Hayward Salt & Swim® 3C Support Question
Hayward Salt & Swim® 3C Support Question
Find answers below for this question about Hayward Salt & Swim® 3C.Need a Hayward Salt & Swim® 3C manual? We have 3 online manuals for this item!
Question posted by tnordcv on May 13th, 2017
Sas Chlorine Generator
The power has shut down on my generator, what could be the causes
Current Answers
Answer #1: Posted by BusterDoogen on May 13th, 2017 2:08 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,447
Member since:
October 30th, 2011 Points: 28,565,447
1. Depending on current conditions, there should always be at least one LED illuminated when the Salt & Swim 3C is powered. If no LEDs are on, check to make sure that the linecord is plugged in and that the GFCI outlet is powered. If no power is detected, the GFCI may have to be reset.
2. STANDING BY LED blinking The Salt & Swim 3C has shut down because the temperature of the pool/spa water is too high (120ºF) or too low (50ºF). The system will not resume operation until the water temperature returns to normal. Note: This condition can sometimes happen if the pool/spa temperature is already high and the heater is running. The temperature coming out of the heater and into the Cell could possibly be high enough to shut down the Salt & Swim 3C.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Hayward Salt & Swim® 3C Manual Pages
Salt & Swim 3C Owner's Manual - Page 1
092511 RevA
Salt & SwimTM 3C
Chlorine Generator for Inground Swimming Pools up to 30,000 gallons
Owner's Manual
Contents
Introduction 1 Installation 2 Operation 12 Troubleshooting........... 15 Warranty 21 Model: SAS
Hayward Pool Products 620 Division Street, Elizabeth NJ 07207
www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Salt & Swim 3C Owner's Manual - Page 3
... of a saline water purification system in a pool or spa using natural stone for coping or for pool sanitization. Introduction
Salt & SwimTM 3C is designed to produce 200lbs of 100% available chlorine over its lifetime. This unique low cost chlorine generator uses a replaceable electrolytic Cell (SAS-CELL) that the actual amount of most residential swimming pools up to bather load, rainfall...
Salt & Swim 3C Owner's Manual - Page 4
... Quick Start Guide and refer to page 8 of this installation.
Take care to the Salt & Swim 3C system. This must be done BEFORE activating the Salt & Swim 3C. Installation
Remove power to the pool filter pump before you intend to operate the Salt and Swim. The Control Box must be mounted a minimum of non-copper based algaecide to operating the...
Salt & Swim 3C Owner's Manual - Page 5
...Salt & Swim 3C Control Box
The Salt & Swim 3C is contained in a raintight enclosure that is mounted.
It must be mounted a minimum of 10 ft. (4 meters) horizontal distance (or more, if local codes
require) from the pool..., within 3ft from a GFCI outlet, and within 3 feet of the Control Box. Before securing the Control Box to the intended location, make sure that the power cord will...
Salt & Swim 3C Owner's Manual - Page 9
...pool water must be balanced and salt must be added to your pool water for Salt & Swim 3C operation. After the flow switch is installed. Follow the instructions below: 1. When finished, the Salt & Swim 3C will occur just once when a new Cell is initialized, the Salt & Swim 3C...been done, refer to 30 seconds. Keep the Salt & Swim 3C powered for information on your filter pump and begin ...
Salt & Swim 3C Owner's Manual - Page 10
...
CORROSIVE
SCALING
8
OK
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Saturation index
The saturation index (Si) relates to ensure maximum performance from your Salt & Swim 3C chlorine generator. Si = pH + Ti + Ci + Ai - 12.1
ºC
ºF
Ti
Calcuim Hardness
Ci
Total Alkalinity
Ai
12 ...the Si is an indicator of Pool and Spa Professionals (APSP). If the Si is above equation.
Salt & Swim 3C Owner's Manual - Page 11
...). Use the equations below (measurements are in the pool and add salt according to the chart on page 10. A high salt level can cause the Salt & Swim 3C to shutdown and may begin to be added to ... of the Salt & Swim 3C and result in low chlorine production. Salt Level
Use the chart on page 10 to determine how much stabilizer must be tasted at a level of the pool.
The salt in pounds or...
Salt & Swim 3C Owner's Manual - Page 14
... of normal operation to the Troubleshooting section in its expected life. To cancel super chlorinating, press the SUPER CHLORINATING button again.
12 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS When this manual. Refer to increase or decrease the chlorine generation. The pool filter pump could be introduced, press the SUPER CHL ORINATING button. Press ( + ) and ( - ) to...
Salt & Swim 3C Owner's Manual - Page 15
... have an ON/OFF switch . This is first applied to the Salt & Swim 3C, an initialization routine will illuminate.
For pools with 5 DAILY CHLORINE OUTPUT LEDs illuminated. Salt & Swim 3C stops generating when the pool water temperature drops below 50ºF. This is 50º - 60ºF. the DAILY CHLORINE OUTPUT setting 3. You may need to raise the setting when the...
Salt & Swim 3C Owner's Manual - Page 16
...usually the cause). If ...remove the Cell. Servicing and Cleaning the Salt & Swim 3C Cell
Unplug Salt & Swim 3C from the GFCI outlet and remove power from the pump, filter, and supply ... any freezing conditions occur. Most pools require less chlorine during cold weather: Check chlorine levels periodically.
Maintaining the Salt & Swim 3C System
The replaceable Cell uses the...
Salt & Swim 3C Owner's Manual - Page 17
...ºF causes Salt & Swim 3C to stop generating
- Salt level too high
- "Yellow Out" or similar treatment recently used. Some yellow algae treatments will use
chlorine at www.hayward.com. LEDs not on
Depending on Cell.
- If no obstructions or restrictions in and that the GFCI outlet is powered. Note: This condition can sometimes happen if the pool/spa temperature...
Salt & Swim 3C Owner's Manual - Page 23
...Salt & Swim 3C chlorination products to be the sole determinant of the date of installation of the product. WARRANTY EXCLUSIONS: 1.
For more information on pools... SAS-CELL - 1 year limited warranty
Hayward warrants all accessories and other replacement parts for the above-identified chlorination ...pool or spa, war or acts of purchase or the nearest Hayward authorized warranty service...
Salt & Swim Owner's Manual - Page 1
092513 RevA
Salt & SwimTM
Chlorine Generator for Inground Swimming Pools up to 30,000 gallons
Owner's Manual
Contents
Introduction 1 Installation 2-8 Operation 12-14 Troubleshooting........... 15 Warranty 21 Model: SAS-PRO
Hayward Pool Products 620 Division Street, Elizabeth NJ 07207
www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Salt & Swim Owner's Manual - Page 3
... and circumstances. Introduction
The Salt & SwimTM is an automatic chlorine generation system for use of a saline water purification system in a pool or spa using natural stone for coping or for inground swimming pools up to 30,000 gallons (114,000 liters). The Salt & Swim is NOT to bather load, rainfall, temperature, and the pool's cleanliness. This SAS-PRO model is designed...
Salt & Swim Owner's Manual - Page 10
...39 103 .9
800
2.5
800
2.9
How to the Chemistry Quick Start Guide information on testing and adjusting your Salt & Swim chlorine generator. Insert values of pH, Ti, Ci and Ai
into the water. If Si equals .2 or more, scaling.... Your water is properly balanced if the Si is an indicator of Pool and Spa Professionals (APSP). Saturation index
The saturation index (Si) relates to determine...
Salt & Swim Owner's Manual - Page 11
... a level of rain). A high salt level can cause the Salt & Swim to shutdown and may begin to give a salty taste to your pool is not lost due to the addition of water because of splashing, backwashing, or draining (because of about 3500-4000 ppm). The salt in low chlorine production. Brush the salt around to speed up the...
Salt & Swim Owner's Manual - Page 14
... when performing the Flow Switch Calibration procedure. This electronically "super chlorinates" (boosts chlorine generation output) the water for the filter pump to the Troubleshooting section... in its expected life. Illuminates when there is not the case, refer to turn on during this time). The pool...
Salt & Swim Owner's Manual - Page 15
... the "+" and "-" button on the Salt & Swim unit. Each DAILY CHLORINE OUTPUT LED represents 6 minutes of chlorine generation out of operation.
The unit is perfectly normal and does not require any input from the Salt & Swim unless pool components are illuminated, the Salt & Swim unit will be idle for approximately 30 seconds.
When power is usually not a problem because bacteria...
Salt & Swim Owner's Manual - Page 17
...;F causes Salt & Swim to illuminate. Cold water between 50ºF - 60ºF causes Salt & Swim to reduce output regardless of days before
the pool returns to "normal" and chlorine tests will show the operation status as well as alert the user to shut down because the temperature of Nitrogen in the pool
plumbing.
- High level of the pool/spa water is powered. LEDs...
Salt & Swim Owner's Manual - Page 23
...(effective 12/01/12) Hayward warrants its Salt & Swim chlorination products to be the sole determinant of the ...CHLORINATOR CELL OTHER THAN AN UNMODIFIED, NEW HAYWARD CHLORINATOR CELL PURCHASED FROM HAYWARD. Problems resulting from failure to a pool or spa... SAS-CELL - 1 year limited warranty
Hayward warrants all accessories and other replacement parts for the above-identified chlorination products...
Similar Questions
S&s 3c Powers Off
When I Power Chlorinator Up 3 Led's Light Up And Max Light Blinks Then The All Lights Power Off.
When I Power Chlorinator Up 3 Led's Light Up And Max Light Blinks Then The All Lights Power Off.
(Posted by DANANEVENS 1 year ago)
Why Does My Aqua Rite Chlorine Generator Read High Salt
(Posted by cibusman 10 years ago)
Salt And Swim 3c
The min light and 3-7 lights are lite up when we turn pump off the low flow light does not come on. ...
The min light and 3-7 lights are lite up when we turn pump off the low flow light does not come on. ...
(Posted by sonyamarvin 10 years ago)
Do You Also Support The Swimpure Plus Chlorine Generator?
Our SwimPure Plus chlorine generator is two years old and I just cleaned it with muriatic acid solut...
Our SwimPure Plus chlorine generator is two years old and I just cleaned it with muriatic acid solut...
(Posted by cand4jays 11 years ago)