Hitachi NT65GS Support Question
Hitachi NT65GS Support Question
Find answers below for this question about Hitachi NT65GS - 2-1-2" 16 Gauge Gas Powered Straight Finish Nailer.Need a Hitachi NT65GS manual? We have 2 online manuals for this item!
Question posted by info35719 on July 6th, 2014
Fan Has Broken Of The Shaft Inside Nt65gs Hitachi Need Part With Threaded Shaft
looks like the fan was screwed to the shaft. the shaft was threaded but has snapped and the fan has come away with the thread still in it. The shaft runs into a body which may be a motor that turns the shaft. black and red wires coming out of the top. Can i get some advice on buying the new part required please.
Current Answers
Answer #1: Posted by freginold on July 7th, 2014 3:05 AM
freginold
Member since:
December 20th, 2011 Points: 23,252,885
Member since:
December 20th, 2011 Points: 23,252,885
Hi, here is the parts list for the NT65GS:
http://www.toolpartspro.com/image/NT65GS/NT65GS-hitachi-PB.pdf
It looks like the piece you're talking about is #19A in the diagram, the motor assembly with shaft, part# 886-662. ToolPartsPro.com sells it for $86.81.
http://www.toolpartspro.com/image/NT65GS/NT65GS-hitachi-PB.pdf
It looks like the piece you're talking about is #19A in the diagram, the motor assembly with shaft, part# 886-662. ToolPartsPro.com sells it for $86.81.
Related Hitachi NT65GS Manual Pages
Instruction Manual - Page 4
...
DANGER indicates an imminently hazardous situation which , if not avoided, could result in DEATH or SERIOUS INJURY. EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER
⅜ This tool has a FULL SEQUENTIAL ACTUATION MECHANISM. First, press the push lever against the workpiece;
Failure to observe basic safety rules or precautions. English
IMPORTANT INFORMATION...
Instruction Manual - Page 8
... OVERREACH.
27. and 6) handing it immediately and arrange for better and safer performance.
30. USE ONLY PARTS, ACCESSORIES OR
FASTENERS
SUPPLIED
OR
RECOMMENDED BY HITACHI. The Nailer should never be hidden by you if you are under the influence of alcohol, drugs or medication that may be left unattended since people who...
Instruction Manual - Page 10
...16 14
3
4 18 18 16 14
* If the input rating of fire, electric shock, or injury to persons.
6.
Table 1 RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes* AWG Size of the HITACHI battery operated tools...and electric shock. Do not operate battery charger if it to HITACHI battery operated tools as those of electric shock or fire.
12. take it ...
Instruction Manual - Page 11
...CHARGER WITH
A DC 12V IN-CAR POWER
SOURCE
1. Do not use the Nailer. If you use the battery charger other...USE ONLY HITACHI BATTERY TYPE EBM315. NEVER 7. incinerate the battery, even if it , the battery and in -car power source.
English.... Electric shock or damage to the car body.
2. charge outdoors. Keep the battery away from driving. charge when the temperature is completely...
Instruction Manual - Page 13
... illustrations in this Manual is designed to assist you in this Manual may show details or attachments that differ from those on your own Nailer. Gas Finish Nailer
Top cover
Actuator
Chamber
Handle
Top cover
Chamber
Actuator Handle Battery
Piston
Driver blade
Trigger
Battery Hook
Piston
Driver blade
Trigger
Firing head
(outlet)
Magazine
...
Instruction Manual - Page 15
... 1.5 A 0.4 lbs (0.2 kg)
NOTE: The charging time may vary according to temperature and power source voltage.
15 English
SPECIFICATIONS
1. Gas Finish Nailer
Model Dimensions
Length × Height × Width Weight Includes battery and fuel cell Nail capacity
Cycle rate
Battery Fuel Cell
NT65GS
NT65GB
NT65GA
10-1/4" × 11" × 3-3/8"
10-5/8" × 11-1/8" × 3-3/8"
12" ×...
Instruction Manual - Page 16
..." (1.4mm)
.065" (1.65mm)
16 Gauge finish nails (Angle: 20°)
Min. .110" (2.8mm)
Max.
2-1/2" (65mm)
1-1/4" (32mm) .051" (1.3mm)
.055" (1.4mm)
.065" (1.65mm)
16
Dimensions of any other nails can be driven with this Nailer. English
NAIL SELECTION
WARNING
ⅷ Be sure to serious injuries. The use only the genuine HITACHI nails for the NT65GS, NT65GB, NT65GA or...
Instruction Manual - Page 18
...finishing process for M5 screw 1 8 Nose cap (mounted on tool)
(except NT50GS 1 9 Nose cap (mounted on tool)
(only NT50GS 1 0 Case 1
CHARGING METHOD
NOTE: Before plugging into the receptacle, make sure the following points. ⅜ The power source voltage is stated on the part of HITACHI...
986) ⅜ Degreaser/cleaner (Code No. 728-985)
NOTE: Accessories are subject to the power source.
Instruction Manual - Page 19
Insert the battery to contact your HITACHI AUTHORIZED SERVICE CENTER.
⅜ Regarding the temperature of the socket may result in the table ...charger in the car. NOTE: The battery charging time becomes longer when a temperature is low or the voltage of the power source is loose and falls out of the cigarette lighter socket, repair the socket.
4. Secure the battery charger in place...
Instruction Manual - Page 22
... occurs, stop using the Nailer and contact a Hitachi authorized service center immediately.
(1) REMOVE ALL NAILS, FUEL CELL AND BATTERY FROM NAILER.
Ⅺ ALL SCREWS MUST BE TIGHTENED.
Ⅺ...Nailer unless push lever is operating properly.
22
Push lever
Nail feeder (B)
(2) Installing the battery. Make sure the battery indicator light is flashing red, the battery doesn't have enough power...
Instruction Manual - Page 24
... nails into the back of the
magazine. Magazine
(2) Slide the nail strip forward in the Nailer. Pull trigger
(6) Without touching the trigger, depress the push lever against the workpiece with pulling...magazine. Drive nails into the workpiece that position for 5 seconds or longer.
Ⅺ THE NAILER MUST NOT OPERATE. Depress push lever
Nail feeder (B)
(5) Separate the push lever from the...
Instruction Manual - Page 27
... fastener will be driven into and through or away from workpiece and hit someone .
ⅷ Do...Nailer at the temperature below 32°F (0°C). ⅷ Using the tool for unloaded operation. next, pull the trigger to oil around the exhaust outlet or nose, resulting in spattering.
Have it repaired immediately.
ⅷ Never place your face, hands or feet closer than 6 or 9. NT65GS...
Instruction Manual - Page 30
English 3 Release the lock lever and open guide
plate. Lock lever
3 Guide Plate 4 Remove the jammed nail with a slottedhead screwdriver.
5 Close guide plate and latch. NOTE: ⅷ In case of frequent jam, contact a Hitachi
authorized service center.
30
Instruction Manual - Page 32
...Hitachi, distributor or employer shall repair the Nailer.
ⅷ Use only parts supplied or recommended by a Hitachi Authorized Service Center. All quality Nailers will be carried out by Hitachi for an extended period, apply a thin coat of Hitachi Power Tools... type and ratings of fire, replace only with
loosened screws is available from normal use for repair. WARNING LABEL ...
Instruction Manual - Page 34
...piston. Exchange it doesn't drive a nail
or operation unstable. English
PROBLEM
CHECK METHOD
Fan is pressed.
Unable to charge battery.
---------- Too low temperature, warm up fuel cell...Fan does not operate when push lever is working, light
Check for replacement.
Load more nails in the magazine. Contact Hitachi for returning of the light indicator. If green: Contact Hitachi...
Instruction Manual - Page 105
...HITACHI PLATE
1
ITEM NO. SCREW M4
70 HANDLE (A)
71 TERMINAL SUPPORT
72 TRIGGER STOPPER
73 TRIGGER
74 TRIGGER SPRING
75 CORD COVER PLATE
76 CHAMBER SPRING
77 HEX.
BAR WRENCH 4MM
504 HEX. BOLT M4×16
4
14 CHAMBER HEAD
1
15 GASKET
1
16 CHAMBER
1
17 PISTON RING (B)
4
18 RETAINING RING FOR D40 HOLE
1
19A MOTOR... SCREW M4×5
2
23 SHAFT RUBBER WASHER
1
24A SHAFT ...
Instruction Manual - Page 107
...6 NYLOCK BOLT M4×12
7 CYLINDER HEAD
8 NUT M3
9 SPRING WASHER M3
10 WASHER M3
11 FAN
12 RUBBER PLATE
13 HEX. BOLT M4×10
74 PUSH LEVER ARM
75 PUSH LEVER PIECE
76 O-RING ...SCREW M4×5
22 SHAFT RUBBER WASHER
23 SHAFT COVER
24 HEX.SHOULDER BOLT M5
25 MOTOR ASS'Y
26 PISTON RING (A)
27 PISTON
28 PISTON BUMPER
29 NAME PLATE
30 HOUSING
31 GUIDE PIN
32 ROLL PIN D3×16...
Instruction Manual - Page 109
...
1
36 LOCK LEVER
1
37 ROLL PIN D3×16
1
38 GUIDE PLATE
1
39 TAPPING SCREW (W/FLANGE) D4×16
2
40 HANDLE (B)
1
41 HEX. BAR WRENCH 3MM
504 HEX. SOCKET HD. SOCKET SET SCREW M4×5
2
22 SHAFT RUBBER WASHER
1
23A SHAFT COVER
1
24 HEX.SHOULDER BOLT M5
2
25A MOTOR ASS'Y
1
26 PISTON RING (A)
2
27 PISTON
1
28 PISTON...
Instruction Manual - Page 111
SOCKET HD. SOCKET SET SCREW M4×5
2
24 SHAFT RUBBER WASHER
1
25 SHAFT COVER
1
26 PISTON RING (A)
2
27 PISTON
1
28 PISTON BUMPER
1
29 NAME PLATE
1
30 HOUSING
1
31 PIN
1
32 BLADE GUIDE
1
33 SEAL LOCK HEX. SHOULDER BOLT M4×32
1
52 CYLINDER
1
53 CHAMBER STOP RUBBER
1
54 NYLON NUT M5
1
55 HITACHI PLATE
1
ITEM...
Parts List - Page 2
...
3 886-347 HEX. SOCKET HD. SOCKET SET SCREW M4X5
2
23 886-567 SHAFT RUBBER WASHER
1
24A 886-663 SHAFT COVER
1
25 886-286 PISTON RING (A)
2... 886-296 GASKET
1
16 886-297 CHAMBER
1
17 886-312 PISTON RING (B)
4
18 886-298 RETAINING RING FOR D40 HOLE
1
19A 886-662 MOTOR ASS'Y
1 INCLUD.... (10 PCS.)
2
11 886-309 FAN
1
12 886-568 RUBBER PLATE
1
13 949-754 HEX. SHOULDER BOLT M5
2
41 ...
Similar Questions
Screeching Noise
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
nail gun gives screeching noise when firing nails sounds like fan motor but not sure when activated ...
(Posted by Rongowrie 2 years ago)
Hitachi Nt65gs
hi wondering if anybody has any information on how to strip down and rebuild the hitachi pin gun or ...
hi wondering if anybody has any information on how to strip down and rebuild the hitachi pin gun or ...
(Posted by sedgiejunior 3 years ago)
Nt65ga Will Not Fire
NT65GA Does not fire when trigger is pulled. Battery has full charge.
NT65GA Does not fire when trigger is pulled. Battery has full charge.
(Posted by dmcgeeoo6 6 years ago)
New Hitachi Nt65gs
first time using the nailer with 16ga nails, it starts firing two at a time. i dont want to use it u...
first time using the nailer with 16ga nails, it starts firing two at a time. i dont want to use it u...
(Posted by log07012746 10 years ago)