Hayward Aqua Plus Support Question
Hayward Aqua Plus Support Question
Find answers below for this question about Hayward Aqua Plus.Need a Hayward Aqua Plus manual? We have 4 online manuals for this item!
Question posted by 2pistons on June 2nd, 2012
My Aqua Plus Computer Keeps Indicating Low Salt (2200 Ppm) Yet Per Salt Strip
reading and pool water analysis it's at 3200 ppm. My auto chlorinator is turning off due to low salt reading. The cell has been cleaned and looks very clean..
Current Answers
Related Hayward Aqua Plus Manual Pages
Model: PL-PLUS Installation - Page 4
... Config. This requires a manual pH test of the pool water using natural stone for coping or for mounting Aqua Plus and remote display/keypad Valves (use of stone used around a saline pool with electronic chlorine generator in your chlorinator cell. The probes must be clean and free from main panel to Aqua Plus Wire/conduit for filter pump and other high...
Model: PL-PLUS Installation - Page 5
... the salt level and stabilizer.
If Si equals .2 or more than one set of turn-on enabling/disabling the chlorinator (see page 20). The default selections are using the chlorinator features on /turn -off times for the Aqua Plus are NOT using the chlorinator, it is selected then the user can enter one of the standard Aqua Plus functions. Pool/Spa, Button...
Model: PL-PLUS Operation - Page 4
... Aqua Plus automatically converts the salt into free chlorine which is part of the control functions can control pumps, valves, lighting, heaters, and chlorination. Chlorine will be shown only if the chlorinator is enabled. The current status of three)
Water
Temperature Sensors
Air
Solar
External Input
Optional Flow Switch
Filter Pump Lights Aux 1
120/240V Relays
Aux 2
Pool/Spa...
Model: PL-PLUS Operation - Page 5
... --
The Aqua Plus will automatically scroll through the cell 84ºF is the water temperature at the cell 3200PPM is the "instant" salt level at the cell. • ORP High - Check the chlorinator for 15 seconds and then turn the Aqua Plus control power circuit breaker on the cell, and the cell aging. if AQL-CHEM is used around a saline pool with fresh water.
Refer...
Model: PL-PLUS Operation - Page 6
... FILTER button again to be cleaned or replaced.
• ORP Probe Error -- If the chlorinator cell voltage is active. x is to automate the operation of your pool/spa system, there may need to turn on the printed circuit board.
• Check Flow Switch -- Manual System Operation
While the main objective of the Aqua Plus is the same decimal...
Model: PL-PLUS Operation - Page 7
..." button once will turn off while the pool/spa valves are disabled (except for Lights and Aux outputs. Press "" to inspect theAqua Plus chlorinator cell approximately every 3 months and clean the cell if necessary. For optimum operation, you can be illuminated and the Aqua Plus will switch the Aqua Plus to reset the timer.
• Low Salt/Minerals or Very Low Salt/Minerals -- If the...
Model: PL-PLUS Operation - Page 8
... equipment automatically in -home remote display/keypad. The Aqua Plus will make the values auto scroll.
To acid wash, turn off . Remove cell from a Menu
"+" and "-" Buttons Adust
> >
>
There are visible, reinstall. If any chlorine based shock product and balance the pool water chemistry per the levels indicated in the direct sunlight to the appropriate levels. The electronic...
Model: PL-PLUS Operation - Page 10
...) of Pool/Spa water
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
(242)...spa only" or "pool and spa" operation and the solar control is enabled. The Aqua Plus will automatically switch to the default menu when no keys have both solar heat and a conventional heater and the solar priority option is selected (Configuration Menu), then the conventional heater will turn on whenever the pool/spa...
Model: PL-PLUS Operation - Page 12
... backlight on the Aqua Plus Control. Use the chart below -0.2, the water is an indicator of the default menu. Move to use: Measure pool pH, temperature, calcium hardness,
and total alkalinity. In other chemistry recommendations besides salt. These values are used for all display/keypads. If this option for the Aqua Plus are currently using the chlorinator features on...
Model: PL-PLUS Operation - Page 14
... for the pool and spa must be the period of time when the pump will turn heater permanently off " and the heater will not operate regardless of the spa period, the Aqua Plus will take more than one reason for 3 minutes to prime and establish water flow. For all the time. If the high speed and low speed...
Model: PL-PLUS Operation - Page 15
... off at the designated times. During the programmed spa time, the Aqua Plus will turn on during the programmed on the filter pump and move the pool/spa valves into the "spa-only"
position. Aux1 and Aux2 configurations are indications that some pool
equipment (example pressure side pool cleaner) can also manually turn on /off time, it
may be because of...
Model: PL-PLUS-16V Installation - Page 5
... the Aqua Plus 16v subpanel. 4. Check that the Aqua Plus 16v is calling for remote control operation-refer to the Settings Menu / Pool Solar & Spa Solar and temporarily lower the temperature settings below the current water temperature.
2. If the "Heater" LED is set as high as indicated by the "Heater" LED being illuminated. Plumbing (page 8) General Pool Equipment Chlorinator Turbo Cell...
Model: PL-PLUS-16V Installation - Page 6
...the water and is recommended that the probes need to calibrate, and inconsistent readings are indications that you are recommended by the Association of ColorLogic configuration parameters
Default Press +
Move to erase all of the Aqua Plus 16v configuration menu for the Aqua Plus 16v are using the chlorinator features on enabling/disabling the chlorinator (see page 24). Clean Probe...
Model: PL-PLUS-16V Installation - Page 18
... is active. Valve3 and Valve4 are dedicated to the pool/spa suction (Valve2) and return (Valve1) valves. The relay will be forced off , the relay will turn on .
Also, this speed.
2-Speed pumps: Select high (default) or low speed operation.
Low Voltage Wiring
Valve Actuators The Aqua Plus 16v can be connected to most heaters also include...
Model: PL-PLUS-16V Operation - Page 7
... Minerals" (if Chlor. is enabled and the AIR temperature sensor falls below the preset freeze protection temperature, the Aqua Plus 16v will turn on the spa filter pump to circulate the water. There is less than the "average salt" value which shows the dimmer output level (Off - The delay time is displayed.
43
Two Speed Filter...
Model: PL-PLUS-16V Operation - Page 8
... cell is detected. Service
The main unit keypad has a "SERVICE" key. The red "SERVICE" LED will be illuminated and the Aqua Plus 16v will remain in this button will turn off part of these issues, go to normal (automatic) operation.
If the CSM indicates that the function of 950mV or higher is higher than the pool/spa water...
Model: PL-PLUS-16V Operation - Page 10
... Aqua Plus 16v will allow you will be manually controlled by pressing the "Service" button.
The Service mode will stop generating chlorine under certain high salt conditions in your system is either an open or short circuit.
• Spa sensor for emergencies). Pressing the "SERVICE" button once will alert you believe your pool and/or spa system. Clean...
Model: PL-PLUS-16V Operation - Page 11
... quarts of freezing temperatures, be found on the cell indicates that there is an unusually high calcium level in the pool (old pool water is usually the cause). It may require periodic cleaning. The heater will turn on the plates. To acid wash, turn on the previous page shows the Aqua Plus 16v's six menus as well as this by...
Model: PL-PLUS-16V Operation - Page 15
... will be used by the Association of the filtration period. The Countdown timer is programmed in low speed during the overlap period. The Aqua Plus 16v allows more information). For pool/spa combination systems with "Filter Hi"). These include super-chlorination, spa operation, manual operation, heater cooldown, freeze protection, heater-extend and solar-extend.
12 If you...
Model: PL-PLUS-16V Operation - Page 17
..." or "Pool Heater" is the first spa filter timeclock and will automatically switch to previous/next menu item
This menu will keep the relay
off for more than normal bather load or when your chlorinator cell ages. Set the Heater Temperature (or turn on and the valves are long periods of the programmed low speed time period...
Similar Questions
Aqua Plus Sub Panel Question
I had an aqua plus system installed 8 years ago. Now my wife wants to add a hot tub in the back yard...
I had an aqua plus system installed 8 years ago. Now my wife wants to add a hot tub in the back yard...
(Posted by Nickmalone81 1 year ago)
Check System - Very Low Salt
My cell is not operating and the screen indicates it is because of low salt. However the salt level ...
My cell is not operating and the screen indicates it is because of low salt. However the salt level ...
(Posted by jjcebrown 7 years ago)
Goldline Aqua Rite Not Reading Salt Level Properly
I have an aqua rite salt generation system in my pool. The digital display is reading 2100 for sal...
I have an aqua rite salt generation system in my pool. The digital display is reading 2100 for sal...
(Posted by bpark 11 years ago)