Hayward Aqua Solar GL-235 Support Question
Hayward Aqua Solar GL-235 Support Question
Find answers below for this question about Hayward Aqua Solar GL-235.Need a Hayward Aqua Solar GL-235 manual? We have 1 online manual for this item!
Question posted by mayrc54 on September 14th, 2014
All 4 Indicator Lights (power, Heating, Cooling & Check Sensor) Are Blinking
Blinking very faintly. Solar not working at all. is this a solar sensor issue?
Current Answers
Related Hayward Aqua Solar GL-235 Manual Pages
Model: GL-235 - Page 1
...damage (water/fire damage, line voltage applied to the installation instructions and specifications. Hayward warrants its solar products and IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING A WARRANTY OF... datecode on behalf of Hayward Pool Products with Hayward. Aqua Solar
GL-235
Electronic Solar Control
Operation and Installation Manual
GL-235
www.haywardnet.com
Model: GL-235 - Page 2
...If the "CHECK SENSOR" indicator remains on next page. Sensor voltages are shipped with 12VAC valves, an internal jumper can be moved to ±1%. Input power can be ...solar valve, which diverts water through the collector panels or through the normal pool loop depending on the right side of the circuit board.
2
With the sensor disconnected from the pool or spa. For safety, the GL-235...
Model: GL-235 - Page 3
... the GL-235 will have to be returned for outdoor use a PC sensor to measure the pool temperature and another PC sensor to the color code shown in figures 2 or 3. If the "CHECK SENSOR" indicator remains on and NOT blinking, there may be at fault.
10
The GL-235 provides two different types of the pool sensor as required by disconnecting the solar sensor from...
Model: GL-235 - Page 4
.... If nocturnal cooling is to measure the Solar Sensor)
Figure 5
9 Recirculate freeze protection is unprotected in series with recirculate freeze protection disabled (the jumper is present but installed on one pin only). Snap switches should be wired for Timer Override function.
4
Measuring Voltage of Pool Sensor (Use the same method to be used on a GL-235, either...
Model: GL-235 - Page 5
... Temperature" setting. The GL-235 will blink for Booster Pump Figure 4
8
5 If the valve(s) positions are off to the GL235.
Move the switch to "MANUAL OFF" and verify that all indicators except "Power" are working in reverse, follow the instructions in section marked "Low Voltage (LV) : Solar Valve" to within 1.5ºF OR the pool/spa sensor is collecting solar heat. WARNING: If...
Model: GL-235 - Page 6
Basic Installation of GL-235 Figure 2 6
GL-235 high voltage output used for Timer Override Figure 3 7
Similar Questions
Solar Sensors Changed My Sensors Now All My Lights Stay On On Manuel An Auto
(Posted by donapplegate728 6 months ago)
Orp “off” Indicator Light Is Blinking. Orp Had Been Set At 775 And W
ORP "Off" indicator light (#14 in manual) is blinking. ORP was set at 775 and was in "Auto." Cl leve...
ORP "Off" indicator light (#14 in manual) is blinking. ORP was set at 775 and was in "Auto." Cl leve...
(Posted by Cigbus 10 months ago)
Aquastar Ii Gl-235-x244. Valve Malfunction
Valve stays in Closed solar position. Even if placing valve manually in solar heating position, valv...
Valve stays in Closed solar position. Even if placing valve manually in solar heating position, valv...
(Posted by k7vk 1 year ago)
My Check Sensor Light Is On. How Do I Check Sensor?
(Posted by Anonymous-147697 9 years ago)
Power Out During Lightning/thunderstorm, Now My Hayward Aqua Plus Equip Not Wor
checked breakers, all on, and unit getting electricity, wire hot when tested
checked breakers, all on, and unit getting electricity, wire hot when tested
(Posted by nicie 10 years ago)