Dewalt D28065 Support Question
Dewalt D28065 Support Question
Find answers below for this question about Dewalt D28065.Need a Dewalt D28065 manual? We have 1 online manual for this item!
Current Answers
Related Dewalt D28065 Manual Pages
Instruction Manual - Page 3
... reduces the risk of electric shock.
Read all safety warnings and all instructions. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). DANGER: Indicates an imminently hazardous situation which , if not avoided, may result in any adapter...
Instruction Manual - Page 4
... personal injury. Do not use a ground fault circuit interrupter (GFCI) protected supply. b) Use personal protective equipment. c) Prevent unintentional starting the power tool accidentally. Ensure the switch is maintained.
2 Carrying power tools with your finger on invites accidents. A wrench or a key left attached to control. e) Do not overreach. Keep proper footing and balance...
Instruction Manual - Page 5
... not use inspect the accessory such as a grinder, sander, wire brush, polisher or cut-off tool.
Accessories running faster than their rated speed can be capable of the power tool. d) The outside diameter and the thickness of your power tool. Accessories with this test time. If power tool or accessory is dropped, inspect for Grinding, Sanding...
Instruction Manual - Page 6
...working corners, sharp edges etc.
Abrasive wheels may grab the surface and pull the power tool out of snagging. b) Never place your clothing, pulling the accessory into the spinning accessory....spinning accessory could ignite clothing.
4
Using water or other accessory.
l) Do not run the power tool while carrying it at the point of the wheel that are unsafe. Avoid bouncing...
Instruction Manual - Page 7
... to shatter.
The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. Follow manufacturers recommendations, when selecting sanding paper. English... wheel pinching and kickback.
Safety Warnings Specific for the higher speed of a smaller tool and may cause snagging, tearing of cut -off wheel. Additional Safety Warnings Specific ...
Instruction Manual - Page 8
... number of the wire, the greater the capacity of the cable, that may result.
• Do not operate this occurs, stop the tool and inspect the wheel for Grinders
WARNING: The grinding wheel or accessory may cause permanent injury to fingers, hands, and arms. Use gloves to make up the total length...
Instruction Manual - Page 9
... contains chemicals known to these exposures varies, depending on how often you do this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other... eyeglasses are specially designed to cause cancer, birth defects or other injury. To reduce your tool may promote absorption of work with approved safety equipment, such as follows:
V volts
A ...
Instruction Manual - Page 10
...)
INTENDED USE
The D28065, D26065N, D28115, D28115N heavy-duty angle grinders have been designed for professional grinding at various work sites (i.e., construction sites). DO NOT let children come into contact with the tool. Spindle Lock Button D. Yellow Rubber Ring
G1. These heavy-duty angle grinders are professional power tools. DO NOT use this tool.
An accidental...
Instruction Manual - Page 11
....
9
FIG. 2
I ) can be fitted to motor
housing. 3. Separating the gear case from tool. 2. Remove guard and flanges from motor housing not more than 1/4"
(6.35 mm), rotate the gear case...wheel
Type 27 depressed center wheel
threaded clamp nut
Rotating the Gear Case
1. Before using the tool, check that the handle is tightened securely. Remove the four corner screws attaching the gear case...
Instruction Manual - Page 13
... mm) arbor hole. Grinding and cutting with wheels other accessories running over rated accessory speed may be serviced and re-assembled by ... discs. Overtightening could cause screws to have the tool serviced may have a 5/8"-11 hub. Threaded accessories.... 4. Mounting instructions for these accessory guards are provided with grinder accessories. English
(114.3 mm) and 5" (127 mm)...
Instruction Manual - Page 14
... may burst and cause injury. Close the guard latch to run up on or off . Do not operate the grinder with the clamp lever
in open the guard latch, rotate the guard so
that the tool is pre-adjusted to stop before turning the tool off.
OPERATION
WARNING: To reduce the risk of the...
Instruction Manual - Page 15
... lock-on the spindle by hand.
3. Do not engage the spindle lock while the tool is operating because damage to the tool will run after any interruption in damage to stop . Depress the spindle lock button and use with D28065 G1, G2
and D28065N for Type 27 grinding wheels
only.
Depress and release the...
Instruction Manual - Page 16
...
high speed. The
open - Apply minimum pressure to operate at high speed. Once a cut -off work surface, allowing the tool to the work surface before touching the tool to 30˚ angle between the tool and work surface.
FIG. 8 1/4" wheels (6.35 mm)
threaded clamp nut
Quick-Change backing flange 1/8" wheels
(3.17 mm)
SURFACE GRINDING...
Instruction Manual - Page 17
Wheel breakage and injury may result. Maintain a 5˚ to avoid creating gouges in various grits. FIG. 11
4. Continuously move the tool in a
forward and backward motion to 10˚ angle between the tool and work surface.
2. Place or appropriately thread backing pad (O) on the backing pad.
3. Tighten the clamp nut by hand.
Finer grits...
Instruction Manual - Page 18
...tool to 10˚ angle between the edge of the wheel and the work surface.
2.
USING WIRE CUP BRUSHES AND WIRE WHEELS
(FIG. 14, 15)
Wire wheels and brushes can become sharp. Maintain contact between the tool and work surface for smoothing irregular surfaces.
1. A Type 27 guard is greatest when the tool... on the grinder spindle without moving, or moving the tool in a circular...
Instruction Manual - Page 19
...1) Wheels (Fig. 1)
Cutting wheels include diamond wheels and abrasive discs. Do not operate grinder with tool) must be used for metal and concrete use the quick-change backing flange, centering the...tighten clamp nut with the
slots (L) on the raised section (pilot). 3. NOTE: All grinders that the arrows are not designed for side pressures encountered with
clamp lever in closed ,...
Instruction Manual - Page 20
... recommended accessories should be hazardous. Cutting rate is required under the Federal Consumer Safety Act. Changing the angle will help you obtain more efficient warranty service in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our...
Instruction Manual - Page 21
... for warranty information.
For products sold in Latin America. In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will repair, without charge, any time during... contained in certain states or provinces. This warranty does not apply to normal wear or tool abuse. This warranty does not cover part failure due to accessories or damage caused where ...
Instruction Manual - Page 72
...., 701 East Joppa Road, Baltimore, MD 21286 (OCT12) Part No. N234380 D28065, D28065N, D28115, D28115N Copyright © 2007, 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box...
Similar Questions
Dwe43244n Problems
my grinder shuts off after 3 or 4 seconds. I can unplug and plug it back in but it does the same thi...
my grinder shuts off after 3 or 4 seconds. I can unplug and plug it back in but it does the same thi...
(Posted by rkba1911 4 months ago)
Will Not Build Over 30 Lb. Never Quit Running
Will not build over 30 lb. Of pressure keeps running
Will not build over 30 lb. Of pressure keeps running
(Posted by thomasdavis359 6 years ago)
9' Right Angle Grinder Dwe 4519
I am wondering if it is possible you can give me a torque value for this grinder? it is 120 V 15 A a...
I am wondering if it is possible you can give me a torque value for this grinder? it is 120 V 15 A a...
(Posted by angelcoleman 9 years ago)
Dewalt Dw758 Grinder Wiring
I have a Dewalt DW758 grinder that the hot wire burnt up to the switch. Am replacing wiring need to ...
I have a Dewalt DW758 grinder that the hot wire burnt up to the switch. Am replacing wiring need to ...
(Posted by flojo2 10 years ago)