Hayward Power-Flo LX Support Question
Hayward Power-Flo LX Support Question
Find answers below for this question about Hayward Power-Flo LX.Need a Hayward Power-Flo LX manual? We have 3 online manuals for this item!
Question posted by ndarbee on August 21st, 2011
Rotate Pump Housing From 90 Degrees To 45 Degrees To Attach To Canister
please provide written instructions on how to rotate the pump housing from motor to stariner housing so it connect to the canister at a 45 degree angle rather than a 90 degree angle from the pump as illistrated. Or is there a fitting or additional connector to secure the canister to the pump.
Current Answers
Related Hayward Power-Flo LX Manual Pages
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 1
... storage and reassembled to follow instructions may also be readily disassembled for the HP (KW) rating and distance from power source. A storable pool is not U.L. NOTE: If your pump is equipped with the motor's voltage, phase and cycle, and that it may be used as a means of the equipment package. provide a properly located outlet. Suction pipe...
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 2
...
SPX1500-Y-2
To order, specify motor manufacturer, HP and pump model no. SPX1510-Z-1E
SPX1510-Z-...LX
SPX1500-LX
SPX1500-LX
SPX1500-P
SPX1500-P
SPX1500-P
SPX1500-D-2
SPX1500-D-2
SPX1500-D-2
SPX1700-FG
SPX1700-FG
SPX1700-FG
SPX1500-X1
SPX1500-X1
SPX1500-X1
SPX1550-WA-1
SPX1550-WA-1
SPX1550-WA-1 DWG. DESCRIPTION
Bolt, No. 10-24 Hex. Motor-to-Housing Bolt Motor Strainer Housing...
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 3
... (ceramic seat) part of the pump housing recess. With motor removed, press the clear plastic and ceramic seat assembly out of the seal assembly:
a. Replace the assembly firmly and evenly.
9. RECOMMENDED WIRE SIZE 0-50' #14
#12
#12 For safety, all power shut off the impeller.
5. SEAL CHANGE INSTRUCTIONS
Power Flo™ LX Series with water before restarting.
* For...
Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 4
...the factory
without the expressed written authorization of motor shaft for : 1. SERVICE & REPAIRS Consult your local authorized Hayward dealer or service center. Manually check rotation of Hayward Pool Products, Inc. Wiring, loose connections, etc. 2.
Check voltage to make sure pump is necessary.
3. MAINTENANCE
1.
MOTOR CUTS OUT - D.
Check for : 1.
MOTOR HUMS, BUT DOES NOT...
SP1575X15 - Page 1
... be protected from obstruction.
4. Open all electric power. No lubrication is necessary.
3. Keep motor clean. See instructions. Shut off all suction and discharge lines and valves, as well as necessary.
2. Fill strainer housing with the motor's voltage, phase and cycle, and that vents are tight. Never operate the pump without water. Turn on back page. Inspect...
SP1575X15 - Page 2
Head Housing Cover Housing Gasket Impeller Seal Assembly Pump Housing Nut, No. 10-24 Hex. Motor Strainer Housing O-Ring Basket Strainer Cover O-Ring Strainer Cover Drain Plug w/Gasket Strainer Shim Ring (Horizontal Outlet Pumps Only)
NO. REQ'D.
7 1 1 1 1 1 7 1 1 1 1 1 1 2 1
PART NUMBER MODEL
SP1575X15 (With Strainer) SPX1500N2 SPX1500B SPX1500H SPX1500F SPX1500KA SPX1500AA SPX1500Y2 ...
SP1575X15 - Page 3
... plastic retainer, with strainer attached) by turning clockwise.
11. To remove the stationary (ceramic seat) part of pump housing-O-ring end first. b. Gently wipe the polished face of the spring seal and pull it off electrical power before restarting.
*For A.O. Reconnect pump to pump housing with a soft, dry cotton cloth.
10. SINGLE PHASE
MOTOR
KW
HP
VOLTS
CIRCUIT...
SP1575X15 - Page 4
... written authorization of obstruction. Remove and replace shaft seal. NOISY PUMP-Check for free movement and lack of Hayward Pool Products, Inc. F. Block off under abnormal conditions before damage to restricted or undersized suction line and unrestricted discharge lines. a.
Air leak in suction causing rumbling in pump housing. 5. TROUBLE SHOOTING GUIDE
A. Low voltage at motor...
Owners Manual - Page 1
...presents a potential hazard.
This is the safety-alert symbol. Hayward Pool Products 620 Division Street, Elizabeth, NJ 07207
Phone: (908) ...instructions that are important but not related to hazards. When you see this symbol on your equipment or in this manual, look for one of actions that are unpredictable and unsafe. ISPFSERIES Rev G
PowerFlo LX™ / PowerFlo II™ / EP Pump...
Owners Manual - Page 2
... heater must be positioned so as to near point. Hazardous Pressure. Before servicing pool and spa water circulation system, all system and pump controls must be in evisceration/ disembowelment. WARNING - Read and follow safety and operation instructions could cause property damage, severe personal injury, or death. WARNING - A negative pressure applied directly to follow all...
Owners Manual - Page 3
... circuit-interrupter (GFCI). Provide a properly located electrical receptacle. To reduce the risk of Electric Shock. Failure to pump housing with strainer cover lock ring. To reduce the risk of electric shock, see installation instructions and consult a professional electrician on the electrical equipment and to bond all metal parts of swimming pool, spa, or hot tub, and...
Owners Manual - Page 4
... and run is strongly advised to four (4) feet above the pool water line. To avoid pump strain, support suction and outlet independently. Installation Instructions
Pump Location
The PowerFlo LX™ and EP series pumps MUST be lower than pump inlet port.
Install pump on molded plastic components. Pump motors require free circulation of the plastic components.
Select a well-drained...
Owners Manual - Page 5
... on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to circuit. Ground motor before
working on the same circuit, be permanently connected to all electrical equipment, metal piping or conduit within 5 ft. (1.5 m) of inside walls of GFCI required and test procedures for GFCI, see manufacturer's instructions. Failure to motor nameplate...
Owners Manual - Page 6
... will not damage plastic system components; CAUTION -
Start-Up & Operation
Prior to pool/spa system directly in your pool/spa system. NEVER run pump dry. Do NOT add chemicals to Start-Up
Fill strainer housing with risk of suction pipe. STOP PUMP before starting motor. re-install on strainer cover. Replace strainer cover on vertical length of...
Owners Manual - Page 7
... the rotating and the stationary sections of motor shaft. Follow filter manufacturer's instructions for swimming pool pump installation.
WARNING - Disconnect all electrical wiring for Winterized Equipment
1. Do not use this product. Shut off water flow to pump before proceeding. 13. Note how the steel spring section of the old seal is full of the pump housing recess...
Owners Manual - Page 8
... have a timer, be able to ensure that skimmer weir is working properly. b. How to determine if pump will continue to proper levels. backwash as per manufacturer's instructions; Troubleshooting
Motor Will NOT Start - open and not blocked, that pool water level is at motor or power drop (frequently caused by removing the skimmer basket and holding your...
Owners Manual - Page 9
...Pump - Air leak in suction piping causing rumbling in pump housing. Maintenance
Clean strainer basket regularly. Equipment base vibrating. No lubrication is necessary. Keep motor... necessary.
Hayward pumps have self-lubricating motor bearings and shaft seals. Vibration due to wear or damage. See "Shaft Seal Change Instructions" in a smaller eyeball fitting...
Owners Manual - Page 10
...5 Seal Assembly
SPX1500KA
SPX1500KA
Refer to Part No. on
6 Impeller
Original Equipment
Original Equipment
7 Pump Housing
SPX1500AA
SPX1580AAP
8 Housing Nut, No. 10-24 Hex Head
SPX1500Y2 (7 Req'd.)
SPX1500Y2 (8 Req'd.)
Motor (for SW1585X25) - 2-1/2 HP
----
SPX1520Z1ESC
9 Motor (for SP1540C) - 40 GPM
SPX1540Z1E
---- SP1750, 1775, 1780
SPX1500N2 (6 Req'd.) SPX1705B SPX1580Z1...
Owners Manual - Page 11
... Authorized Service Center please visit us at our option, within 90 days of the receipt of defective product, barring unforeseen delays, without charge. Hayward shall not be responsible for any consequential, special or incidental damages of any Acts of God.
Hayward Pool Products 620 Division Street
Elizabeth, NJ 07207
▲Retain this...
Owners Manual - Page 12
.... Instead, complete warranty registration only for those individual components.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
12 PowerFlo LX™ / PowerFlo II™ / EP Pump Series Warranty Card Registration
Register online at www.hayward.com
Please Print Clearly:
Years Pool has been in service
First Name Last Name 1 year 1-3 4-5 6-10 11-15 >15
Street Address Purchased...
Similar Questions
How To Rotate Pump Return Hayward Power Flo Lx 90 Degree To 45
(Posted by lensy 9 years ago)
How To Rotate Hayward Power Flo Lx Pump Sp1510-z-1-xes
(Posted by whPebb 10 years ago)
How To Replace Bearings On A Hayward Power-flo Lx Pump Sp1580z2
(Posted by Lincmaduri 10 years ago)
How Do I Change The Pump Housing Position On My Hayward Power Flo Lx Pump?
(Posted by kiiNikki 10 years ago)
Can You Rotate The Motor Housing In A Power Flo Lx Hayward Pump From 90 Degrees
to 45 degrees
to 45 degrees
(Posted by taeni 10 years ago)