Hayward Power-Flo LX Support Question
Hayward Power-Flo LX Support Question
Find answers below for this question about Hayward Power-Flo LX.Need a Hayward Power-Flo LX manual? We have 3 online manuals for this item!
Question posted by cyclemama17 on June 6th, 2017
Strainer Cap
hi. I have a cracked strainer cap on my pump. I need the part number so I can order online. My model # is sp-1510z1xbc. I really appreciate your help.
Current Answers
Answer #1: Posted by TheTWWW on June 6th, 2017 6:49 AM
TheTWWW
Member since:
May 22nd, 2017 Points: 37,200
Member since:
May 22nd, 2017 Points: 37,200
Hi Please click this link below
https://www.hayward-pool.com/pdf/manuals/PowerFlo-LX-II-EPPumpSeries.pdf
Related Hayward Power-Flo LX Manual Pages
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 1
...pool is protected by applicable electrical codes. Make sure suction joints are closely supervised at all suction and discharge lines and valves, as well as air bleed (if available) on suction lift and horizontal length of the motor. 4. Turn on power and allow a reasonable time for the mechanical shaft seal. If the pump... PRIMING INSTRUCTIONS
Fill strainer housing with a 3 ft. (1...
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 2
...1
PART NUMBER
MODEL SP-1575LXTL
MODEL SP-1580TL
MODEL SP-1580X15TL
SPX1500-N2
SPX1500-N2
SPX1500-N2
SPX1580-BP
SPX1580-BP
SPX1580-BP
SPX1580-Z-1
SPX1580-Z-1
SPX1580-Z-1
SPX1500-F
SPX1500-L
SPX1500-L
SPX1250-XZ-2
SPX1250-XZ-2
SPX1250-XZ-2
SPX1580-AAP
SPX1580-AAP
SPX1580-AAP
SPX1500-Y-2
SPX1500-Y-2
SPX1500-Y-2
To order, specify motor manufacturer, HP and pump model no. NO...
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 3
...and pull it off .
1. The lapped and polished surfaces may easily be performed with strainer attached) by removing the eight (8) housing bolts and nuts which fasten housing cover to...Remove pump housing cover (with all power shut off the impeller.
5. To remove impeller, insert screwdriver in place on motor shaft to keep shaft from turning. SEAL CHANGE INSTRUCTIONS
Power Flo™ LX ...
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 4
...pump does not develop a vacuum and pump has sufficient "priming water": 1. Check voltage to make sure pump is up , due to clean.
Clogged or restricted strainer or suction line; undersized pool...Tighten all electric power. Correct suction condition or throttle discharge lines, if practical. 3. Inspect strainer cover gasket regularly and replace as possible and determine if pump will develop a...
SP1575X15 - Page 1
... and on suction lift and horizontal length of the equipment package. Open all electric power.
Clean strainer basket regularly. Do not strike
basket to simple, common-sense procedures.
If you... filter. (The air that components such as the filtration system, pumps and heater be protected from power source. HAYWARD POOL PRODUCTS, INC.
900 FAIRMOUNT AVENUE, ELIZABETH, NEW JERSEY 07207 Make...
SP1575X15 - Page 2
...No. 10-24 Hex. Motor Strainer Housing O-Ring Basket Strainer Cover O-Ring Strainer Cover Drain Plug w/Gasket Strainer Shim Ring (Horizontal Outlet Pumps Only)
NO. Head Housing Cover Housing Gasket Impeller Seal Assembly Pump Housing Nut, No. 10-24 Hex. REQ'D.
7 1 1 1 1 1 7 1 1 1 1 1 1 2 1
PART NUMBER MODEL
SP1575X15 (With Strainer) SPX1500N2 SPX1500B SPX1500H SPX1500F SPX1500KA SPX1500AA...
SP1575X15 - Page 3
...off electrical power before restarting.
*For A.O. Carefully insert the motor shaft through the seal assembly, and secure motor to pump housing....pump to keep shaft from the "motor" side.
6.
Remove pump and motor assembly from the pump housing. To remove impeller, insert screwdriver in place on motor shaft to fill strainer with a dilute solution of the new ceramic seat with strainer...
SP1575X15 - Page 4
... gauge reading). 3. Tighten all suction and discharge valves are open and unobstructed, and that strainer cover O-ring is up to improper mounting, etc. 4. Check voltage to make sure pump is clean and properly seated. undersized pool piping. 2. Air leak in pump. 2. Vibration due to speed. 3.
Low voltage at motor (frequently caused by wear, rust...
Owners Manual - Page 1
... for one of actions that are unpredictable and unsafe.
ISPFSERIES Rev G
PowerFlo LX™ / PowerFlo II™ / EP Pump Series
Owner's Manual
Contents
Product Warnings 2 Installation 4 Start-Up & ... CAUTION warns about hazards that will or can cause severe injury and/or death.
Hayward Pool Products 620 Division Street, Elizabeth, NJ 07207
Phone: (908) 355-7995 www.haywardnet...
Owners Manual - Page 2
.../or death. o Dual suction fittings shall not be placed in suction outlet cover.
WARNING -
WARNING -
Pool and spa water circulation systems operate under hazardous pressure during pump start up .
o Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately. WARNING - Hazardous Pressure. A negative pressure applied...
Owners Manual - Page 3
... on local electrical codes for Canada] solid copper bonding wire to bond all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas piping), and conduit within 5 ft. (1.5 ... dangerous or fatal electrical shock, TURN OFF POWER to pump housing with hot tubs and spas if so
marked. Strainer cover must be used with strainer cover lock ring. WARNING - Risk of ...
Owners Manual - Page 4
... moisture and flooding. Allow adequate access for cooling. level - Pump mount must be installed below the pool water line (see Figure to be lower than pump suction connections. Piping - USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
4 Installation Instructions
Pump Location
The PowerFlo LX™ and EP series pumps MUST be new or thoroughly cleaned before use. Install...
Owners Manual - Page 5
...
Pump MUST be permanently connected to pool structure. For size of a power outage, check GFCI for tripping, which will sense a short-circuit to ground and disconnect power ...power source.
To avoid dangerous or fatal electrical shock, turn OFF power to motor before
working on the same circuit, be sure to seal wire opening on the motor housing and to all metal parts of swimming pool, spa...
Owners Manual - Page 6
... piping system. Start-Up & Operation
Prior to Start-Up
Fill strainer housing with water to motor
before draining pump.
1. NEVER operate the pump without water. CAUTION -
fill strainer and pump with water. Clean and lubricate strainer cover O-ring with compressed air can cause
components to pool/spa system directly in front of suction pipe.
Be sure all...
Owners Manual - Page 7
... petroleum or silicone lubricants as needed. 3. Tighten screws alternately and evenly. 15. Insert basket and fasten strainer cover. 16. Securely mount pump to follow instructions may result...
7 Make certain motor shaft turns freely before restarting the pump. Start-Up for swimming pool pump installation. Follow filter manufacturer's instructions for damage or deterioration ...
Owners Manual - Page 8
... level is at motor or power drop (frequently caused by removing the skimmer basket and holding your pool dealer can build up causing windings to correct cause of motor shaft.
Undersized wiring; loose connections; The motor will develop a vacuum. Be sure to burn out. Check For:
1. Make sure pump/strainer housing is filled with...
Owners Manual - Page 9
...READING (CLEAN FILTER
PUMP MODEL HORSEPOWER
FILTER MODEL
SERIAL NUMBER
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
9 Air leak in suction piping causing rumbling in pump housing. Equipment base vibrating. Maintenance
Clean strainer basket regularly. ... Change Instructions" in
this point or putting in pool, and
unrestricted discharge return lines.
Noisy...
Owners Manual - Page 10
... No.
SPX1515Z1E
Motor (for SP1780) - 1 HP
----
---- SPX1510Z2E)
*All Twist Lock versions for each pump have "TL" at end of model number to Part No. on
Refer to a "2" (i.e. Replacement Parts
Parts Diagram
PARTS LISTING
Model No. Description
SP1540C
EP1550LX
1 Housing Bolt, No. 10-24 Hex Head
SPX1500N2 (7 Req'd.)
SPX1500N2 (8 Req'd.)
2 Housing Cover
SPX1500B
SPX1580BP...
Owners Manual - Page 11
...of incidental or consequential damages, so the above constitutes the entire warranty of Hayward Pool Products with respect to its products to components manufactured by the respective manufacturer will be...of defective product, barring unforeseen delays, without charge. In no event shall Hayward Pool products be repaired or replaced, at www.haywardpool.com.
USE ONLY HAYWARD GENUINE ...
Owners Manual - Page 12
... Pool: Concrete/Gunite Vinyl Fiberglass Other
New Installation
Replacement
Installation for:
In Ground
Above Ground
Spa
Hayward is not necessary to complete warranty registration for the overall product, using the serial number that have individual serial numbers, it is a registered trademark, and PowerFlo LX, and PowerFlo II are trademarks of purchase/installation or register online...
Similar Questions
Power Flo Lx Model Sp1510z1xbc Hums Will Not Start
I have a power flo lx model sp1510z1xbc when i 1st turned on it started for a minute I shut it off a...
I have a power flo lx model sp1510z1xbc when i 1st turned on it started for a minute I shut it off a...
(Posted by christinedomon77 5 years ago)
I Am Looking For A Hayward Power Flo Lx Pump Model Sp1510-2-xes. Can You Help?
(Posted by gregjaws 8 years ago)
How To Remove A Strainer From A Hayward Power Flo Lx
(Posted by hekijsr 9 years ago)
How Does The Hayward Power Flo Lx Strainer Work
(Posted by aknapanit 10 years ago)
How To Prime Hayward Power Flo Lx Above Ground Pool Pump
(Posted by meriosdeluc 10 years ago)