Hitachi M12VC Support Question
Hitachi M12VC Support Question
Find answers below for this question about Hitachi M12VC - 2-1/4 Peak HP Variable Speed Fixed Base Router.Need a Hitachi M12VC manual? We have 2 online manuals for this item!
Question posted by dhruvchanna on May 11th, 2014
Red Light Blinking Continuously 3 Star 1.5 Ton Window Ac Of Hitachi Since Night
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hitachi M12VC Manual Pages
Instruction Manual - Page 3
...to observe basic safety rules or precautions.
NEVER use this power tool in a manner that result from power tool operation and maintenance are caused by the failure to prevent bodily ... safety precautions are identified by HITACHI. Most accidents that has not been specifically recommended by WARNINGS on the power tool and in this power tool. English
IMPORTANT SAFETY INFORMATION
Read...
Instruction Manual - Page 4
...is an increased risk of fumes. (3) Keep bystanders children, and visitors away while operating a power tool. Work Area (1) Keep your hair, clothing and gloves away from heat, oil, sharp edges or ...rated for outdoor use an outdoor extension cord marked "WA" or "W". Water entering a power tool will increase the risk of electric shock.
3. Replace damaged cords immediately. Keep your work area ...
Instruction Manual - Page 5
... in unexpected situations.
(6) Use safety equipment. ALWAYS wear ear protectors when using . SPECIFIC SAFETY RULES AND SYMBOLS
1. Always wear eye protection. Any tool that are caused by poorly maintained tools. (8) Use only accessories that cannot be suitable for extended periods. Accessories that is dangerous and must be repaired. (4) Disconnect the plug form...
Instruction Manual - Page 6
... wait for cracks or damage before removing the
tool from these exposures varies, depending on . 9. Never run for symbols used on this type of the router bases. Definitions for a while. Your risk from ...immediately after operation: it is turned on how often you do this tool V volts Hz .......... hertz A amperes
no load speed
---/min ... To reduce your skin. 14. Always lead the ...
Instruction Manual - Page 7
Table shows the correct size to use this tool with a damaged or
frayed electrical cord or extension cord. Never use ...12
Not Recommended
WARNING: Avoid electrical shock hazard.
SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
7 An undersized cord will draw. The smaller the gage number, the heavier the cord.
Ampere Rating
More Not More
Than...
Instruction Manual - Page 8
... contained in the safe operation and maintenance of the power tool. NAME OF PARTS
Motor Housing
Dial
Switch
Brush Cap
Handle Lever
7/8 3/4 5/8
1/2 3/8 1/4
Scale Ring Base
Collet Chuck
Sub Base
SPECIFICATIONS
Model Motor Power source Collet chuck capacity Current No-load speed Weight (with cord)
Fig. 1
M12VC
M12SC
Single Phase, Series Commutator Motor
Single Phase 120V...
Instruction Manual - Page 9
... switch is in the OFF position. Extension cord When the work site is used, it may cause overheating, resulting in the ON position, the power tool will start operating immediately and can cause serious injury.
3. Contact a licensed electrician to the power source requirements specified on grooving and beveling.
WARNING:
Damaged cord...
Instruction Manual - Page 10
...shank bit which is provided as
follows. (a) Open the lever. (Fig. 2) (b) While holding the base, turn the motor
housing counterclockwise. (c) Turn it out approximately 1/16" (approx. 2 mm). (3) With...(viewed from under the router). (Fig. 3) (4) When using the 1/4" diameter shank bit, replace the equipped collet chuck with the one for installing bits in the base is firmly tightened after ...
Instruction Manual - Page 11
... The motor housing can be able to move the motor in the base when
the lever is clamped. HOW TO USE THE ROUTER
WARNING: Be sure to switch power OFF and disconnect the plug from...Base
Groove Lever
CAUTION:
Fig. 4
You should not be temporarily secured by clamping the lever (the motor housing does not slide down , make adjustments by its own weight). Adjusting depth of cut (1) Place the tool...
Instruction Manual - Page 12
... in place with the lock nut. English
(4) While holding up the base slightly, turn the motor housing clockwise until the index line on the motor... for minimum speed and position "6" for producing a large quantitiy of plywood or thin lumber. Guiding the router (1) Template guide (M12VC, M12SC: Optional
accessory) Use the template guide when employing a template for maximum speed. 3. Dial...
Instruction Manual - Page 13
...router along the materials side. 1 Insert the guide bar into the hole in the bar holder, then lightly tighten the 2 wing bolts (A) on top of the bar holder. 2 Insert the guide bar into the hole in the base... and wait until the bit attains full speed. Feed the router in the manner that the template guide moves...eye protection when operating this tool. ⅷ Keep your hands, face and other ...
Instruction Manual - Page 14
...16. This will look as well as the power source.
Router feed Router feed
workpiece Rotation of bit
Fig. 16
NOTE: ⅷ Moving the tool forward fast may cause a poor quality of cut on the...It may burn and mar the cut. Before beginning the cut on the base). Moving the tool forward too slowly may cause the rotation speed to fluctuate. ⅷ When using the straight guide, be sure to ...
Instruction Manual - Page 15
...router with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. The carbon brushes can then be performed by a Hitachi Authorized Service Center. Service and repairs All quality power tools... List will eventually require servicing or replacement of parts because of Hitachi Power Tools must be helpful if presented with loosened screws is worn in ...
Instruction Manual - Page 16
... 6. Accordingly, some parts (i.e. C: No. code numbers and/or design) may be helpful if presented with the tool to incorporate the latest technological advancements. In the operation and maintenance of Hitachi Power Tools must be carried
out by an Hitachi Authorized Service Center. B: Code No. This Parts List will be changed without prior notice.
16
Instruction Manual - Page 17
...M12VC, M12SC (1) 1/4" Collet Chuck (Code No. 323-293) (2) Template Guide Adapter (attaches
to
the router) (Code No. 323-272) (3) Centering Gauge (Code No. 323-296) (4) 16 mm Wrench (Code No. 323-294) (5) 23 mm Wrench (Code No. 323-295) (6) Large Hole Sub Base...or mechanical damage. The use with your tool.
Contact HITACHI if you are not intended for use of any obligation on the part of the...
Instruction Manual - Page 18
English
OPTIONAL ACCESSORIES sold separately
(1) Straight Guide Set (Code No. 323-342) 1Bar Holder (Code No. 323-343) 2Feed Screw (Code No. 956-793) 3Wing Bolt (Code No. 301-806) 4Guide Bar (Code No. 323-345) 5Straight Guide (Code No. 323-344) 2 3 1 4 5
(2) Dust Collector Set (Code No. 323-346)
NOTE: Specifications are subject to change without any obligation on the part of the HITACHI.
18
Similar Questions
My Hitachi Split Ac 6years Old Red Light 7 Times Blinking Kindly Help Any One
(Posted by rameshchithirai651 3 years ago)
Blinking Of Red Led
My ac was not working and started blinking led. For 7 times
My ac was not working and started blinking led. For 7 times
(Posted by ashrafkhan94069 4 years ago)
Works Once And Quits
I put a new battery in my NT 65GB it fires one nail then red light comes on then after a few seconds...
I put a new battery in my NT 65GB it fires one nail then red light comes on then after a few seconds...
(Posted by gnorth 6 years ago)
Red And Blue 3d Like Ghost Effect
My tv picture state displaying a red and blue 3D like ghost effect. The auto magic focus is not help...
My tv picture state displaying a red and blue 3D like ghost effect. The auto magic focus is not help...
(Posted by rodeocowgurl21 8 years ago)
My Hitachi Ac's Is Not Working. Red Led Is Blinking 7 Times. What's The Problem?
(Posted by arunamozhi 9 years ago)