Home » Cub Cadet » Lawn & Garden » Cub Cadet 530 SWE

Cub Cadet 530 SWE Support Question

Find answers below for this question about Cub Cadet 530 SWE.
Need a Cub Cadet 530 SWE manual? We have 3 online manuals for this item!

Cub Cadet Overview Questions Manuals Reviews Videos Research

Question posted by vga63new on November 29th, 2015

How To Re-assemble Chute Joystick For Cub Cadet 530 Swe Snow Thrower

How do I put the chute joystick back together. The trigger stopped working, it had no resistance. When I took the screws out of the joystick it all came apart and everything fall out. All pieces appear to be intact and not broken. I can't find instructions on how to re-assemble the joystick. Could you provide instructions? Thank you.

Requests for more information

Request from vga63new on November 30th, 2015 7:00 PM
The answer you provided is for lower chute replacement not re-assembling the joystick. Do you have any instructions for reassembling the joystick?

Request from vga63new on November 30th, 2015 7:11 PM
Sorry but the manual you provided is the same as mine and it does not show how to assemble the joystick.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on November 30th, 2015 7:38 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,700

1,100
points

See https://www.youtube.com/watch?v=Xk7qQrpSeBk.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Cub Cadet 530 SWE Manual Pages

Jet Sweep Warranty Information - Page 1

... loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for a particular purpose, applies after the applicable period of..., shall bind Cub Cadet. Replacement parts that vary in the following cases: a. Transportation charges and service calls. CUB CADET LLC MANUFACTURER'S LIMITED WARRANTY FOR SNOW THROWERS, LOG SPLITTERS,...

500 Series Snow Throwers Brochure - Page 1

...;See specifications for better maneuverability. sinGle-hand chUTe conTrol 4-way chute control allows you to be thrown. easy operation makes for smoother clearing of the cold faster. 500 series Two-sTaGe snow Throwers 524 we 524 Swe 526 Swe 528 Swe ideaL For moderaTe To HeaVY, deeP Snow and wide areaS. 530 Swe ideaL For moderaTe To HeaVY, deeP, weT...

500 Series Snow Throwers Brochure - Page 2

... BLUE™ rust-resistant, non-marking, reversible Steel 2 qt. 5 qt. 5 qt. 208cc Cub Cadet® OHV 4-cycle 277cc Cub Cadet® OHV 4-cycle 277cc Cub Cadet® OHV 4-cycle 265 lbs. 275 lbs. 285 lbs. 3-year limited residential 1-year limited commercial 530 SWE 30" Steerable wheel/ positive traction Power steering/trigger Standard 16" x 6.5" 5 qt. 357cc Cub Cadet® OHV 4-cycle...

524 WE Operator's Manual - Page 1

... 44136-0019 Form No. 769-08161 (May 29, 2012) Printed In USA CUB CADET LLC, P.O. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Two Stage Snow Thrower - 524 WE, 524 SWE, 526 SWE, 528 SWE & 530 SWE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL...

524 WE Operator's Manual - Page 2

... Snow Thrower. Characteristics and features discussed and/or illustrated in personal injury or property damage. We reserve the right to provide excellent performance when properly operated and maintained. Please refer to the engine manufacturer's Owner's/Operator's Manual, packed separately with regards to Cub Cadet LLC • P.O. Table of Contents Safe Operation Practices 3 Assembly...

524 WE Operator's Manual - Page 5

... a complete stop the engine. Never store the machine or fuel container inside the discharge chute is an open...or 60 hours of engine governor. Snow thrower shave plates and skid shoes are working condition. Maintain or replace safety and ...screws for gas, oil, etc. Box 361131 Cleveland, Ohio 44136-0019. Always use your safety protection, frequently check all control levers and stop...

524 WE Operator's Manual - Page 7

... Snow Thrower • One Chute Control Rod • One Snow Thrower Operator's Manual • Two Replacement Auger Shear Pins • One Chute Assembly • One Product Registration Card • One Engine Operator's Manual Assembly Remove all loose parts before pivoting the handle upward. Pivot the handle upward. Remove hairpin clip, wing nut and hex screw from chute control...

524 WE Operator's Manual - Page 9

... cable guide. NOTE: The chute control rod will be to chute support joystick. Insert the chute control rod into the pinion gear. gear. Figure 3-8 7. Check that all be visible after the rod has been inserted. 6. Assembly & Set-Up 9 NOTE: For smoothest operation, the cables should all cables are included with your snow thrower's dash panel until the...

524 WE Operator's Manual - Page 10

...'s recommended psi. The tires are adjusted upward at all times. Check the tire pressure before operating the snow thrower. Assembly & Set-Up Figure 3-13 2. Retighten nuts and bolts securely. 10 Section 3- Chute Clean-Out Tool The chute clean-out tool is fastened to the top of the auger housing with force sufficient to cause serious...

524 WE Operator's Manual - Page 11

... the snow thrower), engage the auger. 4. Confirm that the auger has completely stopped rotating and shows NO signs of the auger control as follows: 1. Stop the engine. Refer to increase cable tension). 9. Repeat steps 2 through 6 above to the Engine Operator's Manual packed with 4-Way Chute Control are also controlled by changing the angle of the chute assembly...

524 WE Operator's Manual - Page 12

... There are six forward (F) speeds. Adjust upward for hard-packed snow. Controls and Features Drive Control Chute Assembly Clean Out Tool Headlight † 4 Shift Lever Chute Directional Control Auger Control Heated Grips † Steering Trigger Control † Augers Skid Shoe † If Equipped Figure 4-1 Snow thrower controls and features are described below and illustrated in the...

524 WE Operator's Manual - Page 13

... the control grip against the handle to engage the wheel drive. Failure to stop . The left and right wheel steering trigger controls are familiar with the drive control, the operator can operate the chute directional control without interrupting the snow throwing process. The drive control also locks the auger control so that you wear...

524 WE Operator's Manual - Page 14

... behind the snow thrower), engage the auger control for a few seconds to safely clean the chute assembly and chute opening: 1. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to clear any snow and ice which has formed in the operator's position (behind handles until all moving parts have stopped before unclogging. Stop the engine...

524 WE Operator's Manual - Page 16

... around the spacers and the flange bearings found at either end of the snow thrower are to the snow thrower. 2. Tire Pressure Refer to wear. Shave Plate and Skid Shoes The shave...° to the Engine Operator's Manual. Spray lubricant inside of carriage bolts are subject to Assembly and Set-up section for clarity. Maintenance & Adjustments 6 Maintenance Engine Refer to use the ...

524 WE Operator's Manual - Page 17

... Cable If the full range of operation. 1. Figure 6-5 Figure 6-3 3. Chute Assembly Refer to the Assembly and Set-up section for instructions on the shift cable index bracket. Maintenance & Adjustments 17 Remove the frame cover from the underside of the snow thrower by removing the self-tapping screws which secure it is out of engine oil (or...

524 WE Operator's Manual - Page 18

... the drive cable or if the snow thrower's drive is disengaging intermittently during operation, the cable may be no resistance in a clean, dry area. 3. Engage the drive control and gently attempt to increase cable tension). 4. Loosen the lower hex screw on storing your engine. 18 Section 6 - Pull out the chute control rod until the hole...

524 WE Operator's Manual - Page 20

... the snow thrower by running engine until it . Do not attempt to the frame after installing a replacement auger belt. 9. See Figure 7-6: Figure 7-5 8. Pivot the idler pulley toward the right. c. Lift the drive belt off the engine pulley. Remove the frame cover from tank by removing the self-tapping screws which secure it stops. Remove...

524 WE Operator's Manual - Page 21

...screw and bell washer which secure it rests on ordering a Service Manual. See your authorized service dealer to run until it . Do not attempt to be replaced. Stop Bolt Friction Wheel Removal (524 WE) If the snow thrower... 7 - See Figure 7-8. Friction Wheel Inspection (524 SWE, 526 SWE, 528 SWE & 530 SWE) If the snow thrower fails to drive with the drive control engaged, and performing...

524 WE Operator's Manual - Page 25

... your Cub Cadet snow thrower. Attachments & Accessories 10 The following attachments and accessories are available for your snow thrower for information regarding price and availability. Model Number Description 929-0071A Extension Cord, 110V 753-05762A Heated Grips* OEM-390-679 Drift Cutter Kit OEM-390-995 Snow Thrower Protective Cover 490-241-0013 Snow Thrower Auger and Chute...

524 WE Operator's Manual - Page 28

... Cub Cadet. Cub Cadet does not extend any kind be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn ...use or exposure. CUB CADET LLC MANUFACTURER'S LIMITED WARRANTY FOR SNOW THROWERS The limited warranty set forth below is available, WITH PROOF OF PURCHASE, through Cub Cadet's authorized channels of...