GE 60-806-95R-16Z Support Question
GE 60-806-95R-16Z Support Question
Find answers below for this question about GE 60-806-95R-16Z - Security Concord Express System Control Panel.Need a GE 60-806-95R-16Z manual? We have 1 online manual for this item!
Question posted by clctakumoh on June 3rd, 2014
How To Change Battery In Concord Express Alarm
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TechSupport101 on June 3rd, 2014 4:30 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,325
Member since:
May 24th, 2013 Points: 12,171,325
Hi. See page 58 of the Installation Instructions here http://www.helpowl.com/manuals/GE/6080695R16Z/52816
Related GE 60-806-95R-16Z Manual Pages
Installation Instructions - Page 1
) *( 6HFXULW\
ZZZ*(6HFXULW\FRP Part No: 60-806 60-806-95R
466-1665 Rev G June 2004
T e s t S y s te m W e e k ly
O ff
A
1
p re s s b o th N...s
D
*
S ta y 2
S ile n t 5
S y s te m 8
L ig h ts 0
A rm e d R eady
A w ay 3
6 M enu
9 B ypass
#
Concord Express
Installation Instructions p ress 2 fo r O N ; P ress 1 fo r O F F ;
Z o n e/Sen so r N u m b er
01 02 03 04 05 06 07
B yp a...
Installation Instructions - Page 6
...Control Panel (60-806, 60-806-95R) • Backup Battery, 12 VDC, 4 AH (60-681) • SuperBus 2000 2x16 LCD Touchpad (60-746-01), SuperBus 2000 Fixed Display
Touchpad (60-820), SuperBus 2000 2x20 LCD Touchpad (60-803), or SuperBus 2000 2x20 VFD Touchpad (60...and configuration listings. This security system can be used as a wire warning system, an intrusion alarm system, an emergency notification...
Installation Instructions - Page 9
... • Connecting Touchpads • Installing an RJ-31X Phone Jack • Connecting the Phone Line to install the system control panel. Displays system messages and indicates system status. Installing the System
Installing the System
• Bus A and B: Input and output...inputs, of the following describes the different touchpads that can be used for a list of GE Security 319.5 MHz.
Installation Instructions - Page 13
... (60-774) adds eight supervised hardwire zones to module inputs (see Figure 8).
Connect all necessary input/output wiring using the installation instructions included with the HIM. Both normally open and normally closed detectors can be wired to the system.
Installing the System
8 Push SnapCard Connector Onto Panel Header
Secure SnapCard with the Concord™ Express panel...
Installation Instructions - Page 14
... 9
10
11
Normally Closed (N/C) Contacts in Series
Normally Open (N/O)
Contacts in the Concord Express
G N D +12V
3
4
A BUS B
5
6
Panel Terminals
Connecting Detection Devices to Panel Zone Inputs
The panel comes with panel) at the last device on the circuit. The minimum available panel voltage for hardwired PIR motion detectors is 300 ohms, plus the 2k end-of-line (EOL...
Installation Instructions - Page 17
...Number 01500 for UL Listed systems) if the backup battery is programmed to Reset After Canceling a Fire Alarm
CC OONN
+. +. .- .- At the default ...changing the output configuration number.
+12V
4
2k Ohm EOL Resistor
(49-454) Locate at Last Device
Model 449AT
Note Install all sirens/speakers indoors, in Appendix A. M. Black (Common)
Yellow (Steady)
GND
Concord Express Panel...
Installation Instructions - Page 18
...to the manufacturer's documentation for UL Listed systems) if the backup battery is connected.
or 8-ohm speaker loads) • ATW Models ... default setting (01710) activates the output for status and alarm tones, which allows for use with a 2k end-of...connection without changing the output configuration number. Only one black wire and one 15-Watt, Dual-Tone Siren to panel ground (...
Installation Instructions - Page 22
... unplug the transformer and disconnect the backup battery. Hold the outlet cover in programming mode. Make sure the system is completed, simply disconnect the touchpad from the Programming Touchpad Cable (60-
791) to the outlet cover.
! Warning
Use extreme caution when securing the transformer to the panel terminals:
1.
Connecting a Programming Touchpad
4. Press 8 + 4321 + 0 + 0 and...
Installation Instructions - Page 26
... appears.
2. ber.
Account Number (0010)
Security-Partition 1 (Default = 00000)
The account number is used as panel (or customer) identification for users if this setting...Security-Global (Default = none)
The 4-digit dealer code is used to prevent unauthorized persons from Level 2STAY to be controlled by the SIA False Alarm Reduction Standard:
• Arming level changes...
Installation Instructions - Page 29
... 2=off)
When this setting is on, the panel reports to the central station events that involve a high-level security risk, including the following conditions: • Force Armed • Hardwire Zone Trouble (open or short) • Supervisory (wireless devices) • Low Battery (wireless devices) • Other non-alarm related conditions
¾ To turn Opening/Closing...
Installation Instructions - Page 30
...high-level security risk, including the following conditions: • Force Armed • Hardwire Zone Trouble (open or short) • Supervisory (wireless devices) • Low Battery (wireless ... LOW LEVEL RPTS OFF/ON (new setting).
• Other non-alarm related conditions
25
Programming the Panel nication to panel commu- The display flashes the entered setting.
2. Phone Number (0120...
Installation Instructions - Page 38
... setting), press 1 (off or on , only arming level changes are restored (after an extended power outage). Reporting-Global (Default=off)
¾ To turn Buffer Control off or on , the panel reports to the central sta- ¾ To turn Battery Restoral reports off ) or 2 (on , the panel reports to the central station when AC and backup...
Installation Instructions - Page 39
... the panel event buffer (memory) is also on and a second sensor trip does not occur within a 4- (on). Note As with all GE Security panels, hardwire smoke detectors connected to 503 with the "Alarm Verify"... alarms report using a 3-digit code from 500 to Concord or SnapCard hardwire zones do not send restorals.
¾ To turn AC Failure reports off )
When this setting is on , the panel ...
Installation Instructions - Page 40
...determines whether the panel reports to the central monitoring station (or pager) daily or weekly when a wireless device reports a low battery condition to the panel.
¾ ...panel automatically bypasses a sensor or zone after it .
When set to 2, the panel waits until a sensor or zone has caused a second alarm (during a single arming period) before bypassing it causes an alarm. Changing...
Installation Instructions - Page 46
...setting. 3. Remove AC and battery power from the panel. 5. Apply AC and battery power to select the desired ...output 3) (081030-output 4)
Acc.
Press A or B to the panel. Press ƒ and the display shows the new setting. Modules-Bus Devices (Default=none)
¾ To change a bus device ID number when replacing a defective bus device. The ...alarm, open sensor, or arming the system.
Installation Instructions - Page 57
...battery. Reverse the phone wires connected to SnapCard or onboard (panel) outputs 1 and/or 2 don't produce any alarm sounds.
1. correct where necessary. 2. If the charging voltage is running a backup battery.... 4.
Check for proper panel and transformer wiring.
3. Check for 11.75 to operate from backup battery.)
1. Warning
Be careful when securing the transformer to 13.5 ...
Installation Instructions - Page 58
... sensor is not tested after replacing the battery. Change mounting position of panel cabinet.
2. Verify that sensor is installed up into panel memory. Touchpad is too far away. Replace the indicated device battery. Testing the sensor/touchpad with good battery information. Use an RF Sniffer (60-401) to clear the condition.
2. Secure sensor mounting and/or cover, then...
Installation Instructions - Page 59
...60-820
SuperBus 2000 Fixed Display Touchpad
33 mA
60-803-04 SuperBus 2000 2x20 LCD Alphanumeric Touchpad
75 mA
60-804-04 SuperBus 2000 2x20 VFD Alphanumeric Touchpad
75 mA
60-774
SuperBus 2000 Hardwire Input Module
18 mA
SnapCards (1 per panel)
60... device must be subtracted from the UL allowed alarm load of 650 mA (panel terminal 7-OUT1/+12)
Appendix A: System Configuration Worksheets...
Installation Instructions - Page 73
...Alarm control annunciating alarm level changes on , Silent Arming is forced to off and is annunciated on all factory programmed zones. If SIA False Alarm is on, the arming level is not available in user programming. Install an end-of 4 bus devices (0 - 3). SIA False Alarm • SIA False Alarm (0003) option has been added to control access to Security... 09110
*The panel comes with six...
Installation Instructions - Page 74
...previous release, an alarm that supports the panel's specific OEM code.
onds. These panels can now be reported to 60 seconds. This ...alarm, the system now displays all the alarms that an alarm report to 30 seconds. RF smoke detectors repeat the alarm transmission every 60 seconds as long as hardwire smokes. In previous releases it for Dialer Abort Delay (02006) has been changed...
Similar Questions
Concord Express Part No. 60-806 95r Clear Panel Memory
Cant find the code to clear panel memory to remove fault codes
Cant find the code to clear panel memory to remove fault codes
(Posted by redneckstill 10 years ago)
How To Change Battery In Carbon Monoxide Alarm 240 Coe
(Posted by alandave 10 years ago)
How Do I Change Battery? Ge 60-511-02-95 - Iti Wireless Ds924i Pet Immune Pir.
HOw do I change the battery in GE 60-511-02-95 - ITI Wireless DS924i Pet Immune PIR.
HOw do I change the battery in GE 60-511-02-95 - ITI Wireless DS924i Pet Immune PIR.
(Posted by robindonohue 13 years ago)
Security System 60-806-95r-16z
How can I permantly delete a sensor? Sayssensor 08 is not operating, but I only have 7 sensors.
How can I permantly delete a sensor? Sayssensor 08 is not operating, but I only have 7 sensors.
(Posted by lewann105 13 years ago)