2010 GMC Yukon Support Question
2010 GMC Yukon Support Question
Find answers below for this question about 2010 GMC Yukon.Need a 2010 GMC Yukon manual? We have 1 online manual for this item!
Question posted by mammydpb on September 25th, 2016
Steps For Turning Off The Mirrors Going Down In Reverse
What Sequence Of Buttond To Push
Current Answers
Answer #1: Posted by zzed41 on September 25th, 2016 9:29 AM
zzed41
Member since:
December 12th, 2014 Points: 914,010
Member since:
December 12th, 2014 Points: 914,010
Press the customization button until PARK TILT MIRRORS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Then press the customization button to scroll through the following settings:
OFF (default): Neither outside mirror will be tilted down when the vehicle is shifted into R (Reverse).
DRIVER MIRROR: The driver's outside mirror will be tilted down when the vehicle is shifted into R (Reverse).
PASSENGER MIRROR: The passenger's outside mirror will be tilted down when the vehicle is shifted into R (Reverse).
BOTH MIRRORS: The driver's and passenger's outside mirrors will be tilted down when the vehicle is shifted into R (Reverse).
NO CHANGE: No change will be made to this feature. The current setting will remain.
Hope this helps! If it does, please click on the Accept Answer button. I will greatly appreciate it! :)
Related Manual Pages
Owner's Manual - Page 8
... the START position or a remote vehicle start , the engine may Auto Start at a fuel efficient point. After a successful engine start is not running , but may turn off until you would any time without notice. When the tachometer needle indicates AUTO STOP, the hybrid system is not running and will be improved...
Owner's Manual - Page 9
...and Indicators and Driver Information Center (DIC) in the Two‐Mode Hybrid supplement to push and the stopping distance may occasionally hear the motor driven pump when it recharges the system...also has an EV mode which uses only the electric motor to insure effective braking. Always turn the ignition switch to run.
EV mode is unavailable when the vehicle is called Auto ...
Owner's Manual - Page 18
...the hybrid drive motor may enter Auto Stop after a remote vehicle start , the engine may turn the ignition switch to move. When the tachometer needle indicates OFF, the engine is not running ... is at an acceptable state of the vehicle conditions that the ignition switch is in P (Park), R (Reverse), N (Neutral) or D (Drive). In very hot conditions, Auto Stop may Auto Start at any time...
Owner's Manual - Page 22
...or M (Manual Mode) can be more noticeable with a cold transmission. If you need more , push the accelerator all the way down . You may be a delayed shift, however the transmission is operating... This position is normal.
3-8 Going less than about 35 mph (55 km/h), push the accelerator pedal about 35 mph (55 km/h) or more power for off-road driving. Going about halfway down . M (...
Owner's Manual - Page 28
...(Neutral) by shifting the transmission to R (Reverse) for one shift per 10 seconds. Set the parking brake and apply the regular brake pedal. 2. Turn the ignition to ON/RUN with the engine off... out of N (Neutral), the N (Neutral) light will turn the engine off , and shift the transmission to ACC/ACCESSORY, which will go out.
3-14 Turn the ignition to N (Neutral). 3. 7. Release the parking ...
Owner's Manual - Page 29
... pulling a trailer, see Towing a Trailer on fairly level ground, use the steps that follow. If you . So, be free to roll, even if the...
3-15 You or others could be dangerous to LOCK/OFF. 5. Turn the ignition key to get out of the Owner Manual for more ...transfer case is not fully in N (Neutral), the vehicle will go. 3. Shifting Into Park
1. Move the shift lever into the ...
Owner's Manual - Page 32
... or others can be seriously injured. Follow the proper steps to insure effective braking, such as when a high braking... Running the Vehicle While Parked
It is better not to push and the stopping distance may occasionally hear the motor driven pump... at any requirements for deceleration. Shift to P (Park) and turn the ignition to a complete stop. Because the vehicle has the Automatic...
Owner's Manual - Page 36
It should go out once the engine has been started. United States Version shown, Canada similar When the gas engine is off and... ON/RUN position, the position of the tachometer indicator shows the state of the vehicle:
.
If a short distance must be certain to turn off all the accessories.
.
Have the vehicle serviced by an Auto Start, at any time. See DIC Warnings and Messages on , be...
Owner's Manual - Page 38
...States
Canada
4-6 If one part is still on and a chime sounds there could be harder to push or can go closer to ON/RUN. This light should come on can still work and stop . If the ...stopped, have the vehicle towed for service. If the vehicle is set. The vehicle's hydraulic brake system is turned to the floor. This light also comes on page 5‑2. If it will be ready to warn if...
Owner's Manual - Page 43
... shows approximately how much fuel is left in the tank. The gage does not go back to E (empty) when the ignition is turned off before it is on .
At the gas station, the fuel pump shuts ... on the fuel gage indicates the side of these indicate a problem:
.
The gage moves a little while turning a corner or speed up than half the tank's capacity to fill up . The gage will first indicate ...
Owner's Manual - Page 74
... to jump start your vehicle.
6-18 Only use another vehicle and some or all of these steps could damage the vehicle. 1. If the vehicle's 12‐volt battery has run down, you...follow these steps exactly, some jumper cables to start the vehicle by the warranty. Trying to start your vehicle. They contain enough electricity to the vehicle can be covered by pushing or pulling ...
Owner's Manual - Page 78
Now connect the black negative (−) cable to the dead battery. The other end of the negative (−) cable does not go to the negative (−) terminal of the good battery. Connect the other end touch metal. If it will not start the vehicle with ... negative (−) cable to start the vehicle that the cables do not touch each other or other end touch anything until the next step.
Owner's Manual - Page 88
...driver side front tire. 5. Set the parking brake. 2. Proceed to the tire/wheel positions in Step 5. 7. The sensors are matched to the passenger side rear tire, and repeat the procedure in... displays on the Remote Keyless Entry (RKE) transmitter at the same time for approximately five seconds. Turn the ignition switch to signal the receiver is outlined below: 1. Press Q and K on the ...
Owner's Manual - Page 89
Proceed to 13 000 km). Turn the ignition switch to the driver side rear tire, and the TPMS sensor matching process is no longer active. See "Loading Your Vehicle" in Step 5. The Tire Pressure Monitor System (TPMS) sensors will need to be rotated every 5,000 to 8,000 miles (8 000 to the driver side...
Owner's Manual - Page 95
... (O) position. 2. The pressure gage (E) will initially show a high pressure while the compressor pushes the sealant into the tire, the pressure will quickly drop and start to rise again as ...has an accessory power outlet, do a safety check first. Once the sealant is tight.
6. Turn it clockwise until it counterclockwise. 5. See Tire Sealant and Compressor Kit Storage on the ground. ...
Owner's Manual - Page 96
...The compressor may read higher than the actual tire pressure while the compressor is reached. Turn the compressor off button (D) to the recommended inflation pressure using the pressure gage (E). Be...the accessory power outlet in the tire, therefore, Steps 11 through 17 must be driven farther. The pressure gage (E) may be turned on the Tire and Loading Information label. Press ...
Owner's Manual - Page 101
... the vehicle has the tire sealant and compressor kit shown above, see the operating instructions that follow.
6-45 Push the air compressor inflator hose (F) onto the sealant canister inlet and push the lever down and turn it in the air compressor. 2. Align the sealant/air hose (F) with the slot in its original location...
Owner's Manual - Page 105
... the air compressor. 8. The pressure gage (C) will initially show a high pressure while the compressor pushes the sealant into the accessory power outlet in the door or window. 7. Remove the tire sealant and...kit on page 6‑55. 2. Remove the valve stem cap from the flat tire by turning it is completely dispersed into the tire, the pressure will inject sealant and air into the tire...
Owner's Manual - Page 106
...pressure while the compressor is reached. See "Roadside Assistance Program" in the tire, therefore, Steps 12 through 18 must be warm after usage. 12. The tire is not sealed and will...gage (C). The pressure gage (C) may be driven farther. Turn the compressor off . Notice: If the recommended pressure cannot be reached after Step 11. Remove the power plug from the accessory power outlet...
Owner's Manual - Page 112
To store the tire sealant and compressor kit, reverse the steps.
6-56 Appearance Care
Vehicle Care/Appearance Materials
When scraping the windshield glass to release the unit. 4. Remove the sealant and compressor kit with a selector switch ...
Similar Questions
Door Mirror
how do you take inside door panel off trying to replace passenger side door mirror
how do you take inside door panel off trying to replace passenger side door mirror
(Posted by Roaddog01 8 years ago)
How Do I Turn The Key Back In A Yukon Without The Radio Going Off
(Posted by clatyrone 9 years ago)
Side Mirror Fog
The driver side mirror is leaking something and fogging up.
The driver side mirror is leaking something and fogging up.
(Posted by Anonymous-98104 11 years ago)
How Do You Keep The Passenger Side Mirror From 'drifting'?
The passenger side mirror needs to be reset everyday! Is there a way to set it so that it does not "...
The passenger side mirror needs to be reset everyday! Is there a way to set it so that it does not "...
(Posted by kdunn 12 years ago)