Dewalt DW744XRS Support Question

Find answers below for this question about Dewalt DW744XRS.
Need a Dewalt DW744XRS manual? We have 3 online manuals for this item!

Dewalt Overview Questions Manuals Reviews Videos Research

Question posted by etwphonehome on August 29th, 2015

Dw9062 9.6 Volt Battery For Cordless Drill

I have been able to find a DW9061 replacement battery but not the DW9062. Are these batteries interchageable?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on August 29th, 2015 5:08 PM

This answer was accepted by the poster of the original question.

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,407

1,100
points

Yes, but can go here for the oem dw9062 battery.

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Dewalt DW744XRS Manual Pages

Instruction Manual - Page 2

...LONG HAIR • KEEP HANDS AND FINGERS OUT OF THE SAW BLADE PATH - Every tool is produced with painstak- from drills to sanders to make sure that it meets your standards for America's tough- ing ... HAS STOPPED • DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS • SECURE TOOL PROPERLY TO PREVENT UNEXPECTED MOVEMENT • DO NOT OPERATE THIS MACHINE WHILE UNDER THE INFLUENCE OF ...

Instruction Manual - Page 3

...VOLTS If the machine is intended for use extension cords without yellow stripes is of power tools in damp or wet locations or in rain can result in death or serious injury. Repair or replace...resistance for added protection against injury resulting from spindle before operating product. Repair or replace damaged or worn cord immediately. A temporary adapter, which , if not avoided...

Instruction Manual - Page 4

... of balance may cover moving parts. Damaged parts can be properly repaired or replaced. Don't leave tool until it can cause further damage to contain long hair. Always remember that ...HANDS AND FINGERS AWAY from frequent use of your saw) TO REPLACE SAFETY RULES. MINIMUM GAGE FOR CORD SETS Volts Total Length of the tool, a guard or other jewelry to get caught in loss of...

Instruction Manual - Page 5

... making rabbets and other than 2" (51 mm) wide, you must prevent the wood from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Push the work , 6" ... of the saw blade and effectively fights kickback by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to the ...

Instruction Manual - Page 6

...specially designed to the power source 4 until the machine is completely assembled and you do this tool can cause injury. 4 5 2 3 Carefully unpack the table saw base) 4. Miter gauge..., drilling, and other construction activities. If any adjustments. The following sections on how often you read and understand the entire instruction manual. To reduce your dealer to replace them...

Instruction Manual - Page 7

Throat plate Tools needed for assembly include a screwdriver and the wrenches included with the opening on fence rails, ...Be sure to snap both latches in Figure 6. Using the arbor wrench, tighten the arbor nut by turning counterclockwise. 3. ATTACHING/REPLACING THE BLADE 1. Ensure the spindle and washers are against the inner washer and the large washer diameters are free from the saw ...

Instruction Manual - Page 9

...rotate it down to turn to be mounted firmly. Center the saw and drill 1/4" (6.4mm) holes in the places you drilled in . Remove the saw on the front of injury, before adjusting ... the plywood and insert four 1/4" (6.4mm) machine screws FROM THE BOTTOM. All DEWALT tools are available from power source before installing and removing accessories, before connecting saw table. Rip...

Instruction Manual - Page 13

... out. Maximum dado width on plastic parts. never immerse any liquid get inside the tool; The height adjustment screw may seriously damage plastic parts. Miter Gauge Operation To set ...are not through cuts, the cuts must be performed with one pass. See Figure 26. Replace it with the blade guard removed. DO NOT USE WIDER COMBINATIONS. Dust Collection Your table ...

Instruction Manual - Page 14

... height adjustment screws threads on its side, so the bottom, open part of purchase with this product, use identical replacement parts. If you can return it within 90 days from your DEWALT Power Tool, Laser, or Nailer for a full refund - To reduce the risk of warranty coverage and warranty repair information, visit...

Instruction Manual - Page 44

...fence. Trou de suspension optionnel. Encoche pour empêcher la main de glisser. DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 (DEC06) Form No. 647535-00 DW744, ... © 2002, 2004, 2006 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; PRECAUCIÓN: fabrique varas de empuje de madera contrachapada o...

Instruction Manual - STAND - Page 3

... mechanisms are in death or serious injury. It is approved for use with table saws only. Tools Required Phillips screwdriver Socket or wrench set Contents Stand Carriage head bolts (2) Mounting brackets (2) M8 ...the risk of personal injury: • ALWAYS use only identical replacement parts. If you experience a problem with Folding Legs WARNING: For your DEWALT purchase, please ...

Instruction Manual - STAND - Page 4

...Attach the axle (A) to be stored in the kickstand tube before inserting the tube plugs. Fasten the tool to the beams (I) with the legs folded and stand sitting on the ground. DO NOT use the...nuts as shown for which it is designed to the leg support (B) by aligning the pre-drilled holes. Ensure the long end of the axle is an upright position. Attaching the Kickstand ...

Instruction Manual - STAND - Page 5

... the stand upright. If the saw is mounted properly, the mounting brackets will be positioned perpendicular to the table saw is fully anchored on the tool mount so that the locking pins have engaged and the legs E are equipped with a flat washer, lock washer and nut provided. WARNING: For your own...

Instruction Manual - STAND - Page 7

...pins have not been tested with this product, use identical replacement parts. 6 Pull out the remaining two legs. Repeat with this tool could be performed by DEWALT, have engaged and the legs ... repairs, maintenance and adjustments should be hazardous. K L M F 3. To Raise Stand from your tool are firmly held in place. If you work. 5. Pull the handle lock down to the workspace. ...

Instruction Manual - STAND - Page 8

... warranty does not apply to faulty materials or workmanship for a free replacement. 7 FREE WARNING LABEL REPLACEMENT: If your DEWALT Power Tool, Laser, or Nailer for any reason, you are covered by our...433-9258). This warranty does not cover part failure due to the warranty, DEWALT tools are not completely satisfied with a receipt for warranty information. For further detail of purchase...

Instruction Manual - STAND - Page 24

...) Part No. 648674-00 DW7440RS Copyright © 2007, 2008 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the "D" shaped air intake grill; the array of the tool. and the array of lozenge-shaped humps on the surface of pyramids on the handgrip;