rubber gloves and nonskid footwear are missing or damaged.
16. DRESS ...
Instruction Manual - Page 8
... and inspection; 2) clearing a jam; 3) it is not in use; 4) leaving work area; 5) moving it immediately and arrange for better and safer performance.
30. English
SAFETY - MANUAL.
23. USE ONLY PARTS, ACCESSORIES OR
FASTENERS
SUPPLIED
OR
RECOMMENDED BY HITACHI. If the Nailer appears to malfunction and resulting
injuries. STAY ALERT. TAKE FUEL CELL...
Instruction Manual - Page 9
... a skin cream when dry. rinse the open the fuel cell.
Do not dispose of the tool and disposal. wash the contact surface carefully with skin ; Store in fire and explosion when handling dispensers for combustible gas for the purpose of storage, transportation, inserting into and taking out of fuel cell with other...
Instruction Manual - Page 10
... and (3) product using the battery charger.
10 Use of the HITACHI battery operated tools before attempting any way; take it will not reduce this case, please confirm Instruction Manual of improper extension ... (7.5) 50 (15) 100 (30) 150 (45)
0
2 18 18 18 16
2
3 18 18 16 14
3
4 18 18 16 14
* If the input rating of injury, charge HITACHI rechargeable battery type EBM315. To...
Instruction Manual - Page 13
NAME OF PARTS
1. Gas Finish Nailer
Top cover
Actuator
Chamber
Handle
Top cover
Chamber
Actuator Handle Battery
Piston
Driver blade
Trigger
Battery Hook
Piston
Driver blade
Trigger
Firing head
(outlet)
Magazine
Push lever Nail feeder (B)
Top cover
Chamber
Actuator Handle
Magazine
Firing head (outlet)
Nail feeder (B)
Push lever
⅜ Battery (EMB315)
Terminal hole
...
Instruction Manual - Page 14
... hole
Connecting socket
Charger connecting plug
Pilot lamp
Nameplate (on the bottom side)
Charger connecting plug
Cigarette lighter connecting plug
Cord
14
AC adapter
Cord Gas Brad Nailer
Top cover
Chamber
Piston Driver blade
Actuator Handle
Battery
Trigger
Hook Stop lever
Firing head
(outlet)
Push lever
Magazine
Magazine cover
3.
Instruction Manual - Page 15
... 1.5 A 0.4 lbs (0.2 kg)
NOTE: The charging time may vary according to temperature and power source voltage.
15 English
SPECIFICATIONS
1. Gas Finish Nailer
Model Dimensions
Length × Height × Width Weight Includes battery and fuel cell Nail capacity
Cycle rate
Battery Fuel Cell
NT65GS
NT65GB
NT65GA
10-1/4" × 11" × 3-3/8"
10-5/8" × 11-1/8" × 3-3/8"
12" ×...
Instruction Manual - Page 16
... for the NT65GS, NT65GB, NT65GA or the NT50GS. Dimensions of any other nails can result in the Table below can be driven with this Nailer. Only nails shown in tool malfunction and/or nail breakdown, leading to use of nails
16 Gauge finish nails (straight)
Min. .110" (2.8mm)
Max.
2-1/2" (65mm)
1" (25mm) .051" (1.3mm)
.055" (1.4mm)
.065" (1.65mm)
16 Gauge finish nails (Angle: 20...
Instruction Manual - Page 21
...work.
⅜ If the Nailer, fuel cell and battery are already cold, bring it in a cold weather environment.
Do
not contact with the new metering valve.
Replace with
gases.
ⅷ Do not inhale.
ⅷ Keep out of reach
of fuel
cell away from the gas...FOR FUEL CELL" (page 9). English
WORKING ENVIRONMENT
WARNING
ⅷ No flammable
gas, liquid or other
flammable objects
at ...
Instruction Manual - Page 22
... when the remaining number of nails becomes less than 6 or 9.
(3) Press downward on fuel cell two or three times against a stationary object and release.
The fuel cell is flashing red, the battery doesn't have enough power and it . You must charge the battery before use Nailer unless push lever is flashing green. The charging...
Instruction Manual - Page 31
...Nailer.
Lubricate it with Hitachi Gas tool lubricant. DANGER
ⅷ Never use ,
(50°C)
the Nailer, fuel
cell and battery
should be driven at
temperature
below 120°F
(50°C).
31 and 2) clearing a jam.
1. DANGER
ⅷ Store Nailer..., battery and all nails from those on your own Nailer.
Cloth
CAUTION
ⅷ Check that differ from Nailer when: 1) doing ...
Instruction Manual - Page 105
NT65GS
ITEM NO. SOCKET HD. SHOULDER BOLT M4×32
1
52 CYLINDER
1
53 CHAMBER STOP...16
92 RIBBON SPRING
93 NAIL FEEDER (B)
94 PRISM
95 CONTROLLER
96 TAPPING SCREW (W/FLANGE) D4×12
97 NAIL RAIL
98 PUSHING SPRING
99 NAIL.... BOLT M4×16
4
14 CHAMBER HEAD
1
15 GASKET
1
16 CHAMBER
1
17 PISTON RING (B)
4
18 RETAINING RING FOR D40 HOLE
1
19A MOTOR ASS'Y
1
20 ...
Instruction Manual - Page 107
...16
14 CHAMBER HEAD
15 GASKET
16 CHAMBER
17 PISTON RING (B)
18 RETAINING RING FOR D40 HOLE
19 PACKING
20 ADAPTER
21 HEX. SHOULDER BOLT M4×32
42 CYLINDER
43 CHAMBER STOP... COVER
24 HEX.SHOULDER BOLT M5
25 MOTOR ASS'Y
26 PISTON RING (A)
27 PISTON
28 PISTON BUMPER... SCREW M4
89 ROLL PIN D3×16
90 RIBBON SPRING
91 NAIL FEEDER (B)
92 NAIL FEEDER (A)
93 PUSHING SPRING
94 ROLL ...
Instruction Manual - Page 109
... 1 1 1 1 1 1 1 2 1 1 1 1 1 1
109 SHOULDER BOLT M4×32
1
42 CYLINDER
1
43 CHAMBER STOP RUBBER
1
44 NYLON NUT M5
3
45 HITACHI PLATE
1
46 SEAL LOCK HEX. BOLT M4×10
75 TRIGGER STOPPER
76 PIN D3×...16
90 RIBBON SPRING
91 NAIL FEEDER (B)
92 NAIL FEEDER (A)
93 STOPPER SPRING (C)
94 PRISM
95 CONTROLLER
96 TAPPING SCREW (W/FLANGE) D4×12
97 NAIL...
2
25A MOTOR ASS'Y
...
Instruction Manual - Page 111
...
1
96 PRISM
1
97 NAIL FEEDER
1
98 NAIL PLATE
1
99 FEEDER PIECE
1
100 FEED SPRING
1
101 CYLINDER ASS'Y (A)
1
102 CYLINDER HEAD ASS'Y
1
501 CHARGER (UC3SML)
1
502 SAFETY GLASSES
1
503 HEX. SOCKET HD. BOLT M4×16
4
14 CHAMBER HEAD
1
15 GASKET
1
16 CHAMBER
1
17 PISTON RING (B)
4
18 RETAINING RING FOR D30 HOLE
1
19 MOTOR ASS'Y
1
20...
Instruction Manual - Page 112
au 1-800-59-TOOLS (appel gratuit), ou UN SERVICE APRÈS-VENTE D'OUTILS ÉLECTRIQUE AGRÉÉ ...Ltd.
3950 Steve Reynolds Blvd.
Pour le RAMASSAGE, contacter HITACHI KOKI U.S.A. número 1-800-59-TOOLS (llamada gratis), o con HITACHI AUTHORIZED POWER TOOL SERVICE CENTER. Norcross, GA 30093
Hitachi Koki Canada Co.
450 Export Blvd.
Unit B, Mississauga ON L5T 2A4
811 Code No...
Parts List - Page 2
...-347 HEX. BOLT M4X16 (10 PCS.)
4
14 886-295 CHAMBER HEAD
1
15 886-296 GASKET
1
16 886-297 CHAMBER
1
17 886-312 PISTON RING (B)
4
18 886-298 RETAINING RING FOR D40 HOLE
1
19A 886-662 MOTOR ASS'Y
1 INCLUD. 22, 23
20 886-315 PACKING
1
21 886-313 ADAPTER
1
22 886-314 HEX...
Similar Questions
Screeching Noise
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
(Posted by Rongowrie 2 years ago)
Nail Gun Won’t Work
my nail gun stopped working after using it twice,I opened back up and a fan is loose,is this the pro...
my nail gun stopped working after using it twice,I opened back up and a fan is loose,is this the pro...
(Posted by Iandharkness 5 years ago)
Nt65ga Will Not Fire
NT65GA Does not fire when trigger is pulled. Battery has full charge.
NT65GA Does not fire when trigger is pulled. Battery has full charge.
(Posted by dmcgeeoo6 7 years ago)
Pin Keeps Popping Out
the pin in the gun keeps popping out. if i flip open the top and push the pin back in it pops again ...
the pin in the gun keeps popping out. if i flip open the top and push the pin back in it pops again ...
(Posted by xpertcarpentry 11 years ago)
Stopped Firing Nails
I was shooting nails and it just stopped firing. There is no nail in the gun, no jam and the fuel ce...
I was shooting nails and it just stopped firing. There is no nail in the gun, no jam and the fuel ce...
(Posted by Blest444 12 years ago)