GE NX-1448E Support Question
GE NX-1448E Support Question
Find answers below for this question about GE NX-1448E - Security NetworX 48-Zone Fixed.Need a GE NX-1448E manual? We have 1 online manual for this item!
Question posted by mlyoung on December 11th, 2022
How Do You Disarm The System When Your Code Does Not Work?
I have a NX-1448E system installed in 2003. I used my code to engage the alarm stay function. When I re-entered my code to turn the alarm stay function off, it did not work. I can turn on and off the instant function, the chime, and the exit - but I can not turn the alarm stay off.
Current Answers
Answer #1: Posted by Odin on December 11th, 2022 10:52 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
1. If the red armed light is flashing during the entry delay, the alarm system has been activated in your absence. Leave the building immediately.
2. The cancel light, if enabled, will flash during an abort delay time. If a code is entered followed by the [CANCEL] key while this light is flashing, all abortable reports will stop the communication process.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/general%20electric.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Answer #2: Posted by SonuKumar on December 11th, 2022 8:36 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
https://www.manualslib.com/manual/394989/Ge-Nx-1448e-Security-Networx-48-Zone-Fixed.html?page=21#manual
rest function
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related GE NX-1448E Manual Pages
User's Manual - Page 2
SECURITY SYSTEM NOTES
Installing/Service Company For Service Call Central Station
Duress Code
This system is
is not
partitioned.
EMERGENCY ACTIVATION KEYS (check if enabled)
Fire
Auxiliary Emergency
Police
Abort Delay (s) Auto Bypass (s) Auto Instant Battery Test
PROGRAMMED FUNCTIONS Cancel Alarm Change Partitions Chime Communicator Test
Forced Arming (s) Group Bypass (s) Quick...
User's Manual - Page 4
... able to turn on it as your home/business. INTRODUCTION
This manual is subject to failure or malfunction. If you should read and follow the instructions in its operation. The system must always be tested weekly. You should be disarmed using a 4 or 6 digit code. Do not rely on (ARM) your System by entering a 4 or 6 digit code into...
User's Manual - Page 5
...removed to provide notification of an alarm event. Your system will need to be possible to install and maintain your security control system.
Smoke and heat ...security system. NX1448E Icon Keypad
Page 5 Warning devices will not work without the backup battery connected.
Care should be taken to plug in all situations.Use qualified security professionals to arm the security...
User's Manual - Page 7
... continued...)
DISARMING THE SYSTEM 15 CANCEL / ABORT FEATURE 16 BYPASSING ZONES 16 GROUP BYPASS 16 UNBYPASSING 17 TURNING THE DOOR CHIME ON AND OFF 17 CHANGING USER CODES 17 ASSIGNING USER CODE AUTHORITY LEVELS 18 OTHER KEYPAD FUNCTIONS 20 SETTING THE KEYPAD TONE 20 CHANGE PARTITION - Optional 20 VIEW ALARM MEMORY 20 TEST FUNCTION - Optional 21 RESET FUNCTION 21...
User's Manual - Page 8
...) or Function Codes (a toggle switch to be turned on /off). A master arm/disarm code that allows a delay in reporting to disarm. An option that indicates the alarm system is opened. An option that allows an instant alarm condition for Entry/Exit doors, or grants a delay to allow someone to enter/exit the building without an alarm, or before entering a user code to...
User's Manual - Page 9
... 44 45 46 47 48
NX1448E Icon Keypad
Page 9 An option that allows you to arm or disarm the system.
A four (4) or six (6) digit entry code used to turn on (ARM) the security system by pressing either the [STAY] or [EXIT] key on the keypad control (for ARMING only) as programmed by the installing company. The outer edge...
User's Manual - Page 11
...zone has been faulted. Note: The cancel feature must be enabled. Please note that the light will flash during an abort delay time. Entering a code... come on. The zone(s) that a fire zone is bypassed will flash when there has been an alarm during the exit delay... bypass light is disarmed. Note: The abort feature must be enabled. CANCEL LIGHT
The cancel light will stay on until the ...
User's Manual - Page 12
.... The power icon will produce an immediate alarm.
If a zone icon is "flashing", that the zone is in mode. The instant icon can be "on when an NX-534 is active in listen-in a trouble... after a code has been entered to force arm.
INSTANT ICON
The instant icon is "on" when there is no delay on or off by pressing the [Stay] key while the system is armed. A zone icon will...
User's Manual - Page 13
... "flashing" light.)
KEYPAD FUNCTIONS
ARMING YOUR SYSTEM IN THE "AWAY" MODE
AWAY is used when the user is off...Alarm/Fault and Tamper/Trouble will illuminate. • You may wish to expire. Step 2 Enter your installing company listed on or flashing. • If the power icon is away from the premise and wants the interior protected. Step 1
Close all protected zones and
sensors are secure...
User's Manual - Page 14
ARMING YOUR SYSTEM IN THE "STAY" MODE
STAY is used when the user is enabled, omit Step 4. Restore power if possible.
If not, contact your 4 or 6 digit user code. • If "Auto Bypass" is enabled, all protected zones and
sensors are bypassed.
Step 1
Close all protected doors and windows. • Ready icon must be on or...
User's Manual - Page 15
... an "Instant" mode, press the [STAY] key again.
• The instant icon will allow the user to be used for a maid or baby sitter code, etc.
otherwise you plan on /off (toggle) all designated interior zones. (Optional) When armed, pressing the [EXIT] key will not disarm the security system. If a valid code is enabled. Quick Arm will...
User's Manual - Page 16
... (Optional, see page 1)
The cancel light will flash during or after an alarm report to bypass one or more zones, this light is in the disarmed state. If a code is entered followed by the [0] key, then the [BYPASS] key again, all abortable reports will stay on .
GROUP BYPASS
By pressing the [BYPASS] key, followed by the...
User's Manual - Page 17
... the bypassing procedure on a zone that zone will toggle the chime feature on/off by pressing the [CHIME] key while the system is disarmed.
Enter a ["Master Arm/Disarm" Code].
If the chime is already bypassed. NX1448E Icon Keypad
Page 17 TURNING THE DOOR CHIME ON AND OFF
The door chime is turned on the chime light will be...
User's Manual - Page 18
... [#] key while the ready icon is blank;
Step 1
Step 2 Step 3 Step 4
Press [r]-[6]-["Master Arm/Disarm Code"].
The ready icon will beep 3 times. Icons illuminated indicate the authority levels assigned to view the next digit or enter new 4-
While using the [•] and [-] keys, you are off ) the authority level by pressing the number for...
User's Manual - Page 19
...moves you want to give the user access or deny access. (Example: If zone icon #2 is lit, then the user is assigned access to partition #2. ... IS OFF Reserved (Note: Do not change if on.) Arm Only Arm Only After Closing Time Master Arm/Disarm (can program other codes) Arm/Disarm Bypass Zones Open / Close Reporting If this code is programmed as a function code. Step 5 Step 6
Press the [r] key.
User's Manual - Page 21
...the siren test is used to reset Smoke Detectors, Zone Troubles, and Zone Tampers.
RESET FUNCTION
This function is performed, enter a user code to silence the keypad. If the keypad still beeps after repeated attempts, please contact your code to silence the siren. Enter Code icon will appear flashing. The service icon will display.
TEST FUNCTION - Alarms and reports will not...
User's Manual - Page 22
... always be two (2) digits.
Note: The clock is a 24-hour clock.
SETTING THE SYSTEM CLOCK
Step 1 Press [r]-[9]-[7]. Example: 7 minutes after would be entered [0]-[7]. Example: The 5th would be entered as [0]-[5]. Enter Code icon will come on constant. Must always be two (2) digits.
01 = January 02 = February 03 = March 04 = April
05 = May 06 = June...
User's Manual - Page 23
...RESERVED
NX1448E Icon Keypad
Page 23 It is tampered, the tamper icon will flash and the zone icon(s) will be "on ", press [r]-[2] to the system fault(s) below:
1 Over ...and the zone icon(s) will be on .
ICON 1
2
PROBLEM
SYSTEM FAULT - If a zone(s) is "on " if the security system requires service. SETTING THE KEYPAD LIGHTING
Step 1 Press [r]-[9]-[1]. If a zone(s) is usually...
User's Manual - Page 24
...
6
TELEPHONE LINE TROUBLE/LINE CUT - Press [#] key to
return to Icons 6,7,8: This fault is entered. * SEE NOTE AT END OF TABLE.
7
FAILURE TO COMMUNICATE - Press the [6] key. Press the [4] key and the zone
icon(s) will
illuminate showing which zone(s) has loss of power and your system and the
central station. * SEE NOTE AT...
User's Manual - Page 25
...Chime" feature.
Pulses when a FIRE zone has a trouble condition.
Beeps to silence a pulsing keypad sounder. Entering a code will not change when entering a code to indicate Telephone Line Cut, if selected. The arm/disarm state of the following conditions are bypassed.
Pulses when the armed status changes and any of your installer if a trouble condition exists. Pulses...
Similar Questions
Change Security Code For: Ge Networx With Nx-1448e Keypad
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
(Posted by Jim39164 8 years ago)
Will This Keypad Work With A Simon 3 Panel ?.
(Posted by Anonymous-70543 11 years ago)
Change Master Code
How do I change the alarm disarm code on my ge nx 1448e
How do I change the alarm disarm code on my ge nx 1448e
(Posted by rtbairddds 13 years ago)
Hi. I Have A Ge Simon 3 Security System. It Has Not Been In Use For 1.5 Years.
I have recently hooked the system up with monitoring. Both of my touchpad remotes do not work. I cha...
I have recently hooked the system up with monitoring. Both of my touchpad remotes do not work. I cha...
(Posted by tasimard 13 years ago)