Hamilton Beach HBH650 Support Question
Hamilton Beach HBH650 Support Question
Find answers below for this question about Hamilton Beach HBH650 - Bar Blender - Tempest 64oz.Need a Hamilton Beach HBH650 manual? We have 1 online manual for this item!
Question posted by macmcd on April 21st, 2014
How To Set Clock On Hamilton Beach Model P100n30al-s3
I have the above model microwave oven and am having a problem figuring out how to set time and as 12-hour clock.
Current Answers
Related Hamilton Beach HBH650 Manual Pages
Operation Manual - Page 2
...blender. Disconnect power before putting on .
16. Not intended for short periods of lid. To prevent possibility of serious personal injury, keep hands out of two-piece lid. Blades are loose, discontinue use by Hamilton Beach may push lid off parts.
8. The use .
12...injuries.
14. Always operate blender with all equipment operators as part of an oven mitt or thick towel,...
Operation Manual - Page 3
... not use caution when blending hot contents. We recommend keeping a replacement container and cutter on container when blending. Electrical Shock Hazard Disconnect power before cleaning blender base. Do not put hands, spoons, or other injuries. Place empty container on base and run on HIGH speed for 2 seconds to follow these instructions...
Operation Manual - Page 4
Removable Filler Cap
Lid
64 oz. Become familiar with all parts and features before using your blender. Polycarbonate Container
Blender Base
Reset Switch/ Circuit Breaker
Control Panel
Timer Knob*
*
= 3 Min. Your Tempest blender is designed for the Tempest blender are shown on this page.
Max
Stop
High Speed Low Speed Jump Cycle 4
Cutter Assembly Jar Pad
5 10...
Operation Manual - Page 5
...the desired function (HIGH, LOW or JUMP). Depending on the model of your blender, the plug will look like the following to turn the blender ON (I). Press the Power ON (I ).
6. Place the ... LOW to desired run time.
7. Read Important Safety Instructions and Warnings before use.
2. NOTE: Use the Jump Cycle for the blender. Quick Start Guide
1. Place the blender on the base with ingredients...
Operation Manual - Page 6
Max 6 1
2
3
4
Press Power ON (I).
5
Set operating time.
6
Select speed. OR
= 3 Min.
Operation Manual - Page 10
Thermal Overload Protection
1
2
3
4
5
6
00:00 Remove jar within
:03
10
00:02:00
Blender will automatically turn off after 2 minutes of low-speed "cool down cycle".
Operation Manual - Page 12
Troubleshooting Guide
Problem . . .
Motor ...are loose, discontinue use immediately and replace the blades. Replace cutter assembly at all times.
• Solid pieces are too large.
• Container is properly seated. Do...the cutter by rotating the drive end of the blender base.
See "Thermal Overload Protection" for details.
12
Attempt to run "cool down cycle" or ...
Operation Manual - Page 13
...Alaska, and Hawaii
Hamilton Beach Commercial understands that it's better for your bottom line and your peace of mind. You'll find that your equipment breaks down, you have model, series, and... service staff (hours Monday - This warranty gives you specific legal rights and you . Some states do not allow limitations on -site maintenance cannot be presented;
Hamilton Beach/Proctor-Silex, ...
Similar Questions
Do You Sell The Blender Model #52204 By It Self?
i would like to know if you sell the Hamilton beach blender model # 52204, i have try other places, ...
i would like to know if you sell the Hamilton beach blender model # 52204, i have try other places, ...
(Posted by sisra8 6 years ago)
Instructions For The Hamilton Beach Little Mac--model 2508
need instructions for model 2508
need instructions for model 2508
(Posted by lmmg1940 10 years ago)
Mini Nylon Utensil Set
how do you get the metal triangle off the Hamilton Beach nylon mini utensil set?
how do you get the metal triangle off the Hamilton Beach nylon mini utensil set?
(Posted by bridgetblack 10 years ago)
How Do I Adjust The The Power Level On Model Hb-p100n30al-s3/ P100n30als3b ?
(Posted by mervin1949 10 years ago)
What Is The Value And Year Of A Hamilton Beach Blender, Model # 722-2.
This is all I need to know, it is an old blender that was given to me. wendy
This is all I need to know, it is an old blender that was given to me. wendy
(Posted by angelfood888 10 years ago)