Cub Cadet GTX 1054 Support Question
Cub Cadet GTX 1054 Support Question
Find answers below for this question about Cub Cadet GTX 1054.Need a Cub Cadet GTX 1054 manual? We have 3 online manuals for this item!
Question posted by bpouget on October 28th, 2013
Engine Shuts Off When Pto Is Engaged
The engine starts and runs fine with throttle in fast mode. When the PTO is engaged, the engine shuts off. Nothing in manual troubleshooting contemplates this problem. Suggestions?
Current Answers
Related Cub Cadet GTX 1054 Manual Pages
Series 1000 Brochure - Page 1
... LGT 1054 LGTX 1050 LGTX 1054 GTX 1054
Designed for all -day comfort. The product depictions are subject to change oil service minder, battery voltage monitor, park brake and PTO start sequence LEDs
Neutral start, operator presence, reverse safety switch, brake pedal lock, RevTEK™ reverse mowing technology
OPERATION PTO Clutch Deck Lift Brakes Seat
Electronic fingertip engagement for...
Series 1000 Brochure - Page 2
...PTO start sequence LEDs
Neutral start , operator presence, reverse safety switch, brake pedal lock, RevTEK™ reverse mowing technology
OPERATION
PTO Clutch
Deck Lift Brakes Seat
Manual lever control Manual/12-position
Electronic fingertip engagement...
SERIES 1000
LAWN AND GARDEN TRACTORS
ENGINE
Engine Type
Cylinders/Material Lubrication
DRIVE SYSTEM
Drive System
Engine to Transmission ...
GTX 1054 Operator's Manual - Page 1
... 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-08379 (December 18, 2012) Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Hydrostatic Garden Tractor - GT 1054, GTX 1054
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS...
GTX 1054 Operator's Manual - Page 4
... lawn roller, etc.) on slopes greater than 15 degrees as part of riding mower... the riding mower safely enough to start engine.
1. Muffler and engine become hot ...manually on
hazard.
Rapid engagement or braking could result in severe injury or death.
unusually tall, dry grass (e.g., pasture) or piles of engine...cause a burn. Never leave a running machine unattended. Do not touch.
...
GTX 1054 Operator's Manual - Page 5
... or running engines. Section 2 -
e. If equipped, the "Reverse Caution Mode" should... manual ...prevent unintended starting the engine. a....Engine exhaust contains carbon monoxide, an odorless, and deadly gas.
2. Never carry children, even with the blade(s) shut...mower). j. c. "zero-turn machine off the engine and equipment. When practical, remove gas-powered equipment from hot or running...
GTX 1054 Operator's Manual - Page 9
...• One Garden Tractor • One Garden Tractor Operator's
Manual
• One Oil Drain Tube • One Engine Operator's Manual
• One Deck Wash Hose Coupler • One Product ...will NOT engage when the hydrostatic bypass rod is necessary to operate the riding mower without first opening the hydrostatic relief valve. WARNING! Failure to move the tractor manually without ...
GTX 1054 Operator's Manual - Page 12
...section of the seat. Failure to comply with the cutting deck engaged, be certain that are illustrated in the FAST (rabbit) position. NOTE: The brake pedal must be used for...this manual, including the entire Operation section, before attempting to aft position of the engine and, when pushed all safety rules and instructions in a given position, the throttle will maintain a uniform engine ...
GTX 1054 Operator's Manual - Page 13
... cause the tractor to its original position when it 's not pressed. The pedal will travel.
PTO (Blade Engage)
If the PTO light illuminates when attempting to start the engine, insert the key into the disengaged (OFF) position. To use, move PTO lever into the ignition switch and turn the ignition key counterclockwise to illuminate while the...
GTX 1054 Operator's Manual - Page 14
... with the engine running machine unattended.
PTO / Blade Engage Knob
Activating the PTO engages power to the cutting deck or other (separately available) attachments.
Pull outward on the left side of the tractor's dash and indicates the amount of this manual for detailed instructions regarding the parking brake. Located in the disengaged (OFF) position when starting .
14
Section...
GTX 1054 Operator's Manual - Page 15
... run poorly. Remove the key from the ignition switch to the Assembly & Set-Up section of this manual for your safety and protection. WARNING! NOTE: Refer to prevent unintended starting unless the parking brake is engaged, and the PTO (Blade Engage) knob is engaged.
• With the ignition key in the START position for any damage. Contact your engine...
GTX 1054 Operator's Manual - Page 16
... (PTO) engaged.
Start Position
Figure 5-2 3. The red indicator light at the top, left or right. Reverse Caution Mode
The REVERSE CAUTION MODE position of the key switch module allows the tractor to be driven in REVERSE, check that the area behind is clear then slowly depress the lower portion of the drive pedal with the engine running...
GTX 1054 Operator's Manual - Page 17
... 4 to engage the parking brake. Never leave a running or the engine will automatically ...shut off. To disengage the parking brake, lightly press the brake pedal . Release pressure from the parking brake/cruise control lever. WARNING! Always disengage PTO...engaged, press the brake pedal to disengage the cruise control and bring the tractor to prevent unintended starting.
Engaging...
GTX 1054 Operator's Manual - Page 18
...cutting. Move the throttle control lever to mow lawns, NOT clear brush.
• Keep the blades sharp and replace the blades when worn.
18
Section 5 -
Engaging the PTO
Engaging the PTO transfers power to the... yellows quickly in dry weather.
• Always operate the tractor with the throttle lever in the FAST (rabbit) position while mowing
• For best results it is recommended that...
GTX 1054 Operator's Manual - Page 19
Engine
Refer to the Engine Owner's Manual for a few minutes to allow the oil in the crankcase to the skin.
If the engine has been recently run, the engine...engine sediment which are being done at every oil change , proceed as follows:
1. Changing the Engine...engine.
19 Run the engine for all engine maintenance procedures...starting.
Before performing any engine repair establishment or individual. NOTE...
GTX 1054 Operator's Manual - Page 20
...'s Manual.
Drive the tractor to expose the drain port. Re-cap the end of the hose into an appropriate oil collection container with the tabbed drain go to reach. Disengage the PTO (Blade Engage), set the parking brake and stop the engine.
2....keep debris from entering the drain port.
8. Pop open the protective cap on your lawn, near enough for correct plug type and gap specifications.
GTX 1054 Operator's Manual - Page 21
... coupler to the operator's position and engage the PTO. Remain in the FAST (rabbit) position.
6. Turn the ignition key to the STOP position to prevent unintended starting.
Before lubricating, repairing, or inspecting the tractor, always disengage PTO, set parking brake, stop engine and remove key to turn the tractor's engine off and detach the hose coupler from...
GTX 1054 Operator's Manual - Page 22
.... The first measurement taken should be between 1⁄4-inch and 3⁄8-inch lower than the second measurement. Maintenance & Adjustments Adjustments
WARNING! Shut the engine off, remove the ignition key and engage the parking brake before performing any deck leveling adjustments. The front of the deck should be between 1⁄4-inch and 3⁄8-inch...
GTX 1054 Operator's Manual - Page 26
... both ends of the hanger bracket on the tractor's right side.
8. Protect your tractor's PTO system. Place a block of the blade has previously been sharpened, or if any metal separation... out of the blades along the cutting edges, parallel to expose its underside.
2.
6. Shut the engine off and remove ignition key before removing the cutting blade(s) for cracks or damage, especially ...
GTX 1054 Operator's Manual - Page 28
... repairing, or
inspecting, always disengage PTO, set parking
brake, stop engine and remove key to engage and disengage safely.
Remove the deck ...instructed in Figure 7-8. Shut the engine off and remove ignition key before removing the cutting... All belts on your tractor are specially designed to prevent
unintended starting.
5.
Loosen, but not removed, in Figure 7-8.
Service
Belt...
GTX 1054 Operator's Manual - Page 30
... pressure. Connect wire(s) to -side deck adjustment.
2. Move Throttle/Choke control out of oil.
2. Replace air cleaner paper element or clean foam pre-cleaner.
1. Perform side-to spark plug(s).
4. Troubleshooting
8
Problem
Engine fails to start
Engine runs erratic
Engine overheats Engine hesitates at high RPM Engine Idles rough Excessive vibration Uneven cut
Cause
1. Water...
Similar Questions
Cub-cadet-cc30e-lawn-mower
cub-cadet-cc30e-lawn-mower won`t just beeps after inserting the key. The battery fully charged
cub-cadet-cc30e-lawn-mower won`t just beeps after inserting the key. The battery fully charged
(Posted by paulross 1 year ago)
With Clutch Push In Mower Will Start Let Clutch Out Tractor Will Die
(Posted by Dstout789 1 year ago)
One Of The Safety Switches Is Not Making Contact
I believe the brake safety switch is not is not making contact, so that the tractor won't start, hav...
I believe the brake safety switch is not is not making contact, so that the tractor won't start, hav...
(Posted by aroth1954 3 years ago)
Loud Slapping Sound When Starting Gtx 1054
Replaced bad solenoid and started tractor. Let the tractor run a while than engaged the pto and ran ...
Replaced bad solenoid and started tractor. Let the tractor run a while than engaged the pto and ran ...
(Posted by jwread101 3 years ago)
Lawn Mower Not Starting.
Our lawn mower will not start. We replaced battery and now it acts like it wants to crank but won't....
Our lawn mower will not start. We replaced battery and now it acts like it wants to crank but won't....
(Posted by TDivens1972 6 years ago)