GE NX-1448E Support Question
GE NX-1448E Support Question
Find answers below for this question about GE NX-1448E - Security NetworX 48-Zone Fixed.Need a GE NX-1448E manual? We have 1 online manual for this item!
Question posted by Byurkiw on August 9th, 2012
Zone Number Flickering (wireless Magnetic Contact On Door).
Zone number flickering even though batteries were replaced. There is a wireless magnetic contact on the door of this zone.
Current Answers
Related GE NX-1448E Manual Pages
User's Manual - Page 4
... mean will obtain with this system.
2.
Keep in mind, the level of security devices attached to 60 icons and a built-in an accessible location for your home/business.
Your security system is an electronic device and is described in the security system not working properly.
If you do so could result in the booklet...
User's Manual - Page 6
... INSTANT ICON 12 LISTEN-IN ICON 12 POWER ICON 12 READY / NOT READY ICON 12 SILENCED ICON 12 STAY LIGHT 12 TAMPER/TROUBLE ICONS 12 ZONE ICON 12 KEYPAD FUNCTIONS 13 ARMING YOUR SYSTEM IN THE "AWAY" MODE 13 ARMING YOUR SYSTEM IN THE "STAY" MODE 14 USING THE QUICK ARM...
User's Manual - Page 7
... EMERGENCY EVACUATION PLANS 26
NX1448E Icon Keypad
Page 7 (Table of Contents continued...)
DISARMING THE SYSTEM 15 CANCEL / ABORT FEATURE 16 BYPASSING ZONES 16 GROUP BYPASS 16 UNBYPASSING 17 TURNING THE DOOR CHIME ON AND OFF 17 CHANGING USER CODES 17 ASSIGNING USER CODE AUTHORITY LEVELS 18 OTHER KEYPAD FUNCTIONS 20 SETTING THE...
User's Manual - Page 8
.... NX1448E Icon Keypad An option that has been programmed by the installer to bypass multiple zones with one or more zones open.
Can be either a four (4) or six (6) digit code that allows the ...the ready icon. (Note: Those zones that allows the user to operate a device. An option that allows the keypad to sound a ding-dong whenever an entry/exit door is either User Codes (relating to ...
User's Manual - Page 10
... a monitoring center, an emergency report could be transmitted to that center. This key can activate the auxiliary alarm when pressed for two seconds.
If your security system will respond to that requires response by emergency personnel.
Your system may not be sent to the Panic/Hold-Up activation. This key can...
User's Manual - Page 11
...delay. EXIT LIGHT
The exit light is "on"; The user may want to come on.
The zone(s) that is flashing, all abortable reports will cause the cancel light to disarm the system if ... UNDERSTANDING THE ICONS & LIGHTS
ARMED ICON
The armed icon is "on" when the system is "off", no zones are bypassed.
"off " when it is flashing in a trouble condition. Entering a code followed by the [...
User's Manual - Page 12
.... The not ready icon is on when an NX-534 is active in listen-in trouble.
ZONE ICON
The zone icons are bypassed. LISTEN-IN ICON
Listen-in ...zone(s) is tampered or in mode. TAMPER/TROUBLE ICONS
The tamper or trouble icon is in a trouble condition. If a zone icon is "flashing" rapidly, it means that zone is on page 23 of an entry/exit door will flash if the system has a low battery...
User's Manual - Page 13
...zones are bypassed, a sensor in that the exit time is about to expire.
NX1448E Icon Keypad
Page 13 If not, contact...zone can be on or flashing when all protected doors and windows. • Ready icon will be violated without affecting the ready icon. • The security...zones and
sensors are secure. The user may now leave the building. Trouble conditions are: Tamper Hardware
Low Battery...
User's Manual - Page 14
....
Page 14
NX1448E Icon Keypad If not, contact your 4 or 6 digit user code. • If "Auto Bypass" is enabled, if you do not leave through a designated entry/exit door. If Auto Bypass is enabled, omit Step 3. • When "Auto Instant" is enabled, all interior zones are secure.
Restore power if possible. ARMING YOUR SYSTEM...
User's Manual - Page 15
... of the entry delay, an alarm will illuminate indicating that the entry/exit doors have no entry delay. The security system is flashing during the entry delay, the alarm system has been activated in...key will create an alarm. The armed icon will go off (toggle) all designated interior zones. (Optional) When armed, pressing the [EXIT] key will start the exit delay, enabling you will turn ...
User's Manual - Page 16
...followed by the [CANCEL] key while this must be done while the system is flashing, all zones that need to come on until the central station has received the cancel report.
press the ... alarm report to the central station will stop flashing upon exiting the Bypass Mode. The corresponding zone icon will stay on . Enter user code, if required (optional). Leave the building immediately ...
User's Manual - Page 17
...door chime is on the chime light will display.
N For partitioned systems, someone changing the code of
another person must be off.
The corresponding icon for user 3.)
The instant icon will flash and zone...be illuminated. NOTE: All zones will flash. If the chime is already bypassed.
Enter a ["Master Arm/Disarm" Code].
Enter the 2-digit "user number".
(Always enter 2 ...
User's Manual - Page 18
...beep 3 times. ASSIGNING USER CODE AUTHORITY LEVELS
Assign authority levels to users by pressing the number for that authority level.
An explanation of another "user code" needs to be assigned ... 1
Step 2 Step 3 Step 4
Press [r]-[6]-["Master Arm/Disarm Code"]. Enter the 2 digit "user number" to be programmed, return to which they have access. when all icons are all icons are off ...
User's Manual - Page 19
... where you to the partition enable. (The user has access in partitions that are illuminated.)
The illuminated numbers indicate each partition where the user has access. ICON 1 2 3 4 5 6 7
8
AUTHORITY ... Arm Only Arm Only After Closing Time Master Arm/Disarm (can program other codes) Arm/Disarm Bypass Zones Open / Close Reporting If this icon is on, this code is on constant and instant icon is ...
User's Manual - Page 20
... between 1 and 8 to exit the Assigning Authority Level Program. Step 4 If another user number to all user numbers.
Keypad is pressed, the system will make the keypad sounder go to Step 2 previously mentioned. The zone(s) that created the last alarm will go to higher tones, pressing the [-] key will remain in the new...
User's Manual - Page 21
... still beeps after repeated attempts, please contact your code to silence the keypad. Enter Code icon will appear flashing.
The service icon will display. Step 1 Step 2
Press [r]-[7]. Step 2 Enter a ["Master Code"]. Step 2
The ALARM MEMORY feature will flash those zones that created alarms and will perform a battery test, communicator test, and/or a siren...
User's Manual - Page 23
... will flash and the zone icon(s) will be on .
SETTING THE KEYPAD LIGHTING
Step 1 Press [r]-[9]-[1]. It is "on " if the security system requires service. Press...2
PROBLEM
SYSTEM FAULT - If a zone(s) is required. Press the [#] key to return to the system fault(s) below:
1 Over Current Fault 2 Siren Trouble 3 Box Tamper
5 Expander Low Battery 6 Expander Box Tamper 7 Expander Trouble...
User's Manual - Page 24
...
LOSS OF SYSTEM TIME - This only
applies to wireless zones. Press the [#] key to return to the 1 of 8
service icons.
4
ZONE LOSS OF SUPERVISION - Press the [6] key. Refer ... Line Cut
7 = Aux communication device failure
The service icon will illuminate showing which zone(s) has a low battery. The
zone icon(s) will illuminate as they correspond to be reset. Press the [#] key to exit...
User's Manual - Page 25
...3 times once every minute for 12 hours. Please contact your system will silence the keypad for Sensor/Zone Low Battery or Loss of the following conditions are bypassed.
Pulses... keypresses.
Beeps for 1 second or emits a "ding-dong" sound for any zone(s) are detected: Zone or Box Tamper, Low Battery, AC Power Fail, or Expander trouble. If programmed, your system keypad may sound...
User's Manual - Page 26
... National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
In a home, sleep with the National Fire Protection Association's Standard 72. The following steps...Security System has been completed, notify your home or business should be used as a guide in . Show windows, doors, stairs, and rooftops that opens easily. Set a meeting in accordance with bedroom door...
Similar Questions
Entry Delay
How do I reset my system so the alarm goes off 60 seconds after entry instead of 30 seconds after en...
How do I reset my system so the alarm goes off 60 seconds after entry instead of 30 seconds after en...
(Posted by larrycarol195 11 months ago)
The Audible Countdown Warning Sometimes Occurs For No Apparent Reason
On two consecutive evenings the audible countdown warning came on without our having used any panel ...
On two consecutive evenings the audible countdown warning came on without our having used any panel ...
(Posted by flemingraf 1 year ago)
How2resolve Exp Wireless Jam Dev 0 Report? System= Nx148, Nx 6se
Since a week ago I receice the following report "EXPANDER WIRELESS JAM(device 0))" on my ultrasync a...
Since a week ago I receice the following report "EXPANDER WIRELESS JAM(device 0))" on my ultrasync a...
(Posted by famberentsen 3 years ago)
Change Security Code For: Ge Networx With Nx-1448e Keypad
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
(Posted by Jim39164 8 years ago)
Nx-1448e How Do You Change The Phone Number It Dials When It Alarms?
(Posted by hubbard007 8 years ago)