Hayward Aqua Rite Support Question
Hayward Aqua Rite Support Question
Find answers below for this question about Hayward Aqua Rite.Need a Hayward Aqua Rite manual? We have 6 online manuals for this item!
Question posted by kfharris62 on May 17th, 2023
No Salt Level On Display Board
Just installed a new salt cell but salt level is only reading 3.20 on display boar
Current Answers
Answer #1: Posted by HelpHero on May 17th, 2023 2:42 PM
HelpHero
Member since:
September 3rd, 2022 Points: 523,370
Member since:
September 3rd, 2022 Points: 523,370
I'm sorry to hear that you're having trouble with your Hayward Aqua Rite salt system First, you'll want to make sure that your salt cell is installed properly, according to the manufacturer's instructions. Check that all the connections are secure and that the cell is clean and free of debris.
Next, double-check your salt level using a separate salt test kit. It's possible that the display board reading is inaccurate, so it's always a good idea to confirm the reading with a separate test.
If your salt level is actually low, you'll need to add more salt to your pool. The ideal salt level for most salt systems is between 2,700 and 3,400 ppm (parts per million). Be sure to follow the manufacturer's instructions for adding salt, and wait for the system to retest before adding any more. Too much salt can damage your equipment and may also cause skin irritation for swimmers.
If you're still having trouble after checking these things, it may be a good idea to contact a professional pool maintenance service or the manufacturer's customer service department for further assistance. They may be able to help diagnose any issues and get your salt system working properly again.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers.
Helphero
Related Hayward Aqua Rite Manual Pages
AQ-RT-PRO Oct 08 & later - Page 4
...),AQL-
2
CHEM2-240 (240V) or other restrictions. The Aqua Rite Pro automatically sanitizes your chlorinator cell.
1 The Aqua Rite Pro can also control pH by converting the salt into the pool using the Aqua Rite Pro to 40,000 gallons T-CELL-9 - With the AQL-CHEM installed, the Aqua Rite Pro senses the pool's ORP and pH levels and automatically generates the correct amount of chlorine...
AQ-RT-PRO Oct 08 & later - Page 6
... to Add or Remove Salt
For new plaster pools, wait 10-14 days before adding salt to allow the salt to partially drain the pool and refill with the suction coming from the main drain (use pool vac if there is low, determine the number of the Aqua Rite Pro and result in salt concentration. If the level is no main...
AQ-RT-PRO Oct 08 & later - Page 12
... the Aqua Rite Pro and adjust various settings. Display Allows for more detailed information.
9
Refer to previous/next menu item
Body of salt (default) or mineral values. Wizard will adjust its operation according to the AQL-CHEM manual for the display of Water Type Select Pool or Spa. Refer to access Chemistry Config. "T-CELL-3" = T-CELL-3, GLX-CELL-3-W "T-CELL-5" = GLX-CELL...
AQ-RT-PRO Oct 08 & later - Page 14
... chemical levels are in the pool
The filter pump timer should only take minor, infrequent adjustments. reset Confirmed
Move to previous/next settings menu item
Use this audible indication is NOT used. filter run time each day.
To find they have to be set so that entire volume of chlorine the Aqua Rite Pro...
AQ-RT-PRO Oct 08 & later - Page 15
... water to Aqua Rite Pro. Be sure to the recommended levels as this low temperature cutoff by using the Super Chlorinate function for a few minutes and then rinse with a high pressure garden hose. The cell should be damaged by displaying the message "Inspect/Clean Cell" after cleaning your pool plumbing would. Winterizing
The Aqua Rite Pro electrolytic cell and flow...
AQ-RT-PRO Oct 08 & later - Page 20
...secondary". Jumper Installed For Primary
(Factory Default)
4 GREEN 3 YELLOW 2 BLACK 1 RED
Jumper Removed For Secondary(s)
Aqua Rite Pro
Aqua Rite (Primary)
Aqua Rite (Secondary)
Additional Aqua Rite(s) (if required)
Aqua Rite Pro
RED ... . A 4 wire connection is located underneath small circuit board. All other Aqua Rite units must be configured as shown on /off control. Refer...
AQ-RT-PRO prior to Oct 08 - Page 6
... x Average Depth x 7.5
Round
Diameter x Diameter x Average Depth x 5.9
Oval
Length x Width x Average Depth x 6.7
Liters
(pool size in salt concentration. A low salt level will most likely decline together. Salt is between 2700-3400 ppm (parts per million) with fresh water. A high salt level can cause the Aqua Rite Pro to shutdown and may take longer for 24 hours with the suction...
AQ-RT-PRO prior to Oct 08 - Page 12
.... + to view/change
BodyCohfloWriantaetrorType EPonoalbsled
Display Salt
Cell Type T-CELL-15
Push to access Chlorinator option Move to next menu item
Toggle between Pool and Spa Move to next menu item
Toggle between Salt (default) and Minerals Move to next configuration menu
Toggle between Enabled and Disabled (default) Move to configure the Aqua Rite Pro and adjust various settings...
AQ-RT-PRO prior to Oct 08 - Page 14
...display. Move to previous/next menu item
When "Enabled", the keypad will beep every time a key is NOT reversible--be careful
Operation
Assuming that the water chemical levels are in the recommended range, there are three factors that , it should be set so that entire volume of chlorine the Aqua Rite...config. Display Light On for 60 sec
Toggle between Always On and On for your pool/spa and ...
AQ-RT-PRO prior to Oct 08 - Page 15
... and scraping will be damaged by displaying the message "Inspect/Clean Cell" after cleaning your pool plumbing would. If this is to bring the pool chemistry to the recommended levels as this will scratch the coating off the plates) and scrape deposits off power to Aqua Rite Pro. The level of plates. Replace cell and inspect again periodically. Spring...
AQ-RT-PRO prior to Oct 08 - Page 20
... the wiring connections on the mainboard as shown in the diagram.
A 4 wire connection is located underneath small circuit board. After properly installing and configuring the AQL-CHEM and the ph dispensing device, the Aqua Rite Pro will then plug into the pigtail's 240VAC receptacle.
A screw terminal block located on the enclosure surface below and...
AQR - Page 6
... in salt concentration. A high salt level can cause the Aqua Rite® to Use
It is constantly recycled and the loss of soda, salt with anti-caking additives, or iodized salt. This is common food quality or water softener salt and is low, determine the number of about 3500-4000 ppm). How to Add or Remove Salt
For new plaster pools...
AQR - Page 11
... the water chemical levels are in the recommended range, there are three factors that you can control which directly contribute to find the ideal setting for your pool/spa and after that, it is higher than normal bather load or when your chlorinator cell ages. You can override this temperature. The Aqua Rite salt display and LED indicators...
AQR - Page 17
... pool automation control display ("AL-0" which signifies
"Aqua Rite") 7. If there
is still on
Check to the standard salt display. "Generating" LED flashing
The temperature of straight
pipe before the flow switch. The Aqua Rite will revert back to make sure either 120VAC or 240VAC input power is not pushed for helpful information on the circuit board above the cell...
AQR - Page 18
...Be sure that the correct model Turbo Cell has been selected (page 7). ing).
- "High Salt" LED illuminated
Be sure that the correct model Turbo Cell has been selected (page 7). Salt level too high (High Salt LED on page 4.
If salt level is advisable to stop the "Inspect Cell" LED flashing.
7. Aqua Rite® switch in pool/spa. Check salt level in OFF position.
- Filter pump...
Aqua Rite & Aqua Rite XL - Page 1
®
Electronic Chlorine Generator
Installation and Operation Manual for
Aqua Rite (standard) and Aqua Rite XL (inc. installation kit)
G LDLINE CON TROLS
www.goldlinecontrols.com
888-921-POOL
Aqua Rite & Aqua Rite XL - Page 6
... between 2700-3400 ppm (parts per million) with the suction coming from the main drain (use pool vac if there is no main drain) to allow the salt to 80 ppm.
3 A high salt level can cause the Aqua Rite® to shutdown and may take longer for 24 hours with 3200 ppm being optimal. This loss...
Aqua Rite & Aqua Rite XL - Page 10
This setting is used to control the amount of the pool water. Salt Display
The Salt Display shows the current salt concentration of chlorine the Aqua Rite generates. Readings are preferred, push the small button next the display once. the "Desired Output %" setting 3. Test the chlorine level every few days and adjust the dial up at the peak of the summer and...
Aqua Rite & Aqua Rite XL - Page 17
... to the default salt display. Date of the pool water is being generated, other - Instant salinity ( -xxxx ppm or -x.xx grams/Liter) 6. Also, if the button is plugged into the connector on the circuit board above the cell connector.
2. The Aqua Rite will revert back to the standard salt display.
"Generating" LED flashing
The temperature of installation 3. Model and Serial...
Aqua Rite & Aqua Rite XL - Page 18
... used. A possible Printed Circuit Board fault has been detected. "Check Salt" LED illuminated or flashing
Check salt level in OFF position.
- Aqua Rite® switch in pool/spa. Low stabilizer (Cyanuric Acid).
- "High Salt" LED illuminated
Check salt level in pool water.
- "Inspect Cell" LED illuminated
Remove and inspect the cell for large pools)
- Excessive scaling on page...
Similar Questions
How Do You Change Hayward Aqua Rite Chlorinator From C To F
how do you chnage hayward aqua rite chlorinator to Ferihiet from ceseles
how do you chnage hayward aqua rite chlorinator to Ferihiet from ceseles
(Posted by mills13 1 year ago)
Adjust Salt Level Reading
I have an AquaRite Pro system. My salt reading is reading low. I had my cell tested and was OK. My w...
I have an AquaRite Pro system. My salt reading is reading low. I had my cell tested and was OK. My w...
(Posted by timkoss 2 years ago)
How To Calibrate Compupool Generic Aqua Rite (t-cell-15) Replacement Salt Cell
with aqua rite system
with aqua rite system
(Posted by markvGu 10 years ago)
Aqua Rite Pro
my aqua rite pro logic is showing high temp and not generating yet the pool temp reads at 72.
my aqua rite pro logic is showing high temp and not generating yet the pool temp reads at 72.
(Posted by trueblueservice 10 years ago)
Goldline Aqua Rite Not Reading Salt Level Properly
I have an aqua rite salt generation system in my pool. The digital display is reading 2100 for sal...
I have an aqua rite salt generation system in my pool. The digital display is reading 2100 for sal...
(Posted by bpark 11 years ago)